There are 1 repository under bme280 topic.
Flipper Zero application for reading temperature, humidity and pressure sensors like a DHT11/22, DS18B20, BMP280, HTU21 and more
Smogly(formerly: Smogomierz) - simple and cheap PM 2.5 and PM10 sensor based on NodeMCU (ESP8266) or ESP32
Apache Mynewt Sensor Network Application for STM32 Blue Pill and nRF52 with Visual Rust, NB-IoT, GPS, iBeacon, NimBLE, ESP8266 (WiFi Geolocation) and nRF24L01
WT32-ETH01 LAN 8720 RJ45 wired Wireless-tag
Drivety: Smart App Assistant to Secure Inside Car Activity. #AndroidDevChallenge
ESPHome configuration for a DIY indoor air quality monitor for CO₂ concentration, PM2.5 and PM10 concentrations, and temperature, humidity and pressure
A platform agnostic Rust driver for the Bosch BM[PE]-280
MicroPython MQTT & code example for Eduponics mini ESP32 learning kit
GPS IoT tracker board for scanning gps and environment information and sending this to a MQTT server via GPRS.
Sample code for reading values from a BME280 temperature-humidity-pressure sensor, via ESP-IDF's I2C master driver, supports both normal mode and forced mode described in the datasheet. https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME280_DS001-11.pdf
A low power LoRaWAN Node
💧 Arduino library for Bosch Sensortec BME280 – combined temperature, pressure, humidity sensor. The library allows using the sensor over I2C or SPI on any board that supports Arduino.
weather station, arduino esp8266, st7920, mh-z19, BME-280
ESP8266 and BME280 sensor for a minimalist weather station to put on your terrace
Smarthome for Caravans and Motor Homes - System for measuring and displaying various values in caravans and motor homes, including climate values, fill levels and leveling data, energy data, propane/butane sensor. incl. display, config website, test routines, etc. Own circuit board created
ESP8266 + BME280 -> MQTT, Serial, HTTP-Server, HTTP-Client/Volkszähler
A simple Prometheus exporter for metrics from Bosch BME280 sensors for ESP8266 based boards with NodeMCU firmware.
IoT program for Arduino Uno / STM32 Blue Pill (libopencm3) that reads BME280 temperature + humidity + altitude sensors, via I2C or SPI with DMA and multitasking. Sends sensor data to Sigfox via Wisol Sigfox module on UART. Runs on cocoOS task scheduling library http://www.cocoos.net
Visual Programming for Zig with NuttX Sensors
Battery/solar-powered ESP32 TTN (LoraWAN) sensor for measuring temperature, humidity, air pressure and fine dust.
BMP280 and BME280 I2C driver for ESP32 boards using the IDF toolchain.
MQTT Sensor project with BME280 for smart home 🏡 automation
nRF24LE1 remote sensor module, support DHT21/22, DS18B20, photoresistor as light sensor, AES encryption
ESP8266 CCS811/BME280 MQTT air quality sensor
This repository contains all the code and steps required to setup a BME280 with the Heltec CubeCell HTCC-AB01 on TTN Australia.
💨 A collection of tiny and ultra-cheap web things for monitoring air quality. The devices measure: temperature, humidity, barometric pressure, the concentration of carbon dioxide, dew point. The devices easily integrate into the Web of Things ecosystem and can be used indoor or outdoor.
An air quality sensor and display that uses the BME280 and CCS811 sensors to read temperature, relative humidity, equivalent CO2 (eCO2) and Total Volatile Organic Compound (TVOC) and displays the values on a 2.9in Waveshare e-Paper display.