Humanoid Control

Build and Start

OCS2

OCS2 is a huge monorepo; DO NOT try to compile the whole repo. You only need to compile ocs2_legged_robot_ros and its dependencies following the step below.

You are supposed to clone the OCS2, pinocchio, and hpp-fcl as described in the documentation of OCS2.

# Clone OCS2
git clone https://github.com/leggedrobotics/ocs2.git
# Clone pinocchio
git clone --recurse-submodules https://github.com/leggedrobotics/pinocchio.git
# Clone hpp-fcl
git clone --recurse-submodules https://github.com/leggedrobotics/hpp-fcl.git
# Clone ocs2_robotic_assets
git clone https://github.com/leggedrobotics/ocs2_robotic_assets.git
# Install dependencies
sudo apt install liburdfdom-dev liboctomap-dev libassimp-dev

Compile the ocs2_legged_robot_ros package with catkin tools instead of catkin_make. It will take you about ten minutes.
```
catkin config -DCMAKE_BUILD_TYPE=RelWithDebInfo #important
catkin build ocs2_legged_robot_ros ocs2_self_collision_visualization
```
Ensure you can command the ANYmal as shown in the document and below.

Mujoco

For the latest version of mujoco, it is very easy to install it on python:

pip3 install mujoco
pip3 install pynput #for teleop.py

Getting Start

catkin config -DCMAKE_BUILD_TYPE=RelWithDebInfo #important
catkin build humanoid_controllers humanoid_legged_description mujoco_sim
# To start simulation with the cheat state estimator.
# Press SPACE on mujoco simulation window and input the gait command. 
roslaunch humanoid_controllers load_cheat_controller.launch
# To start simulation with the normal state estimator.
roslaunch humanoid_controllers load_normal_controller.launch
# To start only the NMPC module and simulate with OCS2 dummy node
roslaunch humanoid_dummy legged_robot_sqp.launch

The effect of the simulation is shown in the video provided in this link. (Note: The video version is older, and the actual effect may vary depending on the latest code).

Framework

Foot Planner

The foot planner is a switch model provided by OCS2, which switch the contact status between right foot and left foot. The foot planner only plans the z-axis of swinging foot as Cubic Spline.

State Estimator

The state estimator only needs to estimate the coordinates and linear velocity of the trunk. It is a linear Kalman filter, where the system's state equation is

$$ \begin{split} \begin{cases} \ \ \hat{x}(k) = A\hat{x}(k-1) + Bu(k)+\omega(k-1) \\ \ \ z(k) = H\hat{x}(k) + \nu(k) \\ \end{cases}\end{split} $$

where $x$, $u$, $z$ are defines as

$$ \begin{split} x &= [\mathbf{pos_b}^T, \mathbf{vel_b}^T, \mathbf{pos_c}^T]^T\\ u &= \mathbf{acc_b}\\ z &= [-\mathbf{pos_{local,c}}^T, \mathbf{vel_{b}}^T,\mathbf{height_c}^T]^T = [-\mathbf{pos_{local,c}}^T, -\mathbf{vel_{local,c}},\mathbf{0}^T]^T,\text{for contact foot}\\ \end{split} $$

Where the subscript $b$ refers to the trunk, subscript $c$ refers to the foot-end contact point, and subscript $local$ refers to the quantity in the trunk coordinate system.

In the state estimator, $z$ is obtained from the robot's kinematics, and only the kinematics of the supporting foot is trusted. The noise parameters related to the swinging foot will be set to a very large 'distrust value.' At this time, since the state equation only accepts updates from the accelerometer, and the Q parameter for the supporting foot is much smaller than that for the swinging foot, it is possible to achieve an estimation where the position of the supporting foot remains unchanged, and the position changes when it switches to the swinging foot. Moreover, since only the dynamics of the supporting foot are trusted, the height and velocity measurement of the foot can be directly set to 0.

NMPC

The NMPC part solves the following optimization problems at each cycle through the formulation and solving interfaces provided by OCS2:

$$ \begin{split} \begin{cases} \underset{\mathbf u(.)}{\min} \ \ \phi(\mathbf x(t_I)) + \displaystyle \int_{t_0}^{t_I} l(\mathbf x(t), \mathbf u(t), t) , dt \\ \text{s.t.} \ \ \mathbf x(t_0) = \mathbf x_0 ,\hspace{11.5em} \text{initial state} \\ \ \ \ \ \ \dot{\mathbf x}(t) = \mathbf f(\mathbf x(t), \mathbf u(t), t) \hspace{7.5em} \text{system flow map} \\ \ \ \ \ \ \mathbf g_1(\mathbf x(t), \mathbf u(t), t) = \mathbf{0} \hspace{8.5em} \text{state-input equality constraints} \\ \ \ \ \ \ \mathbf g_2(\mathbf x(t), t) = \mathbf{0} \hspace{10.5em} \text{state-only equality constraints} \\ \ \ \ \ \ \mathbf h(\mathbf x(t), \mathbf u(t), t) \geq \mathbf{0} \hspace{8.5em} \text{inequality constraints} \end{cases}\end{split} $$

In this framework, the system state $\mathbf{x}$ and system input $\mathbf{u}$ are defined by the OCS2 Centroidal Model, eliminating the need for us to manually define them. The definition of $\mathbf{x}$ and $\mathbf{u}$ according to OCS2 is as follows:

$$ \begin{equation} \mathbf{x}= [\mathbf{h}_{com}^T, \mathbf{q}_b^T, \mathbf{q}_j^T]^T, \mathbf{u} = [\mathbf{f}_c^T, \mathbf{v}_j^T]^T \end{equation} $$

where $\mathbf{h}_{com} \in \mathbb{R}^6$ is the collection of the normalized centroidal momentum, $\mathbf{q}=[\mathbf{q}_b^T, \mathbf{q}_j^T]^T$ is the positions of the generalized coordinate, which $\mathbf{q}_b^T$ is the 6-dof position of base, $\mathbf{q}_j^T$ is the postion of every joint. In this framework, the dimension of $\mathbf{x}$ is 24.

$\mathbf{f}_c \in \mathbb{R}^{12}$ consists of contact forces at four contact points. In this framework, we define four 3-dof contact points which refer to the toe and heel of left and right feet. $\mathbf{v}_j$ is the joint velocities. While the cost function is simply the quadratic cost of tracking the error of all states and the input, the system dynamics uses centroidal dynamics with the following constraints:

Friction cone;
No motion at the standing foot;
Zero force at the swinging foot;
The z-axis position of the swinging foot satisfies the gait-generated curve;
No motion for the roll axis of the foot.

To solve this optimal control problem, a multiple shooting is formulated to transcribe the optimal control problem to a nonlinear program (NLP) problem, and the NLP problem is solved using Sequential Quadratic Programming (SQP). The QP subproblem is solved using HPIPM.

WBC

WBC only considers the current moment. The WBC optimization task is expressed in the following form according to qpOASES:

$$ \begin{split} \min_{x} & \frac{1}{2} x^{T} H x+x^{T} g(w_{0}) \\ \text { s.t. } & lbA(w_{0}) \leq A x \leq ubA(w_{0}), \\ & lb(w_{0}) \leq x \leq ub(w_{0}), \end{split} $$

Where $x$ is the optimization variable, with a dimension of 42 in this framework, defined as follows:

$$ \begin{equation} x= [\mathbf{a}_{b}^T, \mathbf{a}_j^T, \mathbf{f}_c^T, \mathbf{T}_j^T]^T\end{equation} $$

where $\mathbf{a}_{b}^T \in \mathbb{R}^6$ is the base acceleration, $\mathbf{a}_j^T \in \mathbb{R}^{12}$ is the joint acceleration, $\mathbf{f}_c^T \in \mathbb{R}^{12}$ is the contact force and $\mathbf{T}_j^T \in \mathbb{R}^{12}$ is the joint torque.

In weighted WBC, a portion of the tasks serves as weighted costs, providing the optimization problem's $H$ and $g(w_0)$. Another portion of the tasks serves as constraints, providing $A$, $lbA$, $ubA$, $lb$, and $ub$. The definition of the tasks is shown in the following table.

Type	Task
cost	Base XY linear acceleration task
cost	Base Z position task (using PD controller to estimate the acceleration)
cost	Base Angular task (using PD controller to estimate the acceleration)
cost	Swing leg position task (using PD controller to estimate the acceleration)
cost	Contact force task
constraint	Floating base EOM task
constraint	Torque limit task
constraint	Friction cone task

Every task is defined as a quadruple $\left(A, b, D, f\right)$ where

$$ \begin{split} Ax -b = w\\ Dx - f \leq v\\ w \rightarrow 0, v \rightarrow 0 \end{split} $$

To formulate the QP problem from task definitions, we use the following formula:

For cost task, we have $H=A^TA$ and $g=-A^Tb$.

For equality constrained task, we have $A_{qp} = A,lbA=b, ubA=b$

For non-equality constrained task, we have $A_{qp} = D,lbA=-\infty, ubA=f$

The stacking of tasks is defined as the concatenation of the matrices $A$, $b$, $D$, and $f$. Once multiple tasks are stacked, the parameters of the QP problem are obtained using the aforementioned formula. The qpOASES solver is then used to solve the problem.

PD controller

Obtain optimized joint positions and joint velocities from MRT (Model Reference Tracking), obtain joint accelerations and joint torques from WBC (Whole Body Control), and feed them into a PD controller after processing. MRT, based on the trajectory optimized by NMPC, obtains the optimized states and inputs at a high frequency.

$$ \begin{split} \mathbf{q_des} &= \mathbf{q_opt} + \frac{1}{2}\mathbf{a}_jt^2\\ \mathbf{v_des} &= \mathbf{v_opt} + \mathbf{a}_jt\\ \mathbf{T_des} &= \mathbf{T}_j \end{split} $$

where $t$ is the WBC period.

Frequency

Module	Frequency
NMPC	100Hz
MRT	500Hz
WBC	500Hz
PD Controller	>1000Hz
State Estimate	500Hz

To ensure the speed of the program, it is crucial that you optimize the code at least to the RelWithDebInfo level. This is highly important!

Acknowledgement

legged-control by Qiayuan Liao: Nonlinear MPC and WBC framework for legged robot based on OCS2 and ros-controls.

hunter-bipedal-control by BridgeDP: An open source bipedal robot control framework, based on non-linear MPC and WBC, tailered for EC-hunter80-v01 bipedal robot.

pai-sim by High-Torque: Acknowledgement for the Mujoco simulation framework in python.

pocketxjl / humanoid-control