Giters
lincomatic
/
open_evse
Firmware for Open EVSE
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
112
Watchers:
28
Issues:
95
Forks:
160
lincomatic/open_evse Issues
ESP miss boot from OpenEvse and dont get the state of the atmega boot notif
Updated
2 months ago
Comments count
15
RAPI command to enable/disable bootlock
Updated
7 months ago
Comments count
4
OpenEvse trigger GFCI Fault with test disabled
Updated
7 months ago
RAPI commands for over current detection
Updated
9 months ago
Stuck open contactor not annunciated properly
Updated
9 months ago
Comments count
3
OpenEVSE with battery don't detect power loss
Updated
a year ago
Comments count
1
Test failed - stuck relay issue
Closed
a year ago
Comments count
1
Substitute RGB LCD for monochrome LCD with PCF8574 interface module
Closed
a year ago
Comments count
3
Tore calibration and error margin depending on calibration value
Closed
a year ago
Comments count
1
missing I2C temperature sensors
Closed
a year ago
Comments count
2
AutoSetCurrentCapacity() should set a max current capacity not actual charge current.
Closed
a year ago
Comments count
14
OpenEVSE don't detect plug anymore since new firmware
Closed
a year ago
Comments count
4
The energy history is extremely chatty
Closed
a year ago
Comments count
1
Support for other GFI CTs?
Closed
a year ago
Comments count
1
OpenEVSE start a session when there is no ESP connected
Closed
a year ago
Comments count
7
Possibilty to set the current more precisely ?
Closed
a year ago
Comments count
1
OpenEVSE start full amp when changing state from disable to active
Closed
a year ago
Comments count
3
`stable` branch
Closed
2 years ago
Comments count
5
Questions about RAPI
Closed
2 years ago
Comments count
2
OpenEVSE state flow chart and testing
Closed
2 years ago
Comments count
6
LCD changes in latest build
Closed
2 years ago
Comments count
11
Extra space in `$GI` response
Closed
2 years ago
Comments count
2
`ECF_AUTO_SVC_LEVEL_DISABLED` not set when `AUTOSVCLEVEL` is not defined
Closed
2 years ago
Comments count
2
RAPI $ST command
Closed
2 years ago
Comments count
12
`$SH` and sleep timer
Closed
2 years ago
Comments count
1
MennekesLock
Closed
2 years ago
Comments count
21
Automated build and merging forks
Closed
2 years ago
Comments count
12
RAPI Command Serial Numbers
Closed
2 years ago
Comments count
12
Connect LED without i2c
Closed
3 years ago
Comments count
6
Random resets after D7.1.3 upgrade
Closed
3 years ago
Comments count
5
EVSE reboot when going into an error state
Closed
3 years ago
Comments count
7
Fault counters
Closed
3 years ago
Comments count
2
Connected state change while sleeping
Closed
3 years ago
Comments count
3
Physical Security - RAPI command to disable button.
Closed
4 years ago
Comments count
11
Detecting three phase power
Closed
4 years ago
Comments count
8
Variables undefined if KWH_RECORDING is not defined. Won't compile.
Closed
4 years ago
Comments count
2
How to flash
Closed
4 years ago
Comments count
16
RAPI command to set voltage
Closed
4 years ago
Comments count
7
RAPI command to set MAX current
Closed
4 years ago
Comments count
7
Bug Report
Closed
4 years ago
Comments count
1
$AT event not sent while sleeping
Closed
4 years ago
Comments count
2
Current is only sampled while charging
Closed
4 years ago
Comments count
1
MOSI output for Type 2 socket locking actuator
Closed
4 years ago
Comments count
2
AUTH_LOCK 1 cannot be turned off by RAPI "S4 0" while in EVSE_STATE_A
Closed
4 years ago
Comments count
1
Bad temperature reading between 0oC and -0.5oC
Closed
4 years ago
Comments count
4
Compiling openenergeymonitor/open_evse
Closed
4 years ago
Comments count
9
PlatformIO vs Arduino IDE: same binary firmware?
Closed
5 years ago
Comments count
14
Sleeping does not indicate auth lock status
Closed
4 years ago
Comments count
1
Newbie
Closed
5 years ago
Comments count
5
RAPI over I2C
Closed
5 years ago
Comments count
1
Previous
Next