Giters
lincomatic
/
open_evse
Firmware for Open EVSE
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
113
Watchers:
28
Issues:
95
Forks:
159
lincomatic/open_evse Issues
Should I really use Arduino 1.6
Closed
5 years ago
Comments count
1
Going to sleep while charging trips GFCI
Closed
4 years ago
Comments count
5
In order to start support of car identification
Closed
5 years ago
Comments count
3
RAPI command to set voltage
Closed
5 years ago
Comments count
5
State: EV Connected / Disconnected while sleeping
Closed
5 years ago
Comments count
6
Is it possible to run OpenEVSE without an LCD display?
Closed
5 years ago
Comments count
9
PCF8574 support
Closed
6 years ago
Comments count
4
Energy Limit: additive rather than cumulative
Closed
6 years ago
Comments count
2
Overcurrent feature: delay required
Closed
6 years ago
Comments count
16
Auth_Lock and EEPROM
Closed
6 years ago
Comments count
1
Pin change RelayAC
Closed
6 years ago
Comments count
5
Where can I find eeprom_24.bin?
Closed
6 years ago
Comments count
1
PP_AUTO_AMPACITY should set absolute maximum charge for a single session
Closed
6 years ago
Comments count
7
$FS 'rebounds' when trying to pause a delay timer charge
Closed
6 years ago
Comments count
1
$FE does not work when delay timer is active
Closed
6 years ago
Comments count
11
Overcurrent cutout?
Closed
6 years ago
Comments count
7
PP_TABLE_TESLA?
Closed
6 years ago
Comments count
3
Delay end time not stopping charge
Closed
6 years ago
Comments count
17
230v/400v single/three phase detection and correct energy calculations.
Closed
6 years ago
Comments count
2
Restore LCD display after corruption
Closed
6 years ago
Comments count
5
Alert user when temperature throttling was activated during a charge session
Closed
6 years ago
Comments count
15
Set temporary (single session only) charging current
Closed
6 years ago
Comments count
4
Session elapsed time should be consistent with session energy
Closed
6 years ago
Comments count
3
extended_fuses setting causes unreliable booting
Closed
7 years ago
Comments count
1
Session Wh Counter Code Not Accurate
Closed
7 years ago
Comments count
1
Session Wh counter does not reset if using delay timer
Closed
7 years ago
Comments count
3
LCD RGB backlight colour changes
Closed
7 years ago
Comments count
5
L2 minimum current should be 6A not 10A?
Closed
7 years ago
Comments count
4
$FP command causes crash
Closed
7 years ago
Comments count
1
Testing for supported features
Closed
7 years ago
Comments count
1
No RAPI API for enabling/disabling the temperature checking
Closed
7 years ago
Comments count
9
No RAPI API for getting the current delay timer
Closed
7 years ago
Comments count
1
Async event for setting change
Closed
5 years ago
Comments count
4
Setting the LCD text via RAPI can corrupt display
Closed
7 years ago
Comments count
2
Setting the charge/time limit via RAPI does not update LCD
Closed
7 years ago
Comments count
2
Service level display issue
Closed
7 years ago
Comments count
1
m_TMP007_temperature stuck at initialization of 230 if not present
Closed
7 years ago
Comments count
5
Issue compiling latest stable when you undefine RTC
Closed
8 years ago
Comments count
2
Compile Error
Closed
8 years ago
Comments count
2
Temperature monitoring - subzero temps
Closed
8 years ago
Comments count
4
RAPI response has no checksum
Closed
8 years ago
Comments count
5
RAPI GS command response and ST asynchronous have different number format
Closed
5 years ago
Comments count
3
Sleep status cause problem on Smart ED
Closed
9 years ago
Comments count
4
GetChargingCurrent returns last charging current after charging
Closed
9 years ago
Comments count
1
Previous
Next