ee445l-linux

A complete repository for writing, compiling and flashing code for the TI Stellaris, along with a sample project. Based on a completely open-source toolchain, without the need to rely on cumbersome development environments.

Tested on OS X and Ubuntu 16.04. Should work on most GNU/Linux/POSIX environments.

Requirements

Follow the instructions in the next section to install the required packages.

Installing

Create a duplicate of this repository for you own local development by doing the following:
1. Create a new github repository and name it to your liking. Make sure it is Private.
2. Open terminal.
3. Create a bare clone of the repository:
```
$ git clone --bare https://github.com/jishminor/ee445l-linux.git
```
4. Mirror push to the new repository made in step i:
```
$ cd ee445l-linux.git
$ git push --mirror https://github.com/exampleuser/your-repository.git
```
5. Remove the temporary local repository you created in step iii:
```
$ cd ..
$ rm -rf ee445l-linux.git
```
6. Now navigate to a directory of your choice and clone your new repository:
```
$ git clone https://github.com/exampleuser/your-repository.git
```
In the root directory of your repo, run

For OS X:
```
$ bash setup-osx.sh
```
For Linux:
```
$ bash setup-linux.sh
```
to install all dependencies.
If prompted to override rwxr-xr-x root/admin for /usr/local/bin/lm4flash, enter y and press enter.

Run Test Project

Hook up an unlocked TM4C via USB on the debug port (top). Move to the TestProject directory then build the project and flash by running:

$ cd TestProject
$ make flash

If all goes correctly, the blue LED should come on and your up and running!

Working on a New Project

The general workflow for beginning a new project is a follows:

Create directory in git root directory corresponding to the lab you are working on (ie lab1, lab2, etc). To use the given gitignore, make sure it is all lower case.
```
$ mkdir lab1
```
Copy over Makefile from the TestProject directory into the new lab directory.
```
$ cp TestProject/Makefile lab1/
```
Run text editor of choice to modify lab1/Makefile, for example vim
```
$ vim lab1/Makefile
```

Find the line

PROJ_NAME = TestProject

and change it to

PROJ_NAME = lab1

Add all the starter files you need to the lab1 directory and get coding!

Good Practice: The shared directory is great for placing the modules you write that can be shared across projects. There's already a few in there from ValvanoWare which you will find useful through the semester. To include files from this directory in your projects just place a

#include shared/your_file.h

at the top of a c file which you need the module in.

Usage

To build project in current directory:

$ make

To flash the TM4C:

For OS X: $ make flash

For Linux: $ sudo make flash

To clean up the directory:

$ make clean

Debugger

The debugger requires gdb-arm-none-eabi and openocd in addition to the other dependencies. They should also be installed by the install script.

To start debugging, run the following commands in your project folder:

$ sudo make flash
$ make debug

Then run the following GDB commands:

(gdb) target remote localhost:3333
(gdb) monitor reset halt
(gdb) load

It might print an message in the middle, but it seems to not be a problem as long as you flash the board with the project you're debugging beforehand.
Now everything is ready to go like a normal GDB session. Set any desired breakpoints and then type continue or c to continue running the program.

When your done with your session:

(gdb) q

and don't forget to kill openocd:

sudo pkill openocd

Authors

Josh Minor - jishminor
Sean Kirmani - kirmani

Acknowledgments

Thanks to Christian Jann for his tutorial https://www.jann.cc/2012/12/11/getting_started_with_the_ti_stellaris_launchpad_on_linux.html

jishminor / ee445l-linux