Crazyswarm

A Large Nano-Quadcopter Swarm.

The documentation is available here: http://crazyswarm.readthedocs.io/en/latest/.

Troubleshooting

Please start a Discussion for...

Getting Crazyswarm to work with your hardware setup.
Advice on how to use the Crazyswarm Python API to achieve your goals.
Rough ideas for a new feature.

Please open an Issue if you believe that fixing your problem will involve a change in the Crazyswarm source code, rather than your own configuration files. For example...

Bug reports.
New feature proposals with details.

QUICK START

Quick start guide on setting up crazyflies for our lab.

The official documentation in crazyswarm is pretty good. Id highly recommend reading that too/first.

Software Installation

As of Feb 2 2022, Ubuntu 20 installation worked, but ubuntu 18 did not work for us. Some issue in the libmotioncapture sdk.

You will need

ROS
cfclient (python3 -m pip install cfclient)
cflib (Optional, will be autoinstalled by cfclient) (python3 -m pip install cflib)
crazyswarm (Follow instructions at https://crazyswarm.readthedocs.io/en/latest/installation.html)
We used Ubuntu 20, and Python3

Hardware Setup

Update the radio firmware following instructions here: https://github.com/bitcraze/crazyradio-firmware Note, you should always use python3 commands, not python as some of the documentation suggests. The radio module is labelled with "PA" on radios in our lab.
If you get 'No module named usb run python3 -m pip install pyusb
Update the firmware on the quad using instructions here: https://www.bitcraze.io/documentation/repository/crazyflie-firmware/master/building-and-flashing/build/ or using the cfclient
Connect crazyradio to the usb port.
Connect battery to crazyflie. Note the number of the crazyflie, as this is the ID of the drone.
Open cfclient (In terminal cfclient)
Where you see Addreses (near top left) set the address in the following form 0xE7E7E7E7<ID> where <ID> is the quad's id.
Hit Scan
You should see the interface switch to something like radio://0/40/2M/E7E7E7E7<ID> where the first arg is the usb device number (assigned by Ubuntu) the second is the channel number (needed later) the third is the data rate (eg 2M), and the fourth is the uri of the quad.
It should now have connected to the quad. Moving the quad should move the horizon.
Create a object in vicon tracker for this quad. Call the object cf<ID>, for instance, for crazyflie id 7, it should be labelled cf7. Make sure the forward direction on the quad is aligned to the +X axis of the vicon room.

First Flight

IN TERMINAL 1:

cd crazyswarm the package provided by crazyswarm
export CSW_PYTHON=python3
./build.sh to build the project (build is used instead of catkin_make or anything similar)
cd ros_ws and source devel/setup.bash
Next, we run through configuration: https://crazyswarm.readthedocs.io/en/latest/configuration.html#
Configure crazyswarm/ros_ws/src/crazyswarm/launch/allcrazyflies.yaml Here, add a config for each crazyflie you will be running. Use the ID, channel etc from earlier setup. The initial position will be ignored if using motionCapture. Type='default' for the small crazyflies.
Choose which crazyflies will be run in current experiment. cd crazyswarm/ros_ws/src/crazyswarm/scripts and run python3 chooser.py Use the checkboxes to select which quads are running. This will immediately replace crazyswarm/ros_ws/src/crazyswarm/launch/crazyflies.yaml, which is what is used in the final launch script.
Edit the launch script in crazyswarm/ros_ws/src/crazyswarm/launch/hover_swarm.launch Mainly, you need to specify motion_capture_type: "vicon", motion_capture_host_name: andobject_tracking_type: "motionCapture"` I also commented out the teleop and joy nodes that were in the script originally, but that is upto you.
Ensure vicon is running
Launch the launch script: roslaunch crazyswarm hover_swarm.launch You should see a rviz window pop up, and the the quad should be visible in it.

IN TERMINAL 2:

cd crazyswawm/ros_ws
source devel/setup.bash
cd src/crazyswarm/scripts
python3 niceHover.py

This should launch the drone, and make it hover!

Two Quad Figure of 8

update allcrazyflies.yaml appropriately and run python3 chooser.py to set the correct quads up.
source the ros_ws/devel/setup.py in each terminal.
In one terminal run roslaunch crazyswarm hover_launch.launch
In a second terminal run python3 figure_8_simple.py

notes:

It might be useful to figure out which channel is best: https://blog.crazyflie.net/?p=18

dasc-lab / crazyswarm