Giters
bdring
/
FluidNC
The next generation of motion control firmware
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
1420
Watchers:
72
Issues:
632
Forks:
345
bdring/FluidNC Issues
Problem: Web GUI unresponsive, Pendant have a blacscreen
Updated
7 days ago
Comments count
10
Problem with homing with 2 motor
Closed
11 days ago
Comments count
4
Second limit switch Y axis is not working properly
Updated
14 days ago
Comments count
6
Problem: FluidNC 6XCNC Controller - strange LED lights and steppers suddenly not working
Updated
14 days ago
Comments count
11
Problem: Probing seems to incorrectly affect machine Coordinates
Closed
16 days ago
Comments count
8
Problem: Some alarm conditions can disable the steppers, even with idle_ms set to 255
Updated
17 days ago
Alarm 14 may not be cleared if an axis is not set to home
Updated
17 days ago
Problem: how to home at hold state (by config file or programmatically)
Closed
20 days ago
Comments count
12
Problem: slow homing speed. `seek_mm_per_min` has no effect
Updated
22 days ago
Comments count
2
Wifi porblem
Closed
23 days ago
Comments count
1
Problem: Homing X in >3.7.10 not working on ESP32
Updated
24 days ago
Comments count
6
[MSG:ERR: Command requires idle state]
Closed
25 days ago
Comments count
4
Problem: All the TMC drivers not detected
Closed
25 days ago
Comments count
1
Feature: Trinamic position control via SPI
Closed
a month ago
Comments count
1
Problem: Installing the FluidNC on an esp32-s3
Updated
a month ago
Comments count
5
Problem: GPIO2 use for limit_neg_pin can't pu 3.3v only 0.31v
Closed
a month ago
Comments count
4
Problem: How to install FluidNC the esp32-s2 or esp32-c3.
Closed
a month ago
Comments count
1
Problem: TMC driver not detected after reinitialize, only one axis driver test passed at the beginning.
Updated
a month ago
Comments count
4
Abnormal operating speed
Closed
a month ago
Comments count
9
Error when re-initializing TMC 2209 stepper motors from version 3.7.15.
Closed
a month ago
Comments count
2
No movement
Updated
a month ago
Comments count
35
Problem: Keyboard jogging not working
Closed
a month ago
Comments count
2
Probe not working on 6x board or Wemos D1
Closed
2 months ago
Comments count
4
Problem: Inverting probe pin stopped working after 3.7.12
Closed
a month ago
Comments count
12
Unable to connect to Wifi
Closed
a month ago
Comments count
13
Feature: I also design a board for fluidnc, but I don't know if someone like this designed style?
Closed
2 months ago
Comments count
2
Problem: MKS DLC32 v2.1 error rst:0x10 (RTCWDT_RTC_RESET),boot:0x1b (SPI_FAST_FLASH_BOOT)
Closed
2 months ago
Comments count
9
Problem: XPRO v5 with Laser Head. Relay not switch on and PWM always 4.96V
Closed
2 months ago
Comments count
6
Problem: fluidterm Command cannot be entered
Closed
2 months ago
Comments count
1
Problem: v3.7.15 WiFi failed:406 wrong data
Closed
2 months ago
Comments count
4
MKS DLC32, PWM Spindle runs for a second on board reset.
Closed
2 months ago
Comments count
2
Fluid Dial only ever shows NC when connected to a 6-Pack Board
Closed
2 months ago
Comments count
31
Problem: Random homing fail from 3.7.7 onwards
Updated
2 months ago
Comments count
9
Problem:" $Files/ListGcode error" codes in response UART 1 & 2
Closed
2 months ago
Comments count
2
Problem: M5 will still report a spindle speed
Updated
2 months ago
Comments count
1
What is the size of serial Buffer ?
Closed
2 months ago
Comments count
2
Problem: Issues with uploading *.yaml to FluidNC (latest version)
Closed
3 months ago
Comments count
13
Problem: Fluidnc seems to respond to a jog command with the jog command itself on additional uart
Closed
3 months ago
Comments count
7
Feature: Folinn BD600 class in "Spindles" for RS485 support
Updated
3 months ago
Comments count
1
Problem: Fallback web page fails with 3.7.15
Closed
3 months ago
Comments count
2
Probe no more working after 3.7.13 Upgrade
Updated
3 months ago
Comments count
14
Problem: Failed to communicate with FW!
Updated
3 months ago
Comments count
4
Can't implement shared_fault_pin
Closed
3 months ago
Comments count
8
OTA update to v3.7.15 failed at 36%, threw an error in the WebUI. Rebooting then failed.
Closed
3 months ago
Comments count
14
Machine is not homing X
Closed
3 months ago
Comments count
9
Web interface bug
Updated
3 months ago
Comments count
2
Problem: Cannot configure an ssid which contains an exclamation mark
Closed
3 months ago
Comments count
2
Problem: Table pulling out of square after homing
Updated
3 months ago
Comments count
1
Add dual end stop support
Closed
3 months ago
Comments count
8
Backlash compensation
Updated
3 months ago
Previous
Next