meshnet CNI

meshnet is a (K8s) CNI plugin to create arbitrary network topologies out of point-to-point links with the help of koko. Heavily inspired by Ratchet-CNI, kokonet and Multus.

New in version 0.2.0

Using K8s etcd as datastore via Custom Resources
All internal communication now happens over gRPC
Support for macvlan links to connect to external resources

Architecture

The goal of this plugin is to interconnect pods via direct point-to-point links according to a pre-define topology. To do that, the plugin uses three types of links:

veth - used to connect two pods running on the same host
vxlan - used to connected two pods running on different hosts
- Optionally users can opt in to use gRPC instead, for this use case. Check Installation.
macvlan - used to connect to external resources, i.e. any physical or virtual device outside of the Kubernetes cluster

Topology information, represented as a list of links per pod, is stored in k8s's etcd datastore as custom resources:

apiVersion: networkop.co.uk/v1beta1
kind: Topology
metadata:
  name: r1
spec:
  links:
  - uid: 1
    peer_pod: r2
    local_intf: eth1
    local_ip: 12.12.12.1/24
    peer_intf: eth1
    peer_ip: 12.12.12.2/24

The plugin configuration file contains a "chained" meshnet in the list of plugins:

{
  "cniVersion": "0.3.1",
  "name": "kindnet",
  "plugins": [
    {
      "ipMasq": false,
      "ipam": {
        "dataDir": "/run/cni-ipam-state",
        "ranges": [
          [
            {
              "subnet": "10.244.0.0/24"
            }
          ]
        ],
        "routes": [
          {
            "dst": "0.0.0.0/0"
          }
        ],
        "type": "host-local"
      },
      "mtu": 1500,
      "type": "ptp"
    },
    {
      "capabilities": {
        "portMappings": true
      },
      "type": "portmap"
    },
    {
      "name": "meshnet",
      "type": "meshnet",
      "ipam": {},
      "dns": {}
    }
  ]
}

The plugin consists of three main components:

datastore - a k8s native etcd backend cluster storing topology information and runtime pod metadata (e.g. pod IP address and NetNS)
meshnet - a CNI binary responsible for pod's network configuration
meshnetd - a daemon responsible for communication with k8s and vxlan (or grpc) link configuration updates

Below is the order of operation of the plugin from the perspective of kube-node-1:

Kubernetes cluster gets populated with the topology information via custom resources
pod-1/pod-2 come up, local kubelet calls the meshnet binary for each pod to setup their networking.
Based on the CNI configuration file, Kubelet calls meshnet to set up additional interfaces.

Note that eth0 is always setup by one of the existing CNI plugins. It is used to provide external connectivity to and from the pod

meshnet binary updates the topology data with pod's runtime metadata (namespace filepath and primary IP address).
meshnet binary (via a local meshnet daemon) retrieves the list of links and looks up peer pod's metadata to identify what kind of link to setup - veth, vxlan or macvlan.
If the peer is on the same node, it calls koko to setup a veth link between the two pods.
If the peer is on the remote node, it does two things:
- 7.1 It calls koko to setup a local vxlan link.
- 7.2 It makes a gRPC Update call to the remote node's meshnet daemon, specifying this link's metadata (e.g. VTEP IP and VNI).
Upon receipt of this information, remote node's meshnetd idepmotently updates the local vxlan link, i.e. it creates a new link, updates the existing link if there's a change or does nothing if the link attributes are the same.

Local Demo

Clone this project and build a local 3-node Kubernetes cluster

make up

Build the meshnet-cni docker image

make docker

Install meshnet-cni plugin

# install meshnet with VXLAN link
make install
# or install meshnet with gRPC link
make grpc=1 install

Verify that meshnet is up and READY

kubectl get daemonset -n meshnet

Install a 3-node test topology

kubectl apply -f tests/3node.yml

Check that all pods are running

kubectl get pods -l test=3node                                                                  
NAME   READY   STATUS    RESTARTS   AGE
r1     1/1     Running   0          40m
r2     1/1     Running   0          40m
r3     1/1     Running   0          40s

Test connectivity between pods

kubectl exec r1 -- ping -c 1 12.12.12.2
kubectl exec r2 -- ping -c 1 23.23.23.3
kubectl exec r3 -- ping -c 1 13.13.13.1

Cleanup

kubectl delete --grace-period=0 --force -f tests/3node.yml

Destroy the local kind cluster

make down

Installation

The following manifest will create all that's required for meshnet plugin to function, i.e.:

A meshnet namespace
A Custom Resource Definition for network topologies
A set of RBAC rules to allow meshnet to interact with new custom resources
A daemonset with meshnet plugin and configuration files

# to install meshnet with VXLAN link
kubectl apply -k manifests/base
# to install meshnet with gRPC link
kubectl apply -k manifests/overlays/grpc-link

Interaction with existing resources

Meshnet plugin was designed to work alongside any other existing or future Kubernetes resources that may not require any special topology to be set up for them. Every pod coming up will have its first interface setup by an existing CNI plugin (e.g. flannel, weave, calico) and will only have additional interfaces connected if there's a matching custom Topology resource.

During the initial installation process, meshnet will try to insert itself into the list of CNI plugins. For example, assuming the following configuration is present in /etc/cni/net.d/weave.conf:

{
  "cniVersion": "0.2.0",
  "name": "weave",
  "type": "weave-net",
}

Meshnet will convert the above to conflist and produce the file /etc/cni/net.d/00-meshnet.conflist with the following content:

{
  "cniVersion": "0.2.0",
  "name": "weave",
  "plugins": [
    {
      "cniVersion": "0.2.0",
      "name": "weave",
      "type": "weave-net"
    },
    {
      "name": "meshnet",
      "type": "meshnet",
      "ipam": {},
      "dns": {}
    }
  ]
}

Customising installation paths

In some cases, Kubernetes distros may store CNI configuration files and binaries in non-standard directories and override them with --cni-bin-dir and --cni-conf-dir flags. In order to install meshnet into the right directories, create a new overlay under manifests/overlays and patch the cni-dir or cni-bin volumes with the correct location. See kops overlay for an example.

Resilient topologies

If you need to have Pods restarted and re-scheduled by the kube-controller, it's possible to deploy them as StatefulSets with replica number = 1. See this example.

Examples

Inside the tests directory there are 4 manifests with the following test topologies:

A simple point-to-point 2-node topology
A 3-node topology connected as a triangle
A 5-node topology connected as quincunx
A 2-node topology with 2nd node connected to a macvlan interface

Use k8s-topo to orchestrate network topologies

git clone https://github.com/networkop/k8s-topo.git && cd k8s-topo

Deploy k8s-topo pod

kubectl create -f manifest.yml

Connect to the k8s-topo pod

kubectl exec -it k8s-topo sh

Create a random 20-node network topology

./examples/builder/builder 20 0
Total number of links generated: 19

Create the topology inside K8s

k8s-topo --create examples/builder/random.yml

Optionally, you can generate a D3.js network topology graph

k8s-topo --graph examples/builder/random.yml

View the generated topology graph at http://<any_k8s_cluster_node_ip>:32000

Verify that the topology has been deployed (from the master node)

kubectl get pods -o wide | grep qrtr
qrtr-1     1/1     Running   0          11s     10.233.65.231   node3   <none>
qrtr-10    1/1     Running   0          11s     10.233.65.234   node3   <none>
qrtr-11    1/1     Running   0          10s     10.233.66.246   node4   <none>

$ qrtr-1
/ # for i in `seq 0 20`; do echo "192.0.2.$i =>"  $(ping -c 1 -W 1 192.0.2.$i|grep loss); done
192.0.2.0 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.1 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.2 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.3 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.4 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.5 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.6 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.7 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.8 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.9 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.10 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.11 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.12 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.13 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.14 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.15 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.16 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.17 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.18 => 1 packets transmitted, 1 packets received, 0% packet loss
192.0.2.19 => 1 packets transmitted, 1 packets received, 0% packet loss

Destroy the topology

k8s-topo --destroy examples/builder/random.yml

Troubleshooting

There are two places to collect meshnet logs:

Meshnet daemon logs can be collected outside of the Kubernetes cluster. For example, the below command will collect logs from all meshnet daemons using stern

stern meshnet -n meshnet

Meshnet plugin (binary) logs can be collected on the respective Kubernetes nodes, e.g.

root@kind-worker:/# journalctl -u kubelet

Each POD is supposed to run an init-wait container that waits for the right number of interface to be connected before passing the ball to the main container. However, sometimes, PODs restart resulting in the missing interfaces inside the main container process, since they may have been added AFTER the process that reads the container interface list (e.g. qemu-kvm for VM-based containers). This is the procedure I use to identify the cause of the failure:

Identify which POD is at fault. This will most likely be the incorrect number of interfaces.
Identify which interface is missing or was added last.
Identify the correlation between the pair of containers interconnected by the missing interface
Look for the peer container's failures using kubectl get events --sort-by=.metadata.creationTimestamp'
Identify which k8s node this POD is running on kubectl get pods acme-scs1001-a -o yaml | grep node
On that node check the journalctl for any errors associated with the POD

y-young / meshnet-cni