Snapraid AIO Script
The definitive all-in-one SnapRAID script. I hope you'll agree :).
There are many SnapRAID scripts out there, but none has the features I want. So I made my own, inspired by existing solutions.
It is meant to be run periodically (daily), do the heavy lifting and send an email you will actually read.
Supports single and dual parity configurations. It is highly customizable and has been tested with Debian 10/11 and OpenMediaVault 5/6.
Contributions are welcome!
Table of Contents
Highlights
How it works
- After some preliminary checks, the script will execute
snapraid diff
to figure out if parity info is out of date, which means checking for changes since the last execution. During this step, the script will ensure drives are fine by reading parity and content files. - One of the following will happen:
- If parity info is out of sync and the number of deleted or changed files exceed the threshold you have configured it stops. You may want to take a look to the output log.
- If parity info is out of sync and the number of deleted or changed files exceed the threshold, you can still force a sync after a number of warnings. It's useful If you often get a false alarm but you're confident enough. This is called "Sync with threshold warnings"
- Instead of forcing a sync based on the number of deleted files, you may consider the
ADD_DEL_THRESHOLD
feature, by allowing a sync that would otherwise violate the delete threshold, if the ratio of added to deleted files is greater than the value set.
- Instead of forcing a sync based on the number of deleted files, you may consider the
- If parity info is out of sync but the number of deleted or changed files did not exceed the threshold, it executes a sync to update the parity info.
- When the parity info is in sync, either because nothing has changed or after a successfully sync, it runs the
snapraid scrub
command to validate the integrity of the data, both the files and the parity info. If sync was cancelled or other issues were found, scrub will not be run.- Note that each run of the scrub command will validate only a configurable portion of parity info to avoid having a long running job and affecting the performance of the server.
- Scrub frequency can also be customized in case you don't want to do it every time the script runs.
- It is still recommended to run scrub frequently.
- Extra information can be added, like SnapRAID's disk health report or SnapRAID array status.
- When the script is done sends an email with the results, both in case of error or success, and triggers any 3rd party notifications configured.
Additional Information
- Docker container management
- Manage containers before SnapRAID operations and restore them when finished. It avoids nasty errors aboud data being written during SnapRAID sync.
- Support for local or remote Docker instances. Also manage multiple remote Docker instances at once.
- Note: Remote Docker instances require SSH passwordless access.
- You can either choose to pause or stop your containers.
- Custom Hooks
- Define shell commands or scripts to run before and after SnapRAID operations.
- 3rd Party notification support
- Healthchecks.io, Telegram and Discord can be used to track script execution time, status and promptly alert about errors.
- Notification Hook: if your favourite notification service is not supported by this script, you can use a custom notification command or even another mail binary
- Important messages are also sent to the system log.
- Emails are still the best place to get detailed but readable information.
Customization
Many options can be changed to your taste, their behavior is documented in the config file. If you don't know what to do, I recommend using the default values and see how it performs.
Customizable features
- Sync options
- Sync always (forced sync).
- Sync after a number of breached threshold warnings.
- Sync only if thresholds warnings are not breached (enabled by default).
- Sync even if the delete threshold has been breached, but the ratio of added to deleted files is greater than the value set.
- User definable thresholds for deleted and updated files.
- Scrub options
- Enable or disable scrub job.
- Delayed option, disabled by default. Run scrub only after a number of script executions, e.g. every 7 times. If you don't want to scrub your array every time, this one is for you.
- Data to be scrubbed - by default 5% older than 10 days.
- Scrub new data - scrub the data that was just added by the sync.
- Pre-hashing - enabled by default. Mitigate the lack of ECC memory, reading data twice to avoid silent read errors.
- Force zero size sync - disabled by default. Forces the operation of syncing a file with zero size that before was not. Use with caution!
- Snapraid Status - shows the status of the array, disabled by default.
- SMART Log - enabled by default. A SnapRAID report for disks health status.
- Verbosity option - disabled by default. When enabled, includes the TOUCH and DIFF commands output. Please note email will be huge and mostly unreadable.
- SnapRAID Output (log) retention - disabled by default (log is overriden every run)
- Detailed output retention for each run
- You can choose the amount of days and the path, by default set to the user home
- Healthchecks.io, Telegram and Discord integration
- If you don't read your emails every day, this is a great one for you, since you can be quickly informed if things go wrong.
- The script will report to Healthchecks.io, Telegram and Discord when is started and when is completed. If there's a failure it's included as well.
- Healthchecks.io only: If the script ends with a WARNING message, it will report DOWN to Healthchecks.io, if the message is COMPLETED it will report UP.
- Healthchecks.io only: This service will also show how much time the script takes to complete.
- Notification Hook
- Made for external services or mail binaries with different commands than
mailx
. - Configure the path of the script or the mail binary to be invoked.
- You can still use native services since it only replaces the standard email.
- Made for external services or mail binaries with different commands than
- Docker Container management
- A list of containers you want to be interrupted before running actions and restored when completed.
- Docker mode - choose to pause/unpause or to stop/restart your containers
- Docker remote - if docker is running on a remote machine
- Docker remote action delay - Set by default to 10 seconds, reduces errors when using remote docker
- Custom Hooks
- Commands or scripts to be run before and after SnapRAID operations.
- Option to display friendly name to in the email output
- Spindown - spindown disks after the script has completed operations. Uses a rewritten version of hd-idle.
You can also change more advanced options such SnapRAID binary location, log file location and mail binary. If your mail binary uses different commands than mailx
, use the Notification Hook feature.
A nice email report
This script produces emails that don't contain a list of changed files to improve clarity.
You can re-enable full output in the email by switching the option VERBOSITY
. The full report is available in /tmp/snapRAID.out
but will be replaced after each run, or deleted when the system is shut down. You can enable the retention policy to keep logs for some days and customize the folder location.
Here's an example email report.
## [COMPLETED] DIFF + SYNC + SCRUB Jobs (SnapRAID on omv-test.local)
SnapRAID Script Job started [Tue 20 Apr 11:43:37 CEST 2021]
Running SnapRAID version 11.5
SnapRAID AIO Script version X.YZ
----------
## Preprocessing
Healthchecks.io integration is enabled.
Configuration file found.
Checking if all parity and content files are present.
All parity files found.
All content files found.
Docker containers management is enabled.
### Stopping Containers [Tue 20 Apr 11:43:37 CEST 2021]
Stopping Container - Code-server
code-server
Stopping Container - Portainer
portainer
----------
## Processing
### SnapRAID TOUCH [Tue 20 Apr 11:43:37 CEST 2021]
Checking for zero sub-second files.
No zero sub-second timestamp files found.
TOUCH finished [Tue 20 Apr 11:43:38 CEST 2021]
### SnapRAID DIFF [Tue 20 Apr 11:43:38 CEST 2021]
DIFF finished [Tue 20 Apr 11:43:38 CEST 2021]
**SUMMARY of changes - Added [0] - Deleted [0] - Moved [0] - Copied [0] - Updated [1]**
There are no deleted files, that's fine.
There are updated files. The number of updated files (1) is below the threshold of (500).
SYNC is authorized. [Tue 20 Apr 11:43:38 CEST 2021]
### SnapRAID SYNC [Tue 20 Apr 11:43:38 CEST 2021]
Self test...
Loading state from /srv/dev-disk-by-label-DISK1/snapraid.content...
Scanning disk DATA1...
Scanning disk DATA2...
Using 0 MiB of memory for the file-system.
Initializing...
Hashing...
SYNC - Everything OK
Resizing...
Saving state to /srv/dev-disk-by-label-DISK1/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK2/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK3/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK4/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK1/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK2/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK3/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK4/snapraid.content...
Verified /srv/dev-disk-by-label-DISK4/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK3/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK2/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK1/snapraid.content in 0 seconds
Syncing...
Using 32 MiB of memory for 32 cached blocks.
DATA1 12% | *******
DATA2 82% | ************************************************
parity 0% |
2-parity 0% |
raid 1% | *
hash 1% |
sched 11% | ******
misc 0% |
|____________________________________________________________
wait time (total, less is better)
SYNC - Everything OK
Saving state to /srv/dev-disk-by-label-DISK1/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK2/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK3/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK4/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK1/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK2/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK3/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK4/snapraid.content...
Verified /srv/dev-disk-by-label-DISK4/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK3/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK2/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK1/snapraid.content in 0 seconds
SYNC finished [Tue 20 Apr 11:43:40 CEST 2021]
### SnapRAID SCRUB [Tue 20 Apr 11:43:40 CEST 2021]
Self test...
Loading state from /srv/dev-disk-by-label-DISK1/snapraid.content...
Using 0 MiB of memory for the file-system.
Initializing...
Scrubbing...
Using 48 MiB of memory for 32 cached blocks.
DATA1 2% | *
DATA2 18% | **********
parity 0% |
2-parity 0% |
raid 21% | ************
hash 7% | ****
sched 51% | ******************************
misc 0% |
|____________________________________________________________
wait time (total, less is better)
SCRUB - Everything OK
Saving state to /srv/dev-disk-by-label-DISK1/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK2/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK3/snapraid.content...
Saving state to /srv/dev-disk-by-label-DISK4/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK1/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK2/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK3/snapraid.content...
Verifying /srv/dev-disk-by-label-DISK4/snapraid.content...
Verified /srv/dev-disk-by-label-DISK4/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK3/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK2/snapraid.content in 0 seconds
Verified /srv/dev-disk-by-label-DISK1/snapraid.content in 0 seconds
SCRUB finished [Tue 20 Apr 11:43:41 CEST 2021]
----------
## Postprocessing
SnapRAID Smart
SnapRAID SMART report:
Temp Power Error FP Size
C OnDays Count TB Serial Device Disk
- - - SSD 0.0 00000000000000000001 /dev/sdb DATA1
- - - SSD 0.0 01000000000000000001 /dev/sdc DATA2
- - - - 0.0 02000000000000000001 /dev/sdd parity
- - - SSD 0.0 03000000000000000001 /dev/sde 2-parity
- - - n/a - - /dev/sr0 -
0 - - - 0.0 - /dev/sda -
The FP column is the estimated probability (in percentage) that the disk
is going to fail in the next year.
Probability that at least one disk is going to fail in the next year is 0%.
## Restarting Containers [Tue 20 Apr 11:43:41 CEST 2021]
Restarting Container - Code-server
code-server
Restarting Container - Portainer
portainer
All jobs ended. [Tue 20 Apr 11:43:41 CEST 2021]
Email address is set. Sending email report to yourmail@example.com [Tue 20 Apr 11:43:41 CEST 2021]
Requirements
markdown
to format emails - will be installed if not foundcurl
to use Healhchecks - will be installed if not foundhd-idle
to spin down disks - Link, installation instructions below
Installation
Optional: install markdown apt install python-markdown
and curl apt install curl
. You can skip this step since the script will try to install missing packages for you.
- Download the latest version from Releases
- Extract the archive wherever you prefer
- e.g.
/usr/sbin/snapraid
- e.g.
- Give executable rights to the main script
chmod +x snapraid-aio-script.sh
- Open the config file and make changes to the config file as required.
- Every config is documented but defaults are pretty resonable, so don't make changes if you're not sure.
- When you see
""
or''
in some options, do not remove these characters but just fill in your data. - If you want to spindown your disks, you need to install hd-idle
- Schedule the script execution.
- I recommend running the script daily.
It is tested on OMV5/6, but will work on other distros. In such case you may have to change the mail binary or SnapRAID location.
First Run
If you start with empty disks, you cannot use (yet) this script, since it expects SnapRAID files which would not be found.
First run snapraid sync
. Once completed, the array will be ready to be used with this script.
OMV5/6 and SnapRAID plugin
Ignore what you see at OMV GUI > Services > SnapRAID > Diff Script Settings, since it only applies to the plugin's built-in script. Also don't forget to remove the built-in omv-snapraid-diff
job from OMV GUI > System > Scheduled Tasks, either by deleting the job, or simply disabling it.
hd-idle
for Automatic Disk Spindown
Installing If you would like to enable automatic disk spindown after the script job runs, then you will need to install hd-idle
. The version included in default Debian and Ubuntu repositories is buggy and out of date - fortunately developer adelolmo has improved the project and released an updated version.
NOTE: This script is NOT compatible with the hd-idle
version found in the Debian repositories. You must use the updated hd-idle
binaries for spindown to work. If you receive and error such as hd-idle cannot spindown scsi disk /dev//dev/sda:
then that is a sign that you are using the old/buggy version. Follow the instructions below to update.
- Remove any previously existing versions of
hd-idle
, either by manually removing the binaries, or runningapt remove hd-idle
to remove the version from the default respositories. - For all recent Ubuntu and Debian releases, install the developers's repository using instructions on the developer's website. The command snippet below will select the correct repository based on your current release, and add it to your apt sources.
sudo apt-get install apt-transport-https
wget -O - http://adelolmo.github.io/andoni.delolmo@gmail.com.gpg.key | sudo apt-key add -
echo "deb http://adelolmo.github.io/$(lsb_release -cs) $(lsb_release -cs) main" | sudo tee /etc/apt/sources.list.d/adelolmo.github.io.list
- Run
apt update
, andapt install hd-idle
to install the updated version. You do not need to specify the respository, apt will automatically install the newset version from the new repository. - In your
script-config.sh
file, changeSPINDOWN=0
toSPINDOWN=1
to enable spindown. - If you wish to use
hd-idle
as a service to manage your disks outside of the scope of the Snapraid AIO Script, refer to these additional instructions on the OpenMediaVault forum.
Upgrade
If you are using a previous version of the script, do not use your config file. Please move your preferences to the new script-config.sh
found in the archive.
Known Issues
- You tell me!
Credits
All rights belong to the respective creators. This script would not exist without: