todbot / circuitpython-tricks

Some CircuitPython tricks, mostly reminders to myself

Geek Repo:Geek Repo

Github PK Tool:Github PK Tool

circuitpython-tricks

A small list of tips & tricks I find myself needing when working with CircuitPython. I find these examples useful when picking up a new project and I just want some boilerplate to get started. Also see the circuitpython-tricks/larger-tricks directory for additional ideas.

An older version of this page is a Learn Guide on Adafruit too!

If you're new to CircuitPython overall, there's no single reference, but:

Table of Contents

But it's probably easiest to do a Cmd-F/Ctrl-F find on keyword of idea you want.

Inputs

Read a digital input as a Button

import board
from digitalio import DigitalInOut, Pull
button = DigitalInOut(board.D3) # defaults to input
button.pull = Pull.UP # turn on internal pull-up resistor
print(button.value)  # False == pressed

Can also do:

import time, board, digitalio
button = digitalio.DigitalInOut(board.D3)
button.switch_to_input(digitalio.Pull.UP)
while True:
    print("button pressed:", button.value == False) # False == pressed
    time.sleep(0.1)

Read a Potentiometer

import board
import analogio
potknob = analogio.AnalogIn(board.A1)
position = potknob.value  # ranges from 0-65535
pos = potknob.value // 256  # make 0-255 range

Note: While AnalogIn.value is 16-bit (0-65535) corresponding to 0 V to 3.3V, the MCU ADCs can have limitations in resolution and voltage range. This reduces what CircuitPython sees. For example, the ESP32 ADCs are 12-bit w/ approx 0.1 V to 2.5 V range (e.g. value goes from around 200 to 50,000, in steps of 16)

Read a Touch Pin / Capsense

import touchio
import board
touch_pin = touchio.TouchIn(board.GP6)
# on Pico / RP2040, need 1M pull-down on each input
if touch_pin.value:
print("touched!")

Read a Rotary Encoder

import board
import rotaryio
encoder = rotaryio.IncrementalEncoder(board.GP0, board.GP1) # must be consecutive on Pico
print(encoder.position)  # starts at zero, goes neg or pos

Debounce a pin / button

import board
from digitalio import DigitalInOut, Pull
from adafruit_debouncer import Debouncer
button_in = DigitalInOut(board.D3) # defaults to input
button_in.pull = Pull.UP # turn on internal pull-up resistor
button = Debouncer(button_in)
while True:
    button.update()
    if button.fell:
        print("press!")
    if button.rose:
      print("release!")

Note: Most boards have the native keypad module that can do keypad debouncing in a much more efficient way. See Set up and debounce a list of pins

Detect button double-click

import board
from digitalio import DigitalInOut, Pull
from adafruit_debouncer import Button
button_in = DigitalInOut(board.D3) # defaults to input
button_in.switch_to_input(Pull.UP) # turn on internal pull-up resistor
button = Button(button_in)
while True:
    button.update()
    if button.pressed:
        print("press!")
    if button.released:
      print("release!")
    if button.short_count > 1:  # detect multi-click
      print("multi-click: click count:", button.short_count)

Set up and debounce a list of pins

If your board's CircuitPython has the keypad library (most do), then I recommend using it. It's not just for key matrixes! And it's more efficient and, since it's built-in, reduces a library dependency.

import board
import keypad
button_pins = (board.GP0, board.GP1, board.GP2, board.GP3, board.GP4)
buttons = keypad.Keys(button_pins, value_when_pressed=False, pull=True)

while True:
    button = buttons.events.get()  # see if there are any key events
    if button:                      # there are events!
      if button.pressed:
        print("button", button.key_number, "pressed!")
      if button.released:
        print("button", button.key_number, "released!")

Otherwise, you can use adafruit_debouncer:

import board
from digitalio import DigitalInOut, Pull
from adafruit_debouncer import Debouncer
button_pins = (board.GP0, board.GP1, board.GP2, board.GP3, board.GP4)
buttons = []   # will hold list of Debouncer objects
for pin in button_pins:   # set up each pin
    tmp_pin = DigitalInOut(pin) # defaults to input
    tmp_pin.pull = Pull.UP      # turn on internal pull-up resistor
    buttons.append( Debouncer(tmp_pin) )
while True:
    for i in range(len(buttons)):
        buttons[i].update()
        if buttons[i].fell:
            print("button",i,"pressed!")
        if buttons[i].rose:
            print("button",i,"released!")

Outputs

Output HIGH / LOW on a pin (like an LED)

import board
import digitalio
ledpin = digitalio.DigitalInOut(board.D2)
ledpin.direction = digitalio.Direction.OUTPUT
ledpin.value = True

Can also do:

ledpin = digitalio.DigitalInOut(board.D2)
ledpin.switch_to_output(value=True)

Output Analog value on a DAC pin

Different boards have DAC on different pins

import board
import analogio
dac = analogio.AnalogOut(board.A0)  # on Trinket M0 & QT Py
dac.value = 32768   # mid-point of 0-65535

Output a "Analog" value on a PWM pin

import board
import pwmio
out1 = pwmio.PWMOut(board.MOSI, frequency=25000, duty_cycle=0)
out1.duty_cycle = 32768  # mid-point 0-65535 = 50 % duty-cycle

Control Neopixel / WS2812 LEDs

import neopixel
leds = neopixel.NeoPixel(board.NEOPIXEL, 16, brightness=0.2)
leds[0] = 0xff00ff  # first LED of 16 defined
leds[0] = (255,0,255)  # equivalent
leds.fill( 0x00ff00 )  # set all to green

Control a servo, with animation list

# servo_animation_code.py -- show simple servo animation list
import time, random, board
from pwmio import PWMOut
from adafruit_motor import servo

# your servo will likely have different min_pulse & max_pulse settings
servoA = servo.Servo(PWMOut(board.RX, frequency=50), min_pulse=500, max_pulse=2250)

# the animation to play
animation = (
    # (angle, time to stay at that angle)
    (0, 2.0),
    (90, 2.0),
    (120, 2.0),
    (180, 2.0)
)
ani_pos = 0 # where in list to start our animation

while True:
    angle, secs = animation[ ani_pos ]
    print("servo moving to", angle, secs)
    servoA.angle = angle
    time.sleep( secs )
    ani_pos = (ani_pos + 1) % len(animation) # go to next, loop if at end

Neopixels / Dotstars

Moving rainbow on built-in board.NEOPIXEL

In CircuitPython 7, the rainbowio module has a colorwheel() function. Unfortunately, the rainbowio module is not available in all builds. In CircuitPython 6, colorwheel() is a built-in function part of _pixelbuf or adafruit_pypixelbuf.

The colorwheel() function takes a single value 0-255 hue and returns an (R,G,B) tuple given a single 0-255 hue. It's not a full HSV_to_RGB() function but often all you need is "hue to RGB", wher you assume saturation=255 and value=255. It can be used with neopixel, adafruit_dotstar, or any place you need a (R,G,B) 3-byte tuple. Here's one way to use it.

# CircuitPython 7 with or without rainbowio module
import time, board, neopixel
try:
    from rainbowio import colorwheel
except:
    def colorwheel(pos):
        if pos < 0 or pos > 255:  return (0, 0, 0)
        if pos < 85: return (255 - pos * 3, pos * 3, 0)
        if pos < 170: pos -= 85; return (0, 255 - pos * 3, pos * 3)
        pos -= 170; return (pos * 3, 0, 255 - pos * 3)

led = neopixel.NeoPixel(board.NEOPIXEL, 1, brightness=0.4)
while True:
    led.fill( colorwheel((time.monotonic()*50)%255) )
    time.sleep(0.05)

Make moving rainbow gradient across LED strip

See demo of it in this tweet.

import time, board, neopixel, rainbowio
num_leds = 16
leds = neopixel.NeoPixel(board.D2, num_leds, brightness=0.4, auto_write=False )
delta_hue = 256//num_leds
speed = 10  # higher numbers = faster rainbow spinning
i=0
while True:
  for l in range(len(leds)):
    leds[l] = rainbowio.colorwheel( int(i*speed + l * delta_hue) % 255  )
  leds.show()  # only write to LEDs after updating them all
  i = (i+1) % 255
  time.sleep(0.05)

A shorter version using a Python list comprehension. The leds[:] trick is a way to assign a new list of colors to all the LEDs at once.

import supervisor, board, neopixel, rainbowio
num_leds = 16
speed = 10  # lower is faster, higher is slower
leds = neopixel.NeoPixel(board.D2, 16, brightness=0.4)
while True:
  t = supervisor.ticks_ms() / speed
  leds[:] = [rainbowio.colorwheel( t + i*(255/len(leds)) ) for i in range(len(leds))]

Fade all LEDs by amount for chase effects

import time
import board, neopixel
num_leds = 16
leds = neopixel.NeoPixel(board.D2, num_leds, brightness=0.4, auto_write=False )
my_color = (55,200,230)
dim_by = 20  # dim amount, higher = shorter tails
pos = 0
while True:
  leds[pos] = my_color
  leds[:] = [[max(i-dim_by,0) for i in l] for l in leds] # dim all by (dim_by,dim_by,dim_by)
  pos = (pos+1) % num_leds  # move to next position
  leds.show()  # only write to LEDs after updating them all
  time.sleep(0.05)

Audio

In CircuitPython, there are three different techniques to output audio:

  • audioio -- uses built-in DAC
  • audiopwmio -- uses PWM like arduino analogWrite(), requires RC filter to convert to analog
  • audiobusio -- output I2S data stream, requires external I2S decoder hardware

CircuitPython's support on particular microcontroller may include support for more than one of the above:

  • e.g. SAMD51 (Feather M4) supports DAC and I2S, RP2040 (Pico) supports PWM and I2S

CircuitPython can play WAV and MP3 files, but they must be formatted correctly.

See Preparing Audio Files for CircuitPython

Audio out using PWM

This uses the audiopwmio library, only available for Raspberry Pi Pico (or other RP2040-based boards) and NRF52840-based boards like Adafruit Feather nRF52840 Express. On RP2040-based boards, any pin can be PWM Audio pin. See the audiopwomio Support Matrix for which boards support audiopwmio.

import time, board
from audiocore import WaveFile
from audiopwmio import PWMAudioOut as AudioOut
wave_file = open("laser2.wav", "rb")
wave = WaveFile(wave_file)
audio = AudioOut(board.TX) # must be PWM-capable pin
while True:
    print("audio is playing:",audio.playing)
    if not audio.playing:
      audio.play(wave)
      wave.sample_rate = int(wave.sample_rate * 0.90) # play 10% slower each time
    time.sleep(0.1)

Note: Sometimes the audiopwmio driver gets confused, particularly if there's other USB access, so you may have to reset the board to get PWM audio to work again.

Note: PWM output must be filtered and converted to line-level to be usable. Use an RC circuit to accomplish this, see this twitter thread for details.

Audio out using DAC

Some CircuitPython boards (SAMD51 "M4" & SAMD21 "M0") have built-in DACs that are supported. The code is the the same as above, with just the import line changing. See the audioio Support Matrix for which boards support audioio.

import time, board
import audiocore, audioio # DAC
wave_file = open("laser2.wav", "rb")
wave = audiocore.WaveFile(wave_file)
audio = audioio.AudioOut(board.A0)  # must be DAC-capable pin, A0 on QTPy Haxpress
while True:
  print("audio is playing:",audio.playing)
  if not audio.playing:
    audio.play(wave)
    wave.sample_rate = int(wave.sample_rate * 0.90) # play 10% slower each time
  time.sleep(0.1)

Audio out using I2S

Unlike PWM or DAC, most CircuitPython boards support driving an external I2S audio board. This will also give you higher-quality sound output than DAC or PWM. See the audiobusio Support Matrix for which boards support audiobusio.

# for e.g. Pico RP2040 pins bit_clock & word_select pins must be adjacent
import board, audiobusio, audiocore
audio = audiobusio.I2SOut(bit_clock=board.GP0, word_select=board.GP1, data=board.GP2)
audio.play( audiocore.WaveFile("laser2.wav","rb") )

Use audiomixer to prevent audio crackles

The default buffer used by the audio system is quite small. This means you'll hear corrupted audio if CircuitPython is doing anything else (having CIRCUITPY written to, updating a display). To get around this, you can use audiomixer to make the audio buffer larger. Try buffer_size=2048 to start. A larger buffer means a longer lag between when a sound is triggered when its heard.

import time, board
from audiocore import WaveFile
from audioio import AudioOut
import audiomixer
wave = WaveFile(open("laser2.wav", "rb"))
audio = AudioOut(board.A0) # assuming QTPy M0 or Itsy M4
mixer = audiomixer.Mixer(voice_count=1, sample_rate=22050, channel_count=1,
                         bits_per_sample=16, samples_signed=True, buffer_size=2048)
audio.play(mixer)  # never touch "audio" after this, use "mixer"
while True:
    print("mixer voice is playing:", mixer.voice[0].playing)
    if not mixer.voice[0].playing:
      time.sleep(1)
      print("playing again")
      mixer.voice[0].play(wave)
    time.sleep(0.1)

Play multiple sounds with audiomixer

This example assumes WAVs that are mono 22050 Hz sample rate, w/ signed 16-bit samples.

import time, board, audiocore, audiomixer
from audiopwmio import PWMAudioOut as AudioOut

wav_files = ("loop1.wav", "loop2.wav", "loop3.wav")
wavs = [None] * len(wav_files)  # holds the loaded WAVs

audio = AudioOut(board.GP2)  # RP2040 example
mixer = audiomixer.Mixer(voice_count=len(wav_files), sample_rate=22050, channel_count=1,
                         bits_per_sample=16, samples_signed=True, buffer_size=2048)
audio.play(mixer)  # attach mixer to audio playback

for i in range(len(wav_files)):
    print("i:",i)
    wavs[i] = audiocore.WaveFile(open(wav_files[i], "rb"))
    mixer.voice[i].play( wavs[i], loop=True) # start each one playing

while True:
    print("doing something else while all loops play")
    time.sleep(1)

Note: M0 boards do not have audiomixer

Note: Number of simultaneous sounds is limited sample rate and flash read speed. Rules of thumb:

  • Built-in flash: 10 22kHz sounds simultanously
  • SPI SD cards: 2 22kHz sounds simultaneously

Also see the many examples in larger-tricks.

Playing MP3 files

Once you have set up audio output (either directly or via AudioMixer), you can play WAVs or MP3s through it, or play both simultaneously.

For instance, here's an example that uses an I2SOut to a PCM5102 on a Raspberry Pi Pico RP2040 to simultaneously play both a WAV and an MP3:

import board, audiobusio, audiocore, audiomp3
num_voices = 2

i2s_bclk, i2s_wsel, i2s_data = board.GP9, board.GP10, board.GP11 # BCLK, LCLK, DIN on PCM5102

audio = audiobusio.I2SOut(bit_clock=i2s_bclk, word_select=i2s_wsel, data=i2s_data)
mixer = audiomixer.Mixer(voice_count=num_voices, sample_rate=22050, channel_count=1,
                         bits_per_sample=16, samples_signed=True)
audio.play(mixer) # attach mixer to audio playback

wav_file = "/amen1_22k_s16.wav" # in 'circuitpython-tricks/larger-tricks/breakbeat_wavs'
mp3_file = "/vocalchops476663_22k_128k.mp3" # in 'circuitpython-tricks/larger-tricks/wav'
# https://freesound.org/people/f-r-a-g-i-l-e/sounds/476663/

wave = audiocore.WaveFile(open(wav_file, "rb"))
mp3 = audiomp3.MP3Decoder(open(mp3_file, "rb"))
mixer.voice[0].play( wave )
mixer.voice[1].play( mp3 )

while True:
    pass   # both audio files play

Note: For MP3 files, be aware that since this is doing software MP3 decoding, you will likely need to re-encode the MP3s to lower bitrate and sample rate (max 128 kbps and 22,050 Hz) to be playable the lower-end CircuitPython devices like the Pico / RP2040.

Note: For MP3 files and setting loop=True when playing, there is a small delay when looping. WAV files loop seemlessly.

Making simple tones

For devices that only have pwmio capability, you can make simple tones. The simpleio library can be used for this:

# a short piezo song using tone()
import time, board, simpleio
while True:
    for f in (262, 294, 330, 349, 392, 440, 494, 523):
        simpleio.tone(board.A0, f, 0.25)
    time.sleep(1)

An example of boards with pwmio but no audio are ESP32-S2-based boards like FunHouse, where you cannot play WAV files, but you can make beeps. A larger example is this gist: https://gist.github.com/todbot/f35bb5ceed013a277688b2ca333244d5

USB

Rename CIRCUITPY drive to something new

For instance, if you have multiple of the same device. The label can be up to 11 characters. This goes in boot.py not code.py and you must powercycle board.

# this goes in boot.py not code.py!
new_name = "TRINKEYPY0"
import storage
storage.remount("/", readonly=False)
m = storage.getmount("/")
m.label = new_name
storage.remount("/", readonly=True)

Detect if USB is connected or not

import supervisor
if supervisor.runtime.usb_connected:
  led.value = True   # USB
else:
  led.value = False  # no USB

An older way that tries to mount CIRCUITPY read-write and if it fails, USB connected:

def is_usb_connected():
    import storage
    try:
        storage.remount('/', readonly=False)  # attempt to mount readwrite
        storage.remount('/', readonly=True)  # attempt to mount readonly
    except RuntimeError as e:
        return True
    return False
is_usb = "USB" if is_usb_connected() else "NO USB"
print("USB:", is_usb)

Get CIRCUITPY disk size and free space

import os
fs_stat = os.statvfs('/')
print("Disk size in MB", fs_stat[0] * fs_stat[2] / 1024 / 1024)
print("Free space in MB", fs_stat[0] * fs_stat[3] / 1024 / 1024)

Programmatically reset to UF2 bootloader

import microcontroller
microcontroller.on_next_reset(microcontroller.RunMode.UF2)
microcontroller.reset()

Note: in older CircuitPython use RunMode.BOOTLOADER and for boards with multiple bootloaders (like ESP32-S2):

import microcontroller
microcontroller.on_next_reset(microcontroller.RunMode.BOOTLOADER)
microcontroller.reset()

USB Serial

Print to USB Serial

print("hello there")  # prints a newline
print("waiting...", end='')   # does not print newline
for i in range(256):  print(i, end=', ')   # comma-separated numbers

Read user input from USB Serial, blocking

while True:
    print("Type something: ", end='')
    my_str = input()  # type and press ENTER or RETURN
    print("You entered: ", my_str)

Read user input from USB Serial, non-blocking (mostly)

import time
import supervisor
print("Type something when you're ready")
last_time = time.monotonic()
while True:
    if supervisor.runtime.serial_bytes_available:
        my_str = input()
        print("You entered:", my_str)
    if time.monotonic() - last_time > 1:  # every second, print
        last_time = time.monotonic()
        print(int(last_time),"waiting...")

Read keys from USB Serial

import time, sys, supervisor
print("type charactcers")
while True:
    n = supervisor.runtime.serial_bytes_available
    if n > 0:  # we read something!
        s = sys.stdin.read(n)  # actually read it in
        # print both text & hex version of recv'd chars (see control chars!)
        print("got:", " ".join("{:s} {:02x}".format(c,ord(c)) for c in s))
    time.sleep(0.01) # do something else

Read user input from USB serial, non-blocking

class USBSerialReader:
    """ Read a line from USB Serial (up to end_char), non-blocking, with optional echo """
    def __init__(self):
        self.s = ''
    def read(self,end_char='\n', echo=True):
        import sys, supervisor
        n = supervisor.runtime.serial_bytes_available
        if n > 0:                    # we got bytes!
            s = sys.stdin.read(n)    # actually read it in
            if echo: sys.stdout.write(s)  # echo back to human
            self.s = self.s + s      # keep building the string up
            if s.endswith(end_char): # got our end_char!
                rstr = self.s        # save for return
                self.s = ''          # reset str to beginning
                return rstr
        return None                  # no end_char yet

usb_reader = USBSerialReader()
print("type something and press the end_char")
while True:
    mystr = usb_reader.read()  # read until newline, echo back chars
    #mystr = usb_reader.read(end_char='\t', echo=False) # trigger on tab, no echo
    if mystr:
        print("got:",mystr)
    time.sleep(0.01)  # do something time critical

USB MIDI

CircuitPython can be a MIDI controller, or respond to MIDI! Adafruit provides an adafruit_midi class to make things easier, but it's rather complex for how simple MIDI actually is. So for outputting MIDI, you can opt to just do raw bytearrays. For reading MIDI, I recommend Winterbloom's SmolMIDI.

Sending MIDI with adafruit_midi

import usb_midi
import adafruit_midi
from adafruit_midi.note_on import NoteOn
from adafruit_midi.note_off import NoteOff
midi_out_channel = 3 # human version of MIDI out channel (1-16)
midi = adafruit_midi.MIDI( midi_out=usb_midi.ports[1], out_channel=midi_out_channel-1)

def play_note(note,velocity=127):
    midi.send(NoteOn(note, velocity))  # 127 = highest velocity
    time.sleep(0.1)
    midi.send(NoteOff(note, 0))  # 0 = lowest velocity

Sending MIDI with bytearray

Since we're often battling timing issues in CircuitPython and humans can detect musical timing differences very easily, we can gain back some overhead by using usb_midi directly.

This code is equivalent to the above, without adafruit_midi

import usb_midi
midi_out = usb_midi.ports[1]
midi_out_channel = 3
note_on_status = (0x90 | (midi_out_channel-1))
note_off_status = (0x80 | (midi_out_channel-1))

def play_note(note,velocity=127):
    midi_out.write( bytearray([note_on_status, note, velocity]) )
    time.sleep(0.1)
    midi_out.write( bytearray([note_off_status, note, 0]) )

MIDI over Serial UART

Not exactly USB, but it is MIDI! Both adafruit_midi and the bytearray technique works for Serial MIDI too. With a simple MIDI out circuit you can control old hardware synths.

import busio
midi_out_channel = 3 # human version of MIDI out channel (1-16)
note_on_status = (0x90 | (midi_out_channel-1))
note_off_status = (0x80 | (midi_out_channel-1))
midi_uart = busio.UART(tx=board.GP16, rx=board.GP17, baudrate=31250)

def play_note(note,velocity=127):
    midi_uart.write( bytearray([note_on_status, note, velocity]) )
    time.sleep(0.1)
    midi_uart.write( bytearray([note_off_status, note, 0]) )

Receving MIDI USB and MIDI Serial UART together

MIDI is MIDI, so you can use either the midi_uart or the usb_midi.ports[] created above with adafruit_midi. Here's an example receiving MIDI from both USB and Serial on a QTPy RP2040. Note for receiving serial MIDI, you need an appropriate optoisolator input circuit, like this one for QTPys or this one for MacroPad RP2040.

import board, busio
import usb_midi        # built-in library
import adafruit_midi   # install with 'circup install adafruit_midi'
from adafruit_midi.note_on import NoteOn
from adafruit_midi.note_off import NoteOff

uart = busio.UART(tx=board.TX, rx=board.RX, baudrate=31250, timeout=0.001)
midi_usb = adafruit_midi.MIDI( midi_in=usb_midi.ports[0],  midi_out=usb_midi.ports[1] )
midi_serial = adafruit_midi.MIDI( midi_in=uart, midi_out=uart )

while True:
    msg = midi_usb.receive()
    if msg is not None:
        if isinstance(msg, NoteOn):
            print("usb noteOn:",msg.note, msg.velocity)
        elif isinstance(msg, NoteOff):
            print("usb noteOff:",msg.note, msg.velocity)
    msg = midi_serial.receive()
    if msg is not None:
        if isinstance(msg, NoteOn):
            print("serial noteOn:",msg.note, msg.velocity)
        elif isinstance(msg, NoteOff):
            print("serial noteOff:",msg.note, msg.velocity)

Enable USB MIDI in boot.py (for ESP32S2 and STM32F4)

Some CircuitPython devices like ESP32-S2 based ones, do not have enough USB endpoints to enable all USB functions, so USB MIDI is disabled by default. To enable it, the easiest is to disable USB HID (keyboard/mouse) support. This must be done in boot.py and the the board power cycled.

# boot.py
import usb_hid
import usb_midi
usb_hid.disable()
usb_midi.enable()
print("enabled USB MIDI, disabled USB HID")

WiFi / Networking

Scan for WiFi Networks, sorted by signal strength

Note: this is for boards with native WiFi (ESP32)

import wifi
networks = []
for network in wifi.radio.start_scanning_networks():
    networks.append(network)
wifi.radio.stop_scanning_networks()
networks = sorted(networks, key=lambda net: net.rssi, reverse=True)
for network in networks:
    print("ssid:",network.ssid, "rssi:",network.rssi)

Join WiFi network with highest signal strength

import wifi

def join_best_network(good_networks, print_info=False):
    """join best network based on signal strength of scanned nets"""
    networks = []
    for network in wifi.radio.start_scanning_networks():
        networks.append(network)
    wifi.radio.stop_scanning_networks()
    networks = sorted(networks, key=lambda net: net.rssi, reverse=True)
    for network in networks:
        if print_info: print("network:",network.ssid)
        if network.ssid in good_networks:
            if print_info: print("connecting to WiFi:", network.ssid)
            try:
                wifi.radio.connect(network.ssid, good_networks[network.ssid])
                return True
            except ConnectionError as e:
                if print_info: print("connect error:",e)
    return False
            
good_networks = {"todbot1":"FiOnTheFly",  # ssid, password
                 "todbot2":"WhyFlyWiFi",}
connected = join_best_network(good_networks, print_info=True)
if connected:
    print("connected!")

Ping an IP address

Note: this is for boards with native WiFi (ESP32)

import os
import time
import wifi
import ipaddress

ip_to_ping = "1.1.1.1"

wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))

print("my IP addr:", wifi.radio.ipv4_address)
print("pinging ",ip_to_ping)
ip1 = ipaddress.ip_address(ip_to_ping)
while True:
    print("ping:", wifi.radio.ping(ip1))
    time.sleep(1)

Get IP address of remote host

import os, wifi, socketpool

wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
print("my IP addr:", wifi.radio.ipv4_address)

hostname = "todbot.com"

pool = socketpool.SocketPool(wifi.radio)
addrinfo = pool.getaddrinfo(host=hostname, port=443) # port is required
print("addrinfo", addrinfo)

ipaddr = addrinfo[0][4][0]

print(f"'{hostname}' ip address is '{ipaddr}'")

Fetch a JSON file

Note: this is for boards with native WiFi (ESP32)

import os
import time
import wifi
import socketpool
import ssl
import adafruit_requests

wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
print("my IP addr:", wifi.radio.ipv4_address)
pool = socketpool.SocketPool(wifi.radio)
session = adafruit_requests.Session(pool, ssl.create_default_context())
while True:
    response = session.get("https://todbot.com/tst/randcolor.php")
    data = response.json()
    print("data:",data)
    time.sleep(5)

Serve a webpage via HTTP

Note: this is for boards with native WiFi (ESP32)

The adafruit_httpserver library makes this pretty easy, and has good examples. You can tell it to either server.serve_forver() and do all your computation in your @server.route() functions, or use server.poll() inside a while-loop. There is also the Ampule library.

import time, os, wifi, socketpool
from adafruit_httpserver.server import HTTPServer
from adafruit_httpserver.response import HTTPResponse

my_port = 1234  # set this to your liking
wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
server = HTTPServer(socketpool.SocketPool(wifi.radio))

@server.route("/")  # magic that attaches this function to "server" object
def base(request):
    my_str = f"<html><body><h1> Hello! Current time.monotonic is {time.monotonic()}</h1></body></html>"
    return HTTPResponse(body=my_str, content_type="text/html")
    # or for static content: return HTTPResponse(filename="/index.html")

print(f"Listening on http://{wifi.radio.ipv4_address}:{my_port}")
server.serve_forever(str(wifi.radio.ipv4_address), port=my_port) # never returns

Set RTC time from NTP

Note: this is for boards with native WiFi (ESP32)

Note: You need to set my_tz_offset to match your region

# copied from:
# https://docs.circuitpython.org/projects/ntp/en/latest/examples.html
import time, os, rtc
import socketpool, wifi
import adafruit_ntp

my_tz_offset = -7  # PDT

wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
print("Connected, getting NTP time")
pool = socketpool.SocketPool(wifi.radio)
ntp = adafruit_ntp.NTP(pool, tz_offset=my_tz_offset)

rtc.RTC().datetime = ntp.datetime

while True:
    print("current datetime:", time.localtime())
    time.sleep(5)

Set RTC time from time service

Note: this is for boards with native WiFi (ESP32)

This uses the awesome and free WorldTimeAPI.org site, and this example will fetch the current local time (including timezone and UTC offset) based on the geolocated IP address of your device.

import time, os, rtc
import wifi, ssl, socketpool
import adafruit_requests

wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
print("Connected, getting WorldTimeAPI time")
pool = socketpool.SocketPool(wifi.radio)
request = adafruit_requests.Session(pool, ssl.create_default_context())

print("Getting current time:")
response = request.get("http://worldtimeapi.org/api/ip")
time_data = response.json()
tz_hour_offset = int(time_data['utc_offset'][0:3])
tz_min_offset = int(time_data['utc_offset'][4:6])
if (tz_hour_offset < 0):
    tz_min_offset *= -1
unixtime = int(time_data['unixtime'] + (tz_hour_offset * 60 * 60)) + (tz_min_offset * 60)

print(time_data)
print("URL time: ", response.headers['date'])

rtc.RTC().datetime = time.localtime( unixtime ) # create time struct and set RTC with it

while True:
  print("current datetime: ", time.localtime()) # time.* now reflects current local time
  time.sleep(5)

Also see this more concise version from @deilers78.

What the heck is settings.toml?

It's a config file that lives next to your code.py and is used to store WiFi credentials and other global settings. It is also used (invisibly) by many Adafruit libraries that do WiFi. You can use it (as in the examples above) without those libraries. The settings names used by CircuitPython are documented in CircuitPython Web Workflow.

You use it like this for basic WiFi connectivity:

# settings.toml
CIRCUITPY_WIFI_SSID = "PrettyFlyForAWiFi"
CIRCUITPY_WIFI_PASSWORD = "mysecretpassword"

# code.py
import os, wifi
print("connecting...")
wifi.radio.connect(ssid=os.getenv('CIRCUITPY_WIFI_SSID'),
                   password=os.getenv('CIRCUITPY_WIFI_PASSWORD'))
print("my IP addr:", wifi.radio.ipv4_address)

What the heck is secrets.py?

It's an older version of the settings.toml idea. You may see older code that uses it.

Displays (LCD / OLED / E-Ink) and displayio

displayio is the native system-level driver for displays in CircuitPython. Several CircuitPython boards (FunHouse, MagTag, PyGamer, CLUE) have displayio-based displays and a built-in board.DISPLAY object that is preconfigured for that display. Or, you can add your own I2C or SPI display.

Get default display and change display rotation

Boards like FunHouse, MagTag, PyGamer, CLUE have built-in displays. display.rotation works with all displays, not just built-in ones.

import board
display = board.DISPLAY
print(display.rotation) # print current rotation
display.rotation = 0    # valid values 0,90,180,270

Display an image

Using displayio.OnDiskBitmap

CircuitPython has a built-in BMP parser called displayio.OnDiskBitmap: The images should be in non-compressed, paletized BMP3 format. (how to make BMP3 images)

import board, displayio
display = board.DISPLAY

maingroup = displayio.Group() # everything goes in maingroup
display.root_group = maingroup # show our maingroup (clears the screen)

bitmap = displayio.OnDiskBitmap(open("my_image.bmp", "rb"))
image = displayio.TileGrid(bitmap, pixel_shader=bitmap.pixel_shader)
maingroup.append(image) # shows the image

Using adafruit_imageload

You can also use the adafruit_imageload library that supports slightly more kinds of BMP files, (but should still be paletized BMP3 format as well as paletized PNG and GIF files. Which file format to choose?

  • BMP images are larger but faster to load
  • PNG images are about 2x smaller than BMP and almost as fast to load
  • GIF images are a little bigger than PNG but much slower to load
import board, displayio
import adafruit_imageload
display = board.DISPLAY
maingroup = displayio.Group() # everything goes in maingroup
display.root_group = maingroup # set the root group to display
bitmap, palette = adafruit_imageload.load("my_image.png")
image = displayio.TileGrid(img, pixel_shader=palette))
maingroup.append(image) # shows the image

How displayio is structured

CircuitPython's displayio library works like:

  • an image Bitmap (and its Palette) goes inside a TileGrid
  • a TileGrid goes inside a Group
  • a Group is shown on a Display.

Display background bitmap

Useful for display a solid background color that can be quickly changed.

import time, board, displayio
display = board.DISPLAY         # get default display (FunHouse,Pygamer,etc)
maingroup = displayio.Group()   # Create a main group to hold everything
display.root_group = maingroup  # put it on the display

# make bitmap that spans entire display, with 3 colors
background = displayio.Bitmap(display.width, display.height, 3)

# make a 3 color palette to match
mypal = displayio.Palette(3)
mypal[0] = 0x000000 # set colors (black)
mypal[1] = 0x999900 # dark yellow
mypal[2] = 0x009999 # dark cyan

# Put background into main group, using palette to map palette ids to colors
maingroup.append(displayio.TileGrid(background, pixel_shader=mypal))

time.sleep(2)
background.fill(2)  # change background to dark cyan (mypal[2])
time.sleep(2)
background.fill(1)  # change background to dark yellow (mypal[1])

Another way is to use vectorio:

import board, displayio, vectorio

display = board.DISPLAY  # built-in display
maingroup = displayio.Group()   # a main group that holds everything
display.root_group = maingroup  # put maingroup on the display

mypal = displayio.Palette(1)
mypal[0] = 0x999900
background = vectorio.Rectangle(pixel_shader=mypal, width=display.width, height=display.height, x=0, y=0)
maingroup.append(background)

Or can also use adafruit_display_shapes:

import board, displayio
from adafruit_display_shapes.rect import Rect

display = board.DISPLAY
maingroup = displayio.Group()   # a main group that holds everything
display.root_group = maingroup  # add it to display

background = Rect(0,0, display.width, display.height, fill=0x000000 ) # background color
maingroup.append(background)

Image slideshow

import time, board, displayio
import adafruit_imageload

display = board.DISPLAY      # get display object (built-in on some boards)
screen = displayio.Group()   # main group that holds all on-screen content
display.root_group = screen  # add it to display

file_names = [ '/images/cat1.bmp', '/images/cat2.bmp' ]  # list of filenames

screen.append(displayio.Group())  # placeholder, will be replaced w/ screen[0] below
while True:
    for fname in file_names:
        image, palette = adafruit_imageload.load(fname)
        screen[0] = displayio.TileGrid(image, pixel_shader=palette)
        time.sleep(1)

Note: Images must be in palettized BMP3 format. For more details, see Preparing images for CircuitPython

Dealing with E-Ink "Refresh Too Soon" error

E-Ink displays are damaged if refreshed too frequently. CircuitPython enforces this, but also provides display.time_to_refresh, the number of seconds you need to wait before the display can be refreshed. One solution is to sleep a little longer than that and you'll never get the error. Another would be to wait for time_to_refresh to go to zero, as show below.

import time, board, displayio, terminalio
from adafruit_display_text import label
mylabel = label.Label(terminalio.FONT, text="demo", x=20,y=20,
                      background_color=0x000000, color=0xffffff )
display = board.DISPLAY  # e.g. for MagTag
display.root_group = mylabel
while True:
    if display.time_to_refresh == 0:
        display.refresh()
    mylabel.text = str(time.monotonic())
    time.sleep(0.1)

I2C

Scan I2C bus for devices

from: CircuitPython I2C Guide: Find Your Sensor

import board
i2c = board.I2C() # or busio.I2C(pin_scl,pin_sda)
while not i2c.try_lock():  pass
print("I2C addresses found:", [hex(device_address)
    for device_address in i2c.scan()])
i2c.unlock()

One liner to copy-n-paste into REPL for quicky I2C scan:

import board; i2c=board.I2C(); i2c.try_lock(); [hex(a) for a in i2c.scan()]; i2c.unlock()

Speed up I2C bus

CircuitPython defaults to 100 kHz I2C bus speed. This will work for all devices, but some devices can go faster. Common faster speeds are 200 kHz and 400 kHz.

import board
import busio
# instead of doing
# i2c = board.I2C()
i2c = busio.I2C( board.SCL, board.SDA, frequency=200_000)
# then do something with 'i2c' object as before, like:
oled = adafruit_ssd1306.SSD1306_I2C(width=128, height=32, i2c=i2c)

Timing

Measure how long something takes

Generally use time.monotonic() to get the current "uptime" of a board in fractional seconds. So to measure the duration it takes CircuitPython to do something like:

import time
start_time = time.monotonic()
# put thing you want to measure here, like:
import neopixel
stop_time = time.monotonic()
print("elapsed time = ", stop_time - start_time)

Note that on the "small" versions of CircuitPython in the QT Py M0, Trinket M0, etc., the floating point value of seconds will become less accurate as uptime increases.

More accurate timing with ticks_ms(), like Arduino millis()

If you want something more like Arduino's millis() function, the supervisor.ticks_ms() function returns an integer, not a floating point value. It is more useful for sub-second timing tasks and you can still convert it to floating-point seconds for human consumption.

import supervisor
start_msecs = supervisor.ticks_ms()
import neopixel
stop_msecs = supervisor.ticks_ms()
print("elapsed time = ", (stop_msecs - start_msecs)/1000)

Board Info

Display amount of free RAM

from: https://learn.adafruit.com/welcome-to-circuitpython/frequently-asked-questions

import gc
print( gc.mem_free() )

Show microcontroller.pin to board mappings

from https://gist.github.com/anecdata/1c345cb2d137776d76b97a5d5678dc97

import microcontroller
import board

for pin in dir(microcontroller.pin):
    if isinstance(getattr(microcontroller.pin, pin), microcontroller.Pin):
        print("".join(("microcontroller.pin.", pin, "\t")), end=" ")
        for alias in dir(board):
            if getattr(board, alias) is getattr(microcontroller.pin, pin):
                print("".join(("", "board.", alias)), end=" ")
    print()

Determine which board you're on

import os
print(os.uname().machine)
'Adafruit ItsyBitsy M4 Express with samd51g19'

To get the chip family

import os
print(os.uname().sysname)
'ESP32S2'

Support multiple boards with one code.py

import os
board_type = os.uname().machine
if 'QT Py M0' in board_type:
  tft_clk  = board.SCK
  tft_mosi = board.MOSI
  spi = busio.SPI(clock=tft_clk, MOSI=tft_mosi)
elif 'ItsyBitsy M4' in board_type:
  tft_clk  = board.SCK
  tft_mosi = board.MOSI
  spi = busio.SPI(clock=tft_clk, MOSI=tft_mosi)
elif 'Pico' in board_type:
  tft_clk = board.GP10 # must be a SPI CLK
  tft_mosi= board.GP11 # must be a SPI TX
  spi = busio.SPI(clock=tft_clk, MOSI=tft_mosi)
else:
  print("unsupported board", board_type)

Computery Tasks

Formatting strings

name = "John"
fav_color = 0x003366
body_temp = 98.65
fav_number = 123
print("name:%s color:%06x temp:%2.1f num:%d" % (name,fav_color,body_temp,fav_number))
# 'name:John color:ff3366 temp:98.6 num:123'

Formatting strings with f-strings

(doesn't work on 'small' CircuitPythons like QTPy M0)

name = "John"
fav_color = 0xff3366
body_temp = 98.65
fav_number = 123
print(f"name:{name} color:{fav_color:06x} temp:{body_temp:2.1f} num:{fav_number}")
# 'name:John color:ff3366 temp:98.6 num:123'

Using regular expressions to "findall" strings

Regular expressions are a really powerful way to match information in and parse data from strings. While CircuitPython has a version of the re regex module you may know from desktop Python, it is very limited. Specifcally it doesn't have the very useful re.findall() function. Below is a semi-replacement for findall().

import re
def find_all(regex, some_str):
    matches = []
    while m := regex.search(some_str):
        matches.append( m.groups() )
        some_str = some_str[ m.end(): ] # get past match
    return matches

my_str = "<thing>thing1 I want</thing> <thing>thing2 I want</thing>  <thing>thing3 I want</thing>"
regex1 = re.compile('<thing.*?>(.*?)<\/thing>')
my_matches = find_all( regex1, my_str )
print("matches:", my_matches)

Make and use a config file

# my_config.py
config = {
    "username": "Grogu Djarin",
    "password": "ig88rules",
    "secret_key": "3a3d9bfaf05835df69713c470427fe35"
}

# code.py
from my_config import config
print("secret:", config['secret_key'])
# 'secret: 3a3d9bfaf05835df69713c470427fe35'

Run different code.py on startup

Use microcontroller.nvm to store persistent state across resets or between boot.py and code.py, and declare that the first byte of nvm will be the startup_mode. Now if you create multiple code.py files (say) code1.py, code2.py, etc. you can switch between them based on startup_mode.

import time
import microcontroller
startup_mode = microcontroller.nvm[0]
if startup_mode == 1:
    import code1      # runs code in `code1.py`
if startup_mode == 2:
    import code2      # runs code in `code2.py`
# otherwise runs 'code.py`
while True:
    print("main code.py")
    time.sleep(1)

Note: in CircuitPyton 7+ you can use supervisor.set_next_code_file() to change which .py file is run on startup. This changes only what happens on reload, not hardware reset or powerup. Using it would look like:

import supervisor
supervisor.set_next_code_file('code_awesome.py')
# and then if you want to run it now, trigger a reload
supervisor.reload()

Coding Techniques

Map an input range to an output range

# simple range mapper, like Arduino map()
def map_range(s, a1, a2, b1, b2):
    return  b1 + ((s - a1) * (b2 - b1) / (a2 - a1))

# example: map 0-0123 value to 0.0-1.0 value
val = 768
outval = map_range( val, 0,1023, 0.0,1.0 )
# outval = 0.75

Constrain an input to a min/max

The Python built-in min() and max() functions can be used together to make something like Arduino's constrain() to clamp an input between two values.

# constrain a value to be 0-255
outval = min(max(val, 0), 255)
# constrain a value to be 0-255 integer
outval = int(min(max(val, 0), 255))
# constrain a value to be -1 to +1
outval = min(max(val, -1), 1)

Turn a momentary value into a toggle

import touchio
import board

touch_pin = touchio.TouchIn(board.GP6)
last_touch_val = False  # holds last measurement
toggle_value = False  # holds state of toggle switch

while True:
  touch_val = touch_pin.value
  if touch_val != last_touch_val:
    if touch_val:
      toggle_value = not toggle_value   # flip toggle
      print("toggle!", toggle_value)
  last_touch_val = touch_val

Do something every N seconds without sleep()

Also known as "blink-without-delay"

import time
last_time1 = time.monotonic()  # holds when we did something #1
last_time2 = time.monotonic()  # holds when we did something #2
while True:
  if time.monotonic() - last_time1 > 2.0:  # every 2 seconds
    last_time1 = time.monotonic() # save when we do the thing
    print("hello!")  # do thing #1
  if time.monotonic() - last_time2 > 5.0:  # every 5 seconds
    last_time2 = time.monotonic() # save when we do the thing
    print("world!")  # do thing #2

System error handling

Preventing Ctrl-C from stopping the program

Put a try/except KeyboardInterrupt to catch the Ctrl-C on the inside of your main loop.

while True:
  try:
    print("Doing something important...")
    time.sleep(0.1)
  except KeyboardInterrupt:
    print("Nice try, human! Not quitting.")

Also useful for graceful shutdown (turning off neopixels, say) on Ctrl-C.

import time, random
import board, neopixel, rainbowio
leds = neopixel.NeoPixel(board.NEOPIXEL, 1, brightness=0.4 )
while True:
  try:
    rgb = rainbowio.colorwheel(int(time.monotonic()*75) % 255)
    leds.fill(rgb)
    time.sleep(0.05)
  except KeyboardInterrupt:
    print("shutting down nicely...")
    leds.fill(0)
    break  # gets us out of the while True

Prevent auto-reload when CIRCUITPY is touched

Normally, CircuitPython restarts anytime the CIRCUITPY drive is written to. This is great normally, but is frustrating if you want your code to keep running, and you want to control exactly when a restart happens.

import supervisor
supervisor.runtime.autoreload = False  # CirPy 8 and above
#supervisor.disable_autoreload()  # CirPy 7 and below

To trigger a reload, do a Ctrl-C + Ctrl-D in the REPL or reset your board.

Raspberry Pi Pico boot.py Protection

Also works on other RP2040-based boards like QTPy RP2040. From https://gist.github.com/Neradoc/8056725be1c209475fd09ffc37c9fad4

# Copy this as 'boot.py' in your Pico's CIRCUITPY drive
# Useful in case Pico locks up (which it's done a few times on me)
import board
import time
from digitalio import DigitalInOut,Pull

led = DigitalInOut(board.LED)
led.switch_to_output()

safe = DigitalInOut(board.GP14)  # <-- choose your button pin
safe.switch_to_input(Pull.UP)

def reset_on_pin():
    if safe.value is False:
        import microcontroller
        microcontroller.on_next_reset(microcontroller.RunMode.SAFE_MODE)
        microcontroller.reset()

led.value = False
for x in range(16):
	reset_on_pin()
	led.value = not led.value  # toggle LED on/off as notice
	time.sleep(0.1)

Hacks

Using the REPL

Display built-in modules / libraries

Adafruit CircuitPython 6.2.0-beta.2 on 2021-02-11; Adafruit Trinket M0 with samd21e18
>>> help("modules")
__main__          digitalio         pulseio           supervisor
analogio          gc                pwmio             sys
array             math              random            time
board             microcontroller   rotaryio          touchio
builtins          micropython       rtc               usb_hid
busio             neopixel_write    storage           usb_midi
collections       os                struct
Plus any modules on the filesystem

Use REPL fast with copy-paste multi-one-liners

(yes, semicolons are legal in Python)

# load common libraries (for later REPL experiments)
import time, board, analogio, touchio; from digitalio import DigitalInOut,Pull

# create a pin and set a pin LOW (if you've done the above)
pin = DigitalInOut(board.GP0); pin.switch_to_output(value=False)

# print out board pins and objects (like `I2C`, `STEMMA_I2C`, `DISPLAY`, if present)
import board; dir(board)

# print out microcontroller pins (chip pins, not the same as board pins)
import microcontroller; dir(microcontroller.pin)

# release configured / built-in display
import displayio; displayio.release_displays()

# turn off auto-reload when CIRCUITPY drive is touched
import supervisor; supervisor.runtime.autoreload = False

# test neopixel strip, make them all purple
import board, neopixel; leds = neopixel.NeoPixel(board.GP3, 8, brightness=0.2); leds.fill(0xff00ff)
leds.deinit()  # releases pin

# scan I2C bus
import board; i2c=board.I2C(); i2c.try_lock(); [hex(a) for a in i2c.scan()]; i2c.unlock()

Turn off built-in display to speed up REPL printing

By default CircuitPython will echo the REPL to the display of those boards with built-in displays. This can slow down the REPL. So one way to speed the REPL up is to hide the displayio.Group that contains all the REPL output. (From user @argonblue in the CircuitPython Discord chat)

import board
display = board.DISPLAY
display.root_group.hidden = True
# and to turn it back on
display.root_group.hidden = False

You can also turn back on the REPL after using the display for your own graphics with:

display.root_group = None

Python tricks

These are general Python tips that may be useful in CircuitPython.

Create list with elements all the same value

blank_array = [0] * 50   # creats 50-element list of zeros

Convert RGB tuples to int and back again

Thanks to @Neradoc for this tip:

rgb_tuple = (255, 0, 128)
rgb_int = int.from_bytes(rgb_tuple, byteorder='big')

rgb_int = 0xFF0080
rgb_tuple2 = tuple((rgb_int).to_bytes(3,"big"))

rgb_tuple2 == rgb_tuple

Storing multiple values per list entry

Create simple data structures as config to control your program. Unlike Arduino, you can store multiple values per list/array entry.

mycolors = (
    # color val, name
    (0x0000FF, "blue"),
    (0x00FFFF, "cyan"),
    (0xFF00FF, "purple"),
)
for i in range(len(mycolors)):
    (val, name) = mycolors[i]
    print("my color ", name, "has the value", val)

Python info

How to get information about Python inside of CircuitPython.

Display which (not built-in) libraries have been imported

import sys
print(sys.modules.keys())
# 'dict_keys([])'
import board
import neopixel
import adafruit_dotstar
print(sys.modules.keys())
prints "dict_keys(['neopixel', 'adafruit_dotstar'])"

List names of all global variables

a = 123
b = 'hello there'
my_globals = sorted(dir)
print(my_globals)
# prints "['__name__', 'a', 'b']"
if 'a' in my_globals:
  print("you have a variable named 'a'!")
if 'c' in my_globals:
  print("you have a variable named 'c'!")

Display the running CircuitPython release

With an established serial connection, press Ctrl+c:

Adafruit CircuitPython 7.1.1 on 2022-01-14; S2Pico with ESP32S2-S2FN4R2
>>>

Without connection or code running, check the boot_out.txt file in your CIRCUITPY drive.

import os
print(os.uname().release)
'7.1.1'
print(os.uname().version)
'7.1.1 on 2022-01-14'

Host-side tasks

Things you might need to do on your computer when using CircuitPython.

Installing CircuitPython libraries

The below examples are for MacOS / Linux. Similar commands are used for Windows

Installing libraries with circup

circup can be used to easily install and update modules

$ pip3 install --user circup
$ circup install adafruit_midi
$ circup update   # updates all modules

Freshly update all modules to latest version (e.g. when going from CP 6 -> CP 7) (This is needed because circup update doesn't actually seem to work reliably)

circup freeze > mymodules.txt
rm -rf /Volumes/CIRCUITPY/lib/*
circup install -r mymodules.txt

And updating circup when a new version of CircuitPython comes out:

$ pip3 install --upgrade circup

Copying libraries by hand with cp

To install libraries by hand from the CircuitPython Library Bundle or from the CircuitPython Community Bundle (which circup doesn't support), get the bundle, unzip it and then use cp -rX.

cp -rX bundle_folder/lib/adafruit_midi /Volumes/CIRCUITPY/lib

Note: on limited-memory boards like Trinkey, Trinket, QTPy, you must use the -X option on MacOS to save space. You may also need to omit unused parts of some libraries (e.g. adafruit_midi/system_exclusive is not needed if just sending MIDI notes)

Preparing images for CircuitPython

There's two ways to load images for use with displayio:

displayio.OnDisBitmap():

  • can load "indexed" (aka "palette") non-compressed BMP3 images
  • doesn't load image into RAM (great for TileGrids)

adafruit_imageload

  • can load BMP3 images with RLE compression
  • loads entire image into RAM (thus you may run out of memory)
  • an load palette PNG images and GIF images
  • PNG image loading is almost as fast as BMP and uses 1/2 the disk space
  • GIF loading is very slow

To make images load faster generally, you can reduce the number of colors in the image. The maximum number of colors is 256, but try reducing colors to 64 or even 2 if it's a black-n-white image.

Some existing Learn Guides:

And here's some ways to do the conversions.

Online

Most online image converters do not create BMPs in the proper format: BMP3, non-compressed, up to 256 colors in an 8-bit palette.

However @Neradoc found the site convert2bmp will work when you set "Color:" mode to "8 (Indexed)". Some initial tests show this works! I'd recommend also trying out one of the following techniques too to have finer control.

The site https://cancerberosgx.github.io/magic/playground/ lets you use any of the ImageMagick commands below to convert images. It's really handy if you can't install ImageMagick locally.

Command-line: using ImageMagick

ImageMagick is a command-line image manipulation tool. With it, you can convert any image format to BMP3 format. The main ImageMagick CLI command is convert.

convert myimage.jpg -resize 240x240 -type palette -colors 64 -compress None BMP3:myimage_for_cirpy.bmp

You can also use this technique to create reduced-color palette PNGs:

convert myimage.jpg -resize 240x240 -type palette -colors 64 myimage.png

Command-line: using GraphicsMagick

GraphicsMagick is a slimmer, lower-requirement clone of ImageMagick. All GraphicsMagick commands are accessed via the gm CLI command.

gm convert myimage.jpg -resize 240x240 -colors 64 -type palette -compress None BMP3:myimage_for_cirpy.bmp

Making images smaller or for E-Ink displays

To make images smaller (and load faster), reduce number of colors from 256. If your image is a monochrome (or for use with E-Ink displays like MagTag), use 2 colors. The "-dither" options are really helpful for monochrome:

convert cat.jpg -dither FloydSteinberg -colors 2 -type palette BMP3:cat.bmp

NodeJs: using gm

There is a nice wrapper around GraphicsMagick / Imagemagick with the gm library. A small NodeJs program to convert images could look like this:

var gm = require('gm');
gm('myimage.jpg')
    .resize(240, 240)
    .colors(64)
    .type("palette")
    .compress("None")
    .write('BMP3:myimage_for_cirpy.bmp', function (err) {
        if (!err) console.log('done1');
    });

Python: using PIL / pillow

The Python Image Library (PIL) fork pillow seems to work the best. It's unclear how to toggle compression.

from PIL import Image
size = (240, 240)
num_colors = 64
img = Image.open('myimage.jpg')
img = img.resize(size)
newimg = img.convert(mode='P', colors=num_colors)
newimg.save('myimage_for_cirpy.bmp')

Preparing audio files for CircuitPython

CircuitPython can play WAV files great, but it prefers the WAV files to be in a specific format. I've found the best trade-off in quality / flash-space / compatibility to be:

  • PCM 16-bit signed PCM
  • Mono (but stereo will work if using I2S or SAMD51)
  • 22050 Hz sample rate

And remember that these settings must match how you're setting up the audiomixer object. So for the above settings, you'd create an audiomixer.Mixer like:

mixer = audiomixer.Mixer(voice_count=1, sample_rate=22050, channel_count=1,
                         bits_per_sample=16, samples_signed=True)

To convert WAVs for CircuitPython, I like to use Audacity or the sox command-line tool. Sox can convert just about any audio to the correct WAV format:

sox loop.mp3 -b 16 -c 1 -r 22050 loop.wav

To get sox on various platforms:

Some audio Learn Guide links:

Circup hacks

circup is a great tool to help you install CircuitPython libraries. Think of it like pip or npm for CircuitPython.

Finding where circup stores its files

Instead of downloading the bundles by hand, circup has it already downloaded an unzipped. Here's how to find that directory:

circup_dir=`python3 -c 'import appdirs; print(appdirs.user_data_dir(appname="circup", appauthor="adafruit"))'`
ls $circup_dir

About this guide

  • Many of the code snippets are not considered "well-formatted" by Python linters. This guide favors brevity over strict style adherence.

  • The precursor to this guide is QTPy Tricks, which has similar but different (and still valid) fun things to do in CircuitPython.

  • This guide is the result of trying to learn Python via CircuitPython and from very enlightening discussions with John Edgar Park. I have a good background in other languages, but mostly C/C++, and have taught classes in Arduino for several years. This informs how I've been thinking about things in this guide.

About

Some CircuitPython tricks, mostly reminders to myself

License:MIT License


Languages

Language:Python 99.4%Language:Shell 0.6%