NVMe-of/TCP Boot with openSUSE Virtual Machines

DISCLAIMER

These instructions have been created with diligence and are provided in the hope that they will be useful, but without guarantee of any kind. Use at you own risk.

Note for Developers

The instructions below are based on various high level tools such as vagrant and ansible, and driven by shell scripts and Makefiles. This is designed to be flexible and relatively easy to set up, but it naturally hides a lot of the details that go on behind the scenes.

If you want to understand the setup in more detail, please check the Basic walkthrough for developers.

Full Proof-of-Concept

Quick Start for the Impatient

Check the Prerequisites.
Run make help-rootless and apply the suggested settings.
Run make server-up.
Run make AUTOINST=1 inst, hit ESC quickly after VM startup.
Open Boot Manager and start EFI Internal Shell, let startup.nsh run. The boot menu will be displayed.
Open the boot manager again and watch out for an "NVMe" entry. If it doesn't exist, something went wrong, see below.
Reset the VM from the EFI Menu, it will reboot.
Select the DVD as boot device. The Installation menu will be displayed.
Edit the Installation entry, and add console=ttyS0 to the kernel command line.
Start the installation.
After installation, the installed VM will boot from NVMe-oF. The root password is "timberland".

Features

Operated by simple make commands
Automated network setup with bridge and optionally with OpenVSwitch and VLAN
NVMe target is running as a vagrant VM
Automated server setup matching the network setup
Multiple VMs with different configurations can be set up in parallel
Proper ACL settings on the NVMe server
IPv4 and IPv6
DHCP server, DNS server
NVMe discovery
Support for creating libvirt domains
Support for changing configurations easily and consistently to avoid failure due to common configuration mistakes.

Prerequisites

Packages

libvirt, qemu-kvm, make, git, wget, curl, jq, mkisofs, dnsmasq, sudo
vagrant, vagrant-libvirt, ansible, python-jmespath, python-netaddr
optional: openvswitch
optional (for running test VM under libvirt): xsltproc, mtools
For newer versions of ansible, the collections ansible.posix and/or community.general may be required (install with ansible-galaxy).

Daemons

The libvirt and (if used) the OpenVSwitch daemon must be running.

Enabling Rootless Operation

(If you intend to run everything as root, skip this section).

While most of this Proof of Concept can be run rootless, some commands require superuser priviliges, in particular network setup. Your user ID should have permissions to run virtual machines both under plain qemu¹ and under libvirt. On most modern Linux distributions, this is granted by adding the user to the groups qemu (or kvm) and libvirt, respectively.

Thr command make help-rootless prints configuration hints to enable passwordless execution for those commands that need root permissions. The output looks like this, with some variables substituted to match your environment:

###  User joe must be able control qemu and libvirt
Usually that means joe should be member of the groups "qemu" and "libvirt"

### Recommended sudoers configuration (add with visudo):
User_Alias NVME_USERS = joe
Host_Alias NVME_HOSTS = workstation
Cmd_Alias NVME_CMDS = /home/joe/nvme-poc/qemu.sh ""
Cmd_Alias NVME_NET = /home/joe/nvme-poc/network/setup.sh "", /home/joe/nvme-poc/network/cleanup.sh ""
Defaults!NVME_CMDS env_keep += "VM_NAME VM_UUID VM_OVMF_IMG VM_BRIDGE VM_ISO VM_DUD VM_VGA_FLAGS V"
Defaults!NVME_NET env_keep += "NVME_USE_OVS V"
NVME_USERS NVME_HOSTS=(root) NOPASSWD: NVME_CMDS
NVME_USERS NVME_HOSTS=(root) NOPASSWD: NVME_NET
### End of sudoers config ###

### /etc/qemu/bridge.conf configuration
allow br_nvme

Review these suggestions, and apply them as you see fit.

Setting up the Environment

The PoC is driven by the make command. Run make help for a quick overview. At the first make invocation, two configuration files env-config.mk and vm-config.mk will be created. By default, the test environment will create a bridge br_nvme with two subnets with the IP ranges 192.168.49.0/24 and fddf:d:f:49::/64. If this overlaps with existing networks in your environment, change SUBNET_BASE in env-config.mk².

The default setup will create two NVME subsystems and export them to one client VM each.

Save your configuration, and run

make server-up

This will set up the network, start the vagrant server VM, and configure it to serve a namespace (disk) for your first client VM. The server has the IP addresses 192.168.49.10 and fddf:d:f:49::10³. At the end of the procedure, the configured target ports and subsystems will be printed to the screen.

To test the server, run (as root)

nvme discover -t tcp -a 192.168.49.10  -s 4420 -q "nqn.2014-08.org.nvmexpress:uuid:$UUID"

where UUID has been printed by the previous command, or can be found in the file uuid-$(VM_NAME).mk⁴, where VM_NAME is set in vm-config.mk and defaults to leap.

Installing a Client Virtual Machine

Important: kill a hanging qemu VM with Ctrl-b x.⁵

The settings for the client are in vm-config.mk. Leaving the defaults as-is should work for your first installation. You can change the settings later.

The PoC uses openSUSE Leap or SUSE Linux Enterprise (SLE) (BASE_DIST in vm-config.mk). Versions 15.4 and 15.5 are supported (VERSION in vm-config.mk). If you have an installation medium (DVD) for the configured openSUSE distribution around, copy or link it to install.iso in the top directory. Otherwise, the next command will download the image from the internet⁶.

The following command will download and build all necessary artifacts and start the VM. Most importantly, it will build a small EFI disk with the NvmeOfCli.efi executable and a startup.nsh script. This disk must be booted to set the NVMe-oF boot attempt variables. Run

make inst

First-time boot

As soon as the VM starts, hit the ESC key. If you miss it and PXE boot starts, kill the VM with Ctrl-b x and try again. In the EFI main menu, select Boot Maintenance Manager → Boot Options and disable the PXE boot options. Back in the main EFI menu, select Boot Manager → EFI Internal Shell. Don't interrupt and let the shell execute startup.nsh. Back in the main menu, reset the VM. See What happened here? for an explanation of this step.

Controlling the NVMe-oF setup

(This step can be skipped). Hit ESC again during boot. If you're dropped into the UEFI shell, type exit. In the UEFI main menu, enter the Boot Manager. Verify that an NVMe-oF device is now offered a boot option. If this is not the case, you'll need to troubleshoot your network and NVMe-oF configuration. Select the first DVD-ROM in the boot manager to start the installation.

Installation

Wait until you see the boot menu from the openSUSE DVD (you my have to type t first to display the menu on serial console). Move cursor to Installation, type e to edit the line, and add console=ttyS0 on the line starting with linux⁷. Type Ctrl-x to start the installation.

Follow the installation procedure as usual. Do not enable online repositories, as by default the VM runs in an isolated network without internet connectivity. The NVMeoF disk should be detected as /dev/nvme0n1. Eventually, the system will reboot, and you will be able to log in and examine the result as shown in Examining the booted system.

After shutdown, you can boot the installed system with make qemu.

Modifying the Configuration

Find the most important settings in vm-config.mk. You can modify them in this file, or (for temporary changes) you can set the variables directly on the make command line, like this:

make VM_NAME=host2 SUBSYS=02 CONFIG=Static6 DISCOVERY=1

The individual settings are:

CONFIG: an attempt configuration template from the config subdirectory. Static4 is a static IPv4 configuration, Dhcp6 an IPv6 configuration using DHCP, etc.
DISCOVERY: set to 1 to use NVMe discovery rather than expclicit storage subsystem reference in the NVMe boot attempt.
VM_NAME: If you change this, a new UUID will be generated, and you'll work with a different VM. Make sure to set SUBSYS to a different number if you want to use the old and new VM in parallel.
SUBSYS: A 2-digit number indicating the subsystem on the server which should be exported to this VM. It must be no larger than NVME_MAX_NAMESPACES in env-config.mk.
VERSION: The openSUSE version to install. 15.4 or 15.5 are supported. 15.5 contains native support for NVMe-oF/TCP boot, whereas 15.4 needs a driver update disk (DUD) with updated packages. The PoC scripts will build the DUD automatically.
VLAN_ID: (only in OVS setups with VM_NETWORK_TYPE=ovs): If set to 1 (actually, $(OVS_VLAN_ID)), a tagged VLAN with VLAN ID 1 will be configured on the client VM.
USE_GW: Add a gateway. This makes it possible to configure a target that is outside the directly attached subnet of the VM. Actually doing that requires configuring the target IP address in TARGET explicitly; this is not automated. USE_GW also influences the dnsmasq configuration; it requires a make net-down; make server-up sequence.

After changing the attempt configuration, you will need to:

run make server-config to make sure the server has the correct settings for VM_NAME and SUBSYS.
boot the VM into EFI shell again (hitting ESC quickly after boot), run the (automatically regenerated) startup.nsh script, and reset the system once to actually use the changed settings.

Configuring the DHCP Root-path Option

Default configuration for dnsmasq:

dhcp-range=set:br_nvme_4,192.168.49.129,192.168.49.254,300
dhcp-option=tag:br_nvme_4,option:root-path,"nvme+tcp://vagrant-nvmet.br_nvme:4420/nqn.2014-08.org.nvmexpress.discovery//"

If CONFIG := DhcpRoot4 is used, this root path should be retrieved by the VM. In the given format, it requires DNS resolution and successful NVMe discovery by the client VM.

If you want to play with different DHCP root path settings, you can do so by creating a file network.conf in the top level directory, and setting the shell variable DNSMASQ_EXTRA_OPTS, like this:

DNSMASQ_EXTRA_OPTS="\
dhcp-host=52:54:00:a2:a7:b2,set:host1,192.168.49.97,host1
dhcp-option=tag:host1,option:root-path,\"nvme+tcp://192.168.50.10:4420/nqn.2022-12.org.nvmexpress.boot.poc:zeus.vagrant-nvmet.subsys03//\""

This requires running make net-down; make server-up. For temporary changes you can also kill the current dnsmasq instance, edit the configuration file, and start another dnsmasq for the test network:

kill $(cat /run/dnsmasq/dnsmasq-nvmeof.pid)
vi /run/dnsmasq/dnsmasq-nvmeof.conf  # add changes as described above
dnsmasq --pid-file=/run/dnsmasq/dnsmasq-nvmeof.pid -C /run/dnsmasq/dnsmasq-nvmeof.conf

The general format of the root path is

nvme+tcp://${TARGET}[:${PORT}]/${SUBSYSNQN}/${NID}

The NID (namespace ID) may be empty, in which case the namespace it will be chosen automatically. For an emtpy NID use "/" (like above) or "0". A real NID has the format urn:uuid:cc3f2135-f931-4569-baea-0eee7113a526. TARGET may be given as IPv4 address or host name. The SUBSYSNQN can be the well-known discovery NQN nqn.2014-08.org.nvmexpress.discovery, in which case the NID should be empty, and the host will an attempt a discovery to the given target. Note: the default port for discovery is 8009, port 4420 needs to be specifically set in the root-path to use it.

Configuring IPv6

NVMVe-oF/TCP over IPv6 doesn't work perfectly in EDK2 yet. Be prepared for sporadic hangs or timeouts. This is work in progress.

Unlike IPv4, the network configuration is not taken from the CONFIG file. It must be configured in the EFI UI instead: Device Manager → Network Device List → MAC address → IPv6 Network Configuration → Enter Configuration Menu; then set either Policy: automatic (for DHCP or IPv6 SLAAC), or set Policy: manual and add IPv6 address and gateway under Advanced Configuration.

Alternatively, this can be configured in the EFI shell. The most reliable way to bring up an NVMeoF boot with IPv6 is as follows (assuming the standard bridge with subnet fddf:d:f:49:: is in use):

rm vm/$VM_NAME-vars.fd    # VM_NAME from config.mk
make qemu
# hit ESC, disable PXE boot options 
# boot EFI shell, hit ESC (*do not* run startup.nsh)
# in efi shell, use ifconfig6 like above:
ifconfig6 -s eth0 man host fddf:d:f:49::50/64 gw fddf:d:f:49::1
# or for DHCP/SLAAC: ifconfig6 -s eth0 auto
reset   # or ctrl-b x for poweroff
# hit ESC again when the VM reboots
# boot EFI shell and run startup.nsh this time

Note that running startup.nsh and reading the CONFIG file is still necessary for configuring NVMe-oF target parameters.

Advanced Configuration

Examine the Makefile and the scripts qemu.sh, libvirt.sh, and network/setup.sh for further configuration options, which are all in CAPITAL LETTERS and can usually be set via environment variables. The Makefile uses environment variables (export statements) to control the configuration of the helper scripts, but the scripts have additional variables that enable more fine-grained control.

qemu.sh and network/setup.sh allow customizations in config files qemu.conf (or qemu-$VM_NAME-conf) and network.conf in the to directory, respectively. See Configuring the DHCP Root-path Option above for an example, and for instructions to restart dnsmasq.

Some variables which are derived in the Makefile, such as IPADDR, TARGET, and GATEWAY, can be set in vm-config.mk instead, overriding the derived values.

The server configuration can be modified in the ansible input file nvmet-server/group_vars/nvme_servers (YaML format). This file is in part auto-generated by the Makefile, but customizations are allowed. For example, the all_nvme_subsystems variable can be modified to assign multiple namespaces to one host.

Using a test release of the OVMF firmware

By default, the latest released OVMF firmware from the Timberland EDK2 GitHub repository will be downloaded and used. The Timberland project uses GitHub Actions to build firmware images automatically for new pull requests. These images can be downloaded from the actions page. Click on the workflow run you're interested in, and on the workflow page, click on "artifact". A file called artifact.zip will be downloaded. It contains a file timberland-ovmf.zip. Copy this file into your working directory and run

make OVMF
make vars-clean
make vars

This will create the images for UEFI code and variables under ovmf/OVMF_CODE.fd and ovmf/OVMF_VARS.fd, respectively, and create a copy of the variable store that's usable for your virtual machine.

Using Libvirt

Using make libvirt instead of make inst will create a libvirt VM called nvmeof-$VM_NAME, which can be started, stopped and otherwise manipulated using virt-manager as usual. This requires mtools and xsltproc.

When using libvirt, you should use the virt-manager UI to modify the settings of the test VM (the network bridge, CD-ROM drive, etc.). Run make efidisk.img for changing attempt parameters on the EFI disk.

You can also run make libvirt after make inst. Actually, the libvirt VM and make qemu will use the same non-volatile EFI store and NVMeoF subsystem, so make sure you don't run both at the same time.

Cleaning Up

Note: None of the commands below stop any running client VMs. You need to do this manually.

make vars-clean: removes the non-volatile EFI variable store, which will be regenerated empty the next time the VM is started.
make libvirt-clean: undefines the libvirt VM for VM_NAME.
make server-down: shuts down the nvme server.
make net-down: shuts down the nvme server and the test network.
make server-destroy: removes the vagrant server instance, which will be recreated with the next make server-up. Run make server-destroy if you want to make changes in env-config.mk. Note that this does not clean out the served namespaces (disks) of the server, which are stored in the libvirt storage pool default (usually /var/lib/libvirt/images). They will be re-used by the new server after make server-up.
make all-clean: cleanup everything, except the namespaces (see above).

Troubleshooting

Use make V=1 to show details of the actions carried out by make. Use V=2 to enable verbose output of helper scripts, vagrant, and ansible.

Network settings

Most of the time, failure to boot from NVMe is caused by network setup issues.

Check the status of the bridges and interfaces. If in doubt, restart the virtual networks using
```
  make net-down
  make server-up
```
Check firewall settings on the VM host; at the very least, DHCPv4/v6 queries need to be received by the dnsmasq daemon running on the host.
Check the status of the NVMe target VM. You can enter the VM by changing to the nvmet-server subdirectory and running vagrant ssh. Once in the VM, you can run sudo to investigate the status and apply fixes. Verify that all configured interfaces of the server VM are up and have the expected IP addresses (see Setting up the environment), and that the VM host can be pinged through any of them. By default, all IP addresses of the NVMet server exept the address of eth0 will end with .10 for IPv4 or ::10 for IPv6. Also run nvmetcli ls to verify the volumes exported by the server.

Client settings

Examine the NVMe-oF configuration file efidisk/Config and make sure the settings match the configured bridges and the subsystems exported by the server.

Debugging

On the VM host, the output of dnsmasq can be helpful to see if the server and/or the client successfully retrieve IP addresses. It's recommended to use a DHCP setup for the client initially, because otherwise this debugging method won't be available.

Use tcpdump or similar tools on the VM host and / or on the NVMe target to see whether the client tries to connect. The system log on the NVMe target will log both successful and unsuccessful NVMe connection attempts.

How Does This Work?

The bulk of the logic that enables NVMeoF boot, as far as Linux is concerned, is in nvme-cli. Other tools basically just need to consume the output of nvme-cli show-nbft, create a networking setup according to these settings, and run nvme-cli connect-nbft. This must be done

during installation, before entering the partitioning dialog,
during boot of the installed system

Setup in the installed system

Distributions using dracut

On distributions using dracut for creating the initial RAM filesystem, dracut's nvmf module has been extended for NBFT support. The logic is very similar to the iBFT-parsing logic in the iscsi module.

In the cmdline step (the first step executed by dracut), the NBFT ACPI table is detected and parsed, and the content is translated into ip=... directives that are understood by dracut. Furthermore, rd.neednet=1 is set, and ifname directives are created to make sure the correct interfaces are configured in the initqueue stage.
In the pre-udev step, udev rules are generated to rename network interfaces according to the ifname directives, and bring these interfaces up.
In the udev stage, the previously generated rules are executed.
In the initqueue stage, dracut attempts to run nvme connect-nbft after the udev queue has settled. Because rd.neednet is set, dracut should try to bring up the configured interfaces, and once this is finished, the initqueue hooks will be called and the NVMeoF connetion established.

This approach requires no changes in dracut's network setup modules. Thus it should work with all network backends that dracut supports.

Other distributions

TBD.

Setup during installation

This part depends strongly on the distribution and the capabilities of the installation program.

openSUSE Leap and SUSE Linux Enterprise Server (SLE)

openSUSE Leap 15.5 and SLE 15-SP5 have native support for installing on NVMe-oF/TCP in their installation programs (linuxrc and YaST). Presence of an NBFT table is automatically detected.

On openSUSE Leap 15.4 and SLE15-SP4, the driver update disk (DUD) concept⁸ is leveraged to install updated packages for nvme-cli, dracut and their dependencies. These packages are not official 15.4 packages, but they are compiled from the same sources as the native 15.5 packages. Moroeover, the 15.4 DUD contains a shell script, which is run by the installer before performing the actual installation. The script parses the NBFT, brings up the NBFT interface(s), and connects to the NVMeoF subsystems.

qemu will only be run under your user ID if no OpenVSwitch bridge is used, because bringing up openvswitch interfaces doesn't work with rootless qemu. ↩
If you want to use OpenVSwitch (OVS), set NVME_USE_OVS to 1. In this case, additional IP ranges 192.168.50.0/24, 192.168.51.0/24, fddf:d:f:50::/64, and fddf:d:f:51::/64 will be created. Again, modify env-config.mk if necessary to avoid overlapping IP ranges. ↩
plus equivalent addresses ending in "10" for the OVS subnets, if configured. ↩
Without the -q argument, nvme discover will print no subsystem, because ACLs on the server restrict access. ↩
By default, this PoC uses Ctrl-b x rather than qemu's default Ctrl-a x, in order to be able to run the PoC under screen. ↩
The automatic download works for openSUSE leap only. For SLE, you need to obtain an iso image from the [SUSE download site](https://www.suse.com/download/sles/ and create a symbolic link in the top directory pointing to this image. For SLE15-SP5, the name of the symbolic link should be SLE-15-SP5-Full-x86_64-Media1.iso. ↩
Alternatively, set VM_VGA_FLAGS in vm-config.mk to enable a VGA console and graphical UI for qemu. ↩
See https://github.com/openSUSE/mkdud/blob/master/HOWTO.md ↩

timberland-sig / suse-linux-poc

NVMe-of/TCP Boot with openSUSE Virtual Machines

DISCLAIMER

Note for Developers

Full Proof-of-Concept

Quick Start for the Impatient

Features

Prerequisites

Packages

Daemons

Enabling Rootless Operation

Setting up the Environment

Installing a Client Virtual Machine

First-time boot

Controlling the NVMe-oF setup

Installation

Modifying the Configuration

Configuring the DHCP Root-path Option

Configuring IPv6

Advanced Configuration

Using a test release of the OVMF firmware

Using Libvirt

Cleaning Up

Troubleshooting

Network settings

Client settings

Debugging

How Does This Work?

Setup in the installed system

Distributions using dracut

Other distributions

Setup during installation

openSUSE Leap and SUSE Linux Enterprise Server (SLE)

About

Languages

NVMe-of/TCP Boot with openSUSE Virtual Machines

DISCLAIMER

Note for Developers

Full Proof-of-Concept

Quick Start for the Impatient

Features

Prerequisites

Packages

Daemons

Enabling Rootless Operation

Setting up the Environment

Installing a Client Virtual Machine

First-time boot

Controlling the NVMe-oF setup

Installation

Modifying the Configuration

Configuring the DHCP Root-path Option

Configuring IPv6

Advanced Configuration

Using a test release of the OVMF firmware

Using Libvirt

Cleaning Up

Troubleshooting

Network settings

Client settings

Debugging

How Does This Work?

Setup in the installed system

Distributions using dracut

Other distributions

Setup during installation

openSUSE Leap and SUSE Linux Enterprise Server (SLE)

Footnotes

About

Languages