DPS5005_pyGUI

A python GUI to display & control DPS5005 power supply

Hardware: DPS5005
Software: v1.6

Additional settings within hardware:

hold 'up' arrow while powering on to access interface setup area.
Modbus unit ID, baud rate, BT pin etc.
Press 'set' twice in succession to exit.

note: baud rate 2400 & 19200 does not appear to work. 4800 & 9600 OK.

Program:

What can it do:

connect to serial port
switch output ON/OFF
set voltage & current levels
display voltage & current in chart
export voltage & current from chart as *.CSV
adjust brightness
lock hardware buttons
load, view and run *.CSV file (time, voltage & current)
Added battery charge capability

Serial port:

select baud rate (must match hardware configuration)
select slave address (must match hardware configuration)
Connect - automatically searches and connects to port (button status shows 'Connected' or 'Disconnected') (only tested in linux but should work with windows)
New feature - serial port can be fixed by modifying 'port_set' parameter within 'dps5005_limits.ini'

CSV

CSV now has 2 functions:

Preconfigured files can be imported to allow automated output control of the PSU. 'Sample.csv' is provided as an example. File -> Open, to load pre-configured *.CSV file, it then displays number of remaining steps. Select 'CSV run' to action the file. Select 'CSV clear' to remove unwanted remaining steps.
Imported CSV files can be viewed prior to Serial port connection using ‘CSV view’ button. This function is unavailable when Serial communications is established.

PSU

Basic Power supply mode

set Voltage limit
set Current limit
press 'Set' to load parameters then 'ON' to begin

Battery Charging

NiCad/NiMH - based on (-dV) negative delta V or better known as Peak Detect.

set absolute maximum safe charging voltage 'Voltage Max'
set 'Constant Current'
set 'Terminate (-dV)'
press 'Set' to load parameters then 'ON' to begin

Li-Ion/Lipo - based CCCV using taper current as termination.

set 'Constant Voltage'
set 'Constant Current'
set 'Terminate (A)'
press 'Set' to load parameters then 'ON' to begin

Note: Termination control begins 5seconds after charge start allowing current to stabilise.

Check out http://batteryuniversity.com for more information.

Disclaimer: User is responsible for safety. Program allows flexibility choose your values carefully.

Using other 'DPSxxxx' units

Configuring this program for other 'DPSxxxx' units should hopefully be straight forward to achieve by modifying the parameters within this file 'dps5005_limits.ini'.

adjust the safety levels, Max/Min values
adjust the decimal point position

Chart colours

The background, axis & pen colours and line (pen) width may be manipulated within the Section Three of the 'dps5005_limits.ini' file. Two examples exist.

background colour
axis colour
pen colour
pen weight

Requirements:

Python2

pip install pyserial
pip install MinimalModbus
pip install PyQt5
pip install pyqtgraph

if using python2.7: 
  pip install configparser

pip install -r requirements.txt

Python3

pip3 install pyserial
pip3 install MinimalModbus
pip3 install PyQt5
pip3 install pyqtgraph

pip3 install -r requirements.txt

Developed with:

dps_GUI.ui - QT designer v5.9.2
dps_GUI_program.py - Python 2.7.14
dps_modbus.py - Python 2.7.14
dps5005_limits.ini - text file

Download & run:

git clone https://github.com/lambcutlet/DPS5005_pyGUI

cd DPS5005_pyGUI/source_files/

python dps_GUI_program.py

python3 dps_GUI_program.py

szqt / DPS_pyGUI