Giters
synthetos
/
g2
g2core - The Next Generation
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
615
Watchers:
108
Issues:
410
Forks:
295
synthetos/g2 Issues
Project status
Updated
4 months ago
Comments count
5
Is G2core a good choice for my app?
Updated
a year ago
Wrong enum used for axis configuration
Updated
a year ago
Comments count
1
Spindle Enable Pin Not Functioning
Updated
a year ago
Comments count
1
bCNC - autolevel
Closed
a year ago
Comments count
1
Spiral roughing hiccup?
Closed
a year ago
Comments count
4
Is the g2core project still active?
Closed
a year ago
Comments count
1
Documentation is confusing and inconsistent regarding axis support
Closed
a year ago
Comments count
17
Status report not returning "pos" or "mpo" for A-axis
Closed
a year ago
Comments count
1
Compile g2core for gShield on Windows
Closed
a year ago
Comments count
3
Which version?
Closed
a year ago
Comments count
15
Endstops behaviour
Closed
a year ago
Comments count
9
Bad state after gpio input action stop
Closed
2 years ago
Comments count
3
UART on g2core
Updated
2 years ago
101.03 branch
Closed
2 years ago
Comments count
3
Arduino Due with Edge-preview+gShield not working ///'laser_tool' was not declared in this scope///
Closed
2 years ago
Comments count
4
feedrate interpretation for moves involving both, primary axes (XYZ) and secondary linear axes (UVW) differs from LinuxCNC
Updated
2 years ago
Spindle sometimes does not enable
Closed
3 years ago
Comments count
3
Skew correction ideas?
Closed
3 years ago
Comments count
4
Soft Limits not setting alarm state. Not stopping job.
Updated
3 years ago
Comments count
1
9 axis external driver board
Closed
3 years ago
Comments count
1
Error Compiling: Windows 10 Atmel Studio
Closed
3 years ago
Comments count
1
G-codes
Closed
3 years ago
Comments count
1
Not emitting steps at shallow incline.
Updated
3 years ago
Comments count
7
Serial UART Port
Updated
3 years ago
Comments count
1
E-Stop set-up on 100.26 and above compiled with gShield pinout?
Closed
3 years ago
Comments count
1
Edge: U,Y,W axes don't work in probe commands (G38.x)
Updated
3 years ago
Comments count
1
Homing on U,V or W axis is not possible
Updated
3 years ago
Comments count
36
Edge: axis names in text mode position reports (contains patch)
Updated
3 years ago
edge-preview: missing acceleration/deceleration when sending multiple moves at once
Updated
3 years ago
Comments count
1
G4 not dwelling with non-movement commands
Updated
4 years ago
Comments count
5
UVW Axis limit switches, documentation missing, configuration missing
Updated
4 years ago
Comments count
7
incorrect input pin state after glitch
Updated
4 years ago
Comments count
23
Status Report requested just before move starts sometimes reports target location rather than current location
Updated
4 years ago
Comments count
3
New “kill” behavior seems inconsistent with State Model for Feedhold and Job Kill (and bad location on hold)
Updated
4 years ago
Better jogging support
Updated
4 years ago
4th Axis Post Processor for Fusion 360
Updated
4 years ago
Comments count
6
Acceleration messed up after G38.2 probing
Closed
4 years ago
Comments count
3
Configure Spindle PWM Control on ArduinoDue gShield
Updated
4 years ago
Comments count
7
Adjust duration of step pin low state
Closed
4 years ago
Comments count
18
How can I compile firmware for a V9 board board153v9k?
Updated
4 years ago
Comments count
3
SPI API looks like overkill for simple startup config
Closed
4 years ago
Comments count
2
gShield pinout doesn't appear to match gShield
Closed
4 years ago
Comments count
4
PCB Auto Level Probing tripping
Updated
4 years ago
Comments count
1
Persistence of settings
Closed
4 years ago
Comments count
13
Feedrate not working
Closed
4 years ago
Comments count
6
motor control board for 4 motors (What are you guys using?)
Updated
4 years ago
Comments count
5
Question on feedrate config values
Closed
4 years ago
Comments count
3
how to use this with 5V stepper drivers?
Closed
4 years ago
Comments count
4
Question: motor configuration
Closed
4 years ago
Comments count
5
Previous
Next