simryang / rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959

rtl88x2bu driver updated for current kernels.

Deprecation notice. This repo is deprecated and a newer version of the driver is available at https://github.com/cilynx/rtl88x2bu

IPTIME 무선랜카드 A3000UA-2 드라이버입니다. 우분투 16.04용이구요 새로운 버전이 필요하신 분들은 위 주소로 가셔서 받으시면 됩니다...만 우분투 16.04에서 쓰실 분은 이 버전을 추천합니다. 직접 디버깅 가능하시면 최신 버전 쓰셔도 됩니다! 아래 영어 안내 읽기 싫으신 분은 https://simryang.tistory.com/entry/%EB%AC%B4%EC%84%A0-%EB%9E%9C%EC%B9%B4%EB%93%9C-IPTime-A3000UA-2-Ubuntu-1604-%EB%93%9C%EB%9D%BC%EC%9D%B4%EB%B2%84-%EC%84%A4%EC%B9%98%ED%95%98%EA%B8%B0 글을 참고 하시기 바랍니다.

Driver for rtl88x2bu wifi adaptors

Updated driver for rtl88x2bu wifi adaptors based on rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959 originally downloaded from D-Link's download page for the DWA-182 Rev D.

Build confirmed on:

Linux Q4 5.3.0-12-generic #13-Ubuntu SMP Tue Sep 17 12:35:50 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux

gcc (Ubuntu 9.2.1-8ubuntu1) 9.2.1 20190909

Linux xps 5.2.0-2-amd64 #1 SMP Debian 5.2.9-2 (2019-08-21) x86_64 GNU/Linux

gcc (Debian 9.2.1-8) 9.2.1 20190909

Linux 5.0.0-13-generic #14-Ubuntu SMP Mon Apr 15 14:59:14 UTC 2019 GNU/Linux

gcc (Ubuntu 8.3.0-6ubuntu1) 8.3.0

DKMS installation

cd rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959
VER=$(sed -n 's/\PACKAGE_VERSION="\(.*\)"/\1/p' dkms.conf)
sudo rsync -rvhP ./ /usr/src/rtl88x2bu-${VER}
sudo dkms add -m rtl88x2bu -v ${VER}
sudo dkms build -m rtl88x2bu -v ${VER}
sudo dkms install -m rtl88x2bu -v ${VER}
sudo modprobe 88x2bu

Raspberry Pi Access Point

# Update all packages per normal
sudo apt update
sudo apt upgrade

# Install prereqs
sudo apt install git dnsmasq hostapd bc build-essential dkms raspberrypi-kernel-headers

# Reboot just in case there were any kernel updates
sudo reboot

# Pull down the driver source
git clone https://github.com/cilynx/rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959.git
cd rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959/

# Configure for RasPi
sed -i 's/I386_PC = y/I386_PC = n/' Makefile
sed -i 's/ARM_RPI = n/ARM_RPI = y/' Makefile

# DKMS as above
VER=$(sed -n 's/\PACKAGE_VERSION="\(.*\)"/\1/p' dkms.conf)
sudo rsync -rvhP ./ /usr/src/rtl88x2bu-${VER}
sudo dkms add -m rtl88x2bu -v ${VER}
sudo dkms build -m rtl88x2bu -v ${VER} # Takes ~3-minutes on a 3B+
sudo dkms install -m rtl88x2bu -v ${VER}

# Plug in your adapter then confirm your new interface name
ip addr

# Set a static IP for the new interface (adjust if you have a different interface name or preferred IP)
sudo tee -a /etc/dhcpcd.conf <<EOF
interface wlan1
    static ip_address=192.168.4.1/24
    nohook wpa_supplicant
EOF

# Clobber the default dnsmasq config
sudo tee /etc/dnsmasq.conf <<EOF
interface=wlan1
  dhcp-range=192.168.4.100,192.168.4.199,255.255.255.0,24h
EOF

# Configure hostapd
sudo tee /etc/hostapd/hostapd.conf <<EOF
interface=wlan1
driver=nl80211
ssid=pinet
hw_mode=g
channel=7
wmm_enabled=0
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=2
wpa_passphrase=CorrectHorseBatteryStaple
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
EOF

sudo sed -i 's|#DAEMON_CONF=""|DAEMON_CONF="/etc/hostapd/hostapd.conf"|' /etc/default/hostapd

# Enable hostapd
sudo systemctl unmask hostapd
sudo systemctl enable hostapd

# Reboot to pick up the config changes
sudo reboot

If you want to setup masquerading or bridging, check out the official Raspberry Pi docs.