Giters

sergiopantoja / DIY-Air-Purifier

A small DIY air purifier using off-the-shelf components for under $100

Geek Repo:Geek Repo

Github PK Tool:Github PK Tool

DIY-Air-Purifier

A small DIY air purifier using off-the-shelf components for <$100.

Time to assemble this project - 1hr (not including 3D print time).

Uses a 3D printed housing so you'll need a printer or access to one. You could use a printing service such as 3D Hubs.

All prices listed are in AUD.

Background

In the summer of 2019/2020 Australia is experiencing unprecedented dangerous fire conditions driven by climate change. Much of the east coast of the country south of Brisbane is engulfed in deadly bushfires and air pollution ratings in cities such as Sydney, Canberra, Melbourne and many other regional cities and towns is many times the recommended safe levels of PM2.5 particles. The long term affects of the inhalation of bushfire smoke is mostly unknown at this time, but already people have died from respiratory distress bought about by the smoke-filled air.

There has been a great deal of discussion online and in the media about the use of P2 respirators and home air purifiers to reduce the effects of the bushfire smoke. However, information about the efficiacy of P2 respirators for bushfire smoke is not readily available and what information can be found suggests they may be of limited use. Health officials are continuing to recommend eliminating exposure to PM2.5 particles and bushfire smoke-related chemicals by remaining indoors if possible. Unfortunately for many people the summer heat makes indoors extremely uncomfortable and the evaporative air conditioners installed in many homes in my state of Victoria do not filter the damaging PM2.5 particles from the air. Health officials recommend using HEPA H13 air purifiers, however these are extremely expensive with even a basic unit suitable for a single room costing around $500.

With all this in mind I set about finding a way to build a low-cost, effective air purifier that would meet the minimum requirement to filter PM2.5 particles in a bedroom, so that children and at-risk people could at least sleep without inhaling these dangerous airborne contaminants.

This github sets out the process I followed to construct and test the device, as well as the BOM and 3D print STL files for recreating the device.

Purpose

The purpose of this project is to create a small air purifier suitable for a bedroom or caravan (or similar sized space) that meets the following critiera:

  • Costs under $100 to build (in parts);
  • Can be constructed with relatively low levels of technical skill (there is soldering of two wires required);
  • Uses off-the-shelf components available in most Australian cities, or by order over the internet from Australian suppliers; and
  • Uses a HEPA H13 rated filter; and
  • Is powered from a commonly available USB powerbank.

Method

I selected a readily available HEPA H13 rated filter normally used in cheap vacuum cleaners and available from Bunnings Warehouse. The rest of the air purifier is based around that filter. I then selected a range of 120mm computer fans with relatively high static pressure ratings (>2.0 mmAq) that could operate on 12vDC. As the fans are 12vDC I used a USB 'booster cable' which steps-up the voltage of any USB-A port from 5v to 12v; these cables are available online or from a range of electronics shops such as Jaycar. After selecting the components I then designed a fan housing using Fusion 360 that provides the interface between the 120mm and the HEPA filter. The filter comes with a removable seal/cover at one end, so I use that end as the base of the unit and fit the fan to the top. After basic testing with a small smoke generator to ensure the selected fans could draw air through the filter to a reasonable standard I have determined the project suitable for release so others can create their own version of this device both for use in their homes and for further testing.

The image above shows the rendered view of the device from Fusion 360 with an iPhone X for scale. The first version of the housing used a separate fan grill but I was able to eliminate this by incorporating the hex pattern into the housing, which also saved about $7 off the cost.

Materials

The BOM for the air purifier is:

3D printing notes

Just a couple of notes about the 3D print files.

  • I designed the fan housing using Fusion 360 and exported STLs from there.
  • I tweaked the design a number of times to get it to print easily on my Ultimaker 2+. You'll see in the images here (the magenta housing) an early version where the edges curled up badly. I recommend you print with a brim and a heated buildplate as that's what I have used.
  • If you have a printer with a smaller buildplate I have included a folder in 3D_print_files with a version of the housing I split into 4 so it can be printed in parts then glued together. I have not tested this print at all so if you do print it please let me know how it goes. If there are changes required that's easily done.
  • I've been printing in PLA with no requirement for supports on the default Cura settings for Ultimaker PLA, except I turn down the buildplate temp to 50ºc after the first layer, which helps prevent the edges curling. If you print in other materials then let me know how it goes.

Tools

You will need the following tools to assemble the device:

  • Soldering iron and solder
  • Pliers (with wire cutters)
  • Scissors
  • Multimeter (to determine correct polarity for the wiring of the socket)

Assembly

Step 1

Assemble the wiring harness for the 2.5mm socket.

  • Take the 4pin fan cable and cut one of the female plugs off leaving about 10cm of cable on the plug.
  • Trim back the cable protective sleeve with the scissors leaving about 2cm of exposed wires.
  • If you use the cable I linked above to make this harness you need the orange (+) and black (-) wires, other cables may differ so check before you go further you have the correct wires.
  • Keeping the orange and black wires the length you cut previously, cut the other two wires off shorter so they will be inside the cable sheath and out of the way.
  • Strip and tin the orange and black wires with new 60/40 solder and place on the heatshrink tubing over the top of the cable protective sheath.
  • Determine the correct terminal lugs on the 2.5mm socket using the multimeter. Then solder the + and - wires to the correct terminals.
  • Pull the heatshrink over the socket lugs and shrink it with a heat gun or flame.
  • The completed wiring harness should look similar to this

Step 2

Assemble the fan housing.

  • Take the 3D printed housing and insert the 2.5mm socket from the inside, and fix in place using the supplied washer and nut. Tighten down with your pliers so it is snug but don't go crazy, you don't want to crack the housing.
  • Place the fan inside the housing with the writing facing towards the square end, this will ensure the fan draws air through the filter rather than pushing air into the filter. It wont make a huge difference to the performance of the device, but it's good practice to have clean air running over the fan. Use the 4 rubber fan mounts (or bolts if you use that method) to fix the fan into the case, then plug the fan cable into the wiring harness from step 1.

Step 3

Assemble the device.

  • Take the fan housing assembly and place it over the open end of the HEPA filter, taking care to work around the edge of the rubber ring on the filter itself so a good seal is make on the inside of the housing.
  • Ensure the base cover is installed firmly in the filter housing. (note the images below are of an early version with no integrated fan grill, the assembly is identical otherwise. I'll update these with better images later)

Step 4

Power up and test.

  • Assemble the USB cable with the 2.5mm plug. In the kit linked above it is the largest suppled plug, with the white tip.

  • Plug the cable into the device and your USB power bank and the fan should start running. If the fan doesn't work you should begin troubleshooting. Start with checking your powerbank is charged and turned on to supply power. I have a couple of battery packs that don't work to supply power to the air purifier, even though they are rated well above the requirement, I'm not sure why but it seems like some devices can't supply the surge current required to start the fan.

  • Note that not all power banks can support pass-through charging and depending on the fan you select you may find the pack cannot charge faster than you run it down. The more expensive fan I linked above will draw around 1amp or a little above, and if you use this fan you need to make sure your charger can supply above 1amp (comfortably) to keep your battery charged. The power bank in the image below is one I use for testing in my office, it's not suitable to run the device for long periods.

Initial test results

As I'm using a HEPA H13 rated filter I'm not concerned with the ability of the device to remove PM2.5 particles, that's implied in the rating of the filter. My main concern is how effective the device is at air exchange in a small room. In order to work out if the device was working to draw air through the filter I set up a small test with the device inside a plastic box that I filled with smoke from a 'disco' smoke machine. Running the device inside the box showed that it was in fact pulling air through the filter and removing this smoke. The 1000% speed gif below shows a test where I filled the box with smoke and left it for 2min (to make sure the smoke wasn't just leaking away) then activated the device for 90sec, as you can see the device filters out the smoke pretty quickly.

After determining the device did pull air through the filter I set up another test where I used the airspeed sensor from a drone (I have drones) to do a rough calculation of the CFM of the device. I used a pixracer flight controller to process the airspeed data and read it using Mission Planner - this is all drone-speak for anyone interested in that part of the test. One of the prototype housings was drilled and I printed a sleeve for the pitot tube that I hot-glued into the housing so the pitot would be in the airstream at the correct angle.

This is a very rough test because the airspeed sensor is not properly calibrated (just zeroed before the test), although I also checked the results by using a handheld anemometer and got pretty much the same readings. So from this test I calculated a CFM of ~160 using the larger of the two fans, which is rated (on the packaging) at 186 CFM, so it seems like this result is probably about right. I have an open issue for assistance with doing a more rigorous test, so if you have the equipment and/or knowledge for this please get in touch.

The rudimentary testing indicates that in my home office (25m3) the device with the larger fan is able to achieve about 10 air exchanges per hour, which would be a good result for this sized space. I'm not confident this is accurate though, but it at least indicates that air exchange is taking place, and it's in the ballpark of a small commercial air purifier.

Final remarks

This is a DIY project requiring basic skills including soldering. Selecting an appropriate power supply will require some basic knowledge of electricity. I've tried to keep everything as simple as possible and this isn't a consumer-grade product. Other than testing to ensure the fan drew air through the filter I have not tested this device for effectivenes in filtering harmful airborne contaminants. You should build and use this device at your own risk, no liability is implied or accepted.

Request for assistance

If you can assist with improving this project by more rigorous testing using a PM2.5 meter or other instrumentation then please get in touch with me at info@phasezero.com.au or via this repo.

Licence

This work is licenced under a Attribution-NonCommercial-ShareAlike 3.0 Australia licence. https://creativecommons.org/licenses/by-nc-sa/3.0/au/

About

A small DIY air purifier using off-the-shelf components for under $100