Raspberry Pi Cluster

This repository contains examples and automation used in various Raspberry Pi clustering scenarios, as seen on Jeff Geerling's YouTube channel.

The inspiration for this project was my first Pi cluster, the Raspberry Pi Dramble, which is still running in my basement to this day!

Usage

Make sure you have Ansible installed.
Copy the example.hosts.ini inventory file to hosts.ini. Make sure it has the control_plane and nodes configured correctly (for my examples I named my nodes node[1-4].local).
Copy the example.config.yml file to config.yml, and modify the variables to your liking.

Raspberry Pi Setup

I am running Raspberry Pi OS on various Pi clusters. You can run this on any Pi cluster, but I tend to use Compute Modules without eMMC ('Lite' versions) and I often run them using 32 GB SanDisk Extreme microSD cards to boot each node. For some setups (like when I run the Compute Blade or DeskPi Super6c, I boot off NVMe SSDs instead.

In every case, I flashed Raspberry Pi OS (64-bit, lite) to the storage devices using Raspberry Pi Imager.

To make network discovery and integration easier, I edit the advanced configuration in Imager, and set the following options:

Set hostname: node1.local (set to 2 for node 2, 3 for node 3, etc.)
Enable SSH: 'Allow public-key', and paste in my public SSH key(s)
Configure wifi: (ONLY on node 1, if desired) enter SSID and password for local WiFi network

After setting all those options, making sure only node 1 has WiFi configured, and the hostname is unique to each node (and matches what is in hosts.ini), I inserted the microSD cards into the respective Pis, or installed the NVMe SSDs into the correct slots, and booted the cluster.

SSH connection test

To test the SSH connection from my Ansible controller (my main workstation, where I'm running all the playbooks), I connected to each server individually, and accepted the hostkey:

ssh pi@node1.local

This ensures Ansible will also be able to connect via SSH in the following steps. You can test Ansible's connection with:

ansible all -m ping

It should respond with a 'SUCCESS' message for each node.

Storage Configuration

This playbook will create a storage location on node 3 by default. You can use one of the storage configurations by switching the storage_type variable from filesystem to zfs in your config.yml file.

Filesystem Storage

If using filesystem (storage_type: filesystem), make sure to use the appropriate storage_nfs_dir variable in config.yml.

ZFS Storage

If using ZFS (storage_type: zfs, you should have two volumes available on node 3, /dev/sda, and /dev/sdb, able to be pooled into a mirror. Make sure your two SATA drives are wiped:

pi@node3:~ $ sudo wipefs --all --force /dev/sda?; sudo wipefs --all --force /dev/sda
pi@node3:~ $ sudo wipefs --all --force /dev/sdb?; sudo wipefs --all --force /dev/sdb

If you run lsblk, you should see sda and sdb have no partitions, and are ready to use:

pi@node3:~ $ lsblk
NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
sda           8:0    0  1.8T  0 disk 
sdb           8:16   0  1.8T  0 disk

You should also make sure the storage_nfs_dir variable is set appropriately for ZFS in your config.yml.

This ZFS layout was configured originally for the Turing Pi 2 board, which has two built-in SATA ports connected directly to node 3. In the future, the configuration may be genericized a bit better.

Ceph Storage Configuration

You could also run Ceph on a Pi cluster—see the storage configuration playbook inside the ceph directory.

This configuration is not yet integrated into the general K3s setup.

Cluster configuration and K3s installation

Run the playbook:

ansible-playbook main.yml

At the end of the playbook, there should be an instance of Drupal running on the cluster. If you log into node 1, you should be able to access it with curl localhost.

If the playbook stalls while installing K3s, you might need to configure static IP addresses for the nodes, especially if using mDNS (like with .local names for the nodes). Follow the guide in "Static network configuration" then run the main.yml playbook again afterwards, and it should get things in order.

If you have SSH tunnelling configured (see later section), you could access http://[your-vps-ip-or-hostname]:8080/ and you'd see the site.

You can also log into node 1, switch to the root user account (sudo su), then use kubectl to manage the cluster (e.g. view Drupal pods with kubectl get pods -n drupal).

The Kubernetes Ingress object for Drupal (how HTTP requests from outside the cluster make it to Drupal) can be found by running kubectl get ingress -n drupal. Take the IP address or hostname there and enter it in your browser on a computer on the same network, and voila! You should see Drupal's installer.

K3s' kubeconfig file is located at /etc/rancher/k3s/k3s.yaml. If you'd like to manage the cluster from other hosts (or using a tool like Lens), copy the contents of that file, replacing localhost with the IP address or hostname of the control plane node, and paste the contents into a file ~/.kube/config.

Upgrading the cluster

Run the upgrade playbook:

ansible-playbook upgrade.yml

Monitoring the cluster

Prometheus and Grafana are used for monitoring. Grafana can be accessed via port forwarding (or you could choose to expose it another way).

To access Grafana:

Make sure you set up a valid ~/.kube/config file (see 'K3s installation' above).
Run kubectl port-forward service/cluster-monitoring-grafana :80
Grab the port that's output, and browse to localhost:[port], and bingo! Grafana.

The default login is admin / prom-operator, but you can also get the secret with kubectl get secret cluster-monitoring-grafana -o jsonpath="{.data.admin-password}" | base64 -D.

You can then browse to all the Kubernetes and Pi-related dashboards by browsing the Dashboards in the 'General' folder.

Benchmarking the cluster

See the README file within the benchmarks folder.

Shutting down the cluster

The safest way to shut down the cluster is to run the following command:

ansible all -m community.general.shutdown -b

Note: If using the SSH tunnel, you might want to run the command first on nodes 2-4, then on node 1. So first run ansible 'all:!control_plane' [...], then run it again just for control_plane.

Then after you confirm the nodes are shut down (with K3s running, it can take a few minutes), press the cluster's power button (or yank the Ethernet cables if using PoE) to power down all Pis physically. Then you can switch off or disconnect your power supply.

Static network configuration (highly recommended)

Kubernetes generally likes static network routes, especially when using DNS to connect to other nodes in a cluster.

There is a playbook which configures static networking so your nodes maintain the same IP address after a reboot, even under different networking scenarios.

If using your cluster both on-premise and remote (e.g. using 4G LTE connected to the first Pi), you can set it up on its own subnet (e.g. 10.1.1.x). Otherwise, you can set it to the same subnet as your local network.

Configure the subnet via the ipv4_subnet_prefix variable in config.yml, then run the playbook:

ansible-playbook networking.yml

After running the playbook, until a reboot, the Pis will still be accessible over their former DHCP-assigned IP address. After rebooting, the nodes will be accessible on their new IP addresses.

You can reboot all the nodes with:

ansible all -m reboot -b

If you are running Ubuntu, and you get an error like "Failed to find required executable "nmcli", run the ubuntu-setup.yml playbook: ansible-playbook tasks/networking/ubuntu-prep.yml

If using a different subnet

If you chose a different subnet than your LAN, make sure your workstation is connected to an interface on the same subnet as the cluster (e.g. 10.1.1.x).

After the networking changes are made, since this playbook uses DNS names (e.g. node1.local) instead of IP addresses, your computer will still be able to connect to the nodes directly—assuming your network has IPv6 support. Pinging the nodes on their new IP addresses will not work, however. For better network compatibility, it's recommended you set up a separate network interface on the Ansible controller that's on the same subnet as the Pis in the cluster:

On my Mac, I connected a second network interface and manually configured its IP address as 10.1.1.10, with subnet mask 255.255.255.0, and that way I could still access all the nodes via IP address or their hostnames (e.g. node2.local).

Because the cluster subnet needs its own router, node 1 is configured as a router, using wlan0 as the primary interface for Internet traffic by default. The other nodes get their Internet access through node 1.

Switch between 4G LTE and WiFi (optional)

The network configuration defaults to an active_internet_interface of wlan0, meaning node 1 will route all Internet traffic for the cluster through it's WiFi interface.

Assuming you have a working 4G card in slot 1, you can switch node 1 to route through an alternate interface (e.g. usb0):

Set active_internet_interface: "usb0" in your config.yml
Run the networking playbook again: ansible-playbook networking.yml

You can switch back and forth between interfaces using the steps above.

Reverse SSH and HTTP tunnel configuration (optional)

For my own experimentation, I ran my Pi cluster 'off-grid', using a 4G LTE modem, as mentioned above.

Because my mobile network provider uses CG-NAT, there is no way to remotely access the cluster, or serve web traffic to the public internet from it, at least not out of the box.

I am using a reverse SSH tunnel to enable direct remote SSH and HTTP access. To set that up, I configured a VPS I run to use TCP Forwarding (see this blog post for details), and I configured an SSH key so node 1 could connect to my VPS (e.g. ssh my-vps-username@my-vps-hostname-or-ip).

Then I set the reverse_tunnel_enable variable to true in my config.yml, and configured the VPS username and hostname options.

Doing that and running the main.yml playbook configures autossh on node 1, and will try to get a connection through to the VPS on ports 2222 (to node 1's port 22) and 8080 (to node 1's port 80).

After that's done, you should be able to log into the cluster through your VPS with a command like:

$ ssh -p 2222 pi@[my-vps-hostname]

Note: If autossh isn't working, it could be that it didn't exit cleanly, and a tunnel is still reserving the port on the remote VPS. That's often the case if you run sudo systemctl status autossh and see messages like Warning: remote port forwarding failed for listen port 2222.

In that case, log into the remote VPS and run pgrep ssh | xargs kill to kill off all active SSH sessions, then autossh should pick back up again.

Warning: Use this feature at your own risk. Security is your own responsibility, and for better protection, you should probably avoid directly exposing your cluster (e.g. by disabling the GatewayPorts option) so you can only access the cluster while already logged into your VPS).

Caveats

These playbooks are used in both production and test clusters, but security is always your responsibility. If you want to use any of this configuration in production, take ownership of it and understand how it works so you don't wake up to a hacked Pi cluster one day!

Author

The repository was created in 2023 by Jeff Geerling, author of Ansible for DevOps, Ansible for Kubernetes, and Kubernetes 101.

r3dlobst3r / mini-cluster