该项目主要是出于个人兴趣，将原生的GRBL的源码，移植到STM32的MCU上，移植的源码的地址：https://github.com/gnea/grbl
目前该项目还未完善，主要原因是因为电机控制部分还未完全调试完成，其余完成的部分：
- GPIO，读写操作和中断，用于限位和Probe
- UART，用于上位机连接，目前与上位机正常连接
- EEPROM，读写与保存正常
- W25qxx，驱动已经正常，后期可以针对GUI，用于图片存放和字库存放
- SDCard, 未加入， 用于脱机
- TFT_SPI，未完成，用于脱机显示和操作
- Spindle，已完成
- FreeRTOS, 已移植完成
- Fatfs, 已加入
测试方法是在保持工程结构不改变的前提下，只修改了底层接口，其余地方不改变，
| 内核 | MCU型号 |
|---|---|
| @Cortex-M0 | STM32G070RB |
| @Cortex-M0 | STM32G0B0CE |
| @Cortex-M3 | STM32F103VE |
| @Cortex-M4 | STM32F429IG |
| @Cortex-M7 | STM32H750XB/i.MX RT1064/i.MX RT1010-EVK |
目前Vscode+PlatformIO的环境已经搭建完成，抛弃了Keil的环境，Keil环境的代码将会移植到PIO中执行。
参数与标准GRBL一致
| $0 | Step pulse time | 10 | microseconds | Sets time length per step. Minimum 3usec. |
|---|---|---|---|---|
| $1 | Step idle delay | 25 | milliseconds | Sets a short hold delay when stopping to let dynamics settle before disabling steppers. Value 255 keeps motors enabled with no delay. |
| $2 | Step pulse invert | 0 | mask | Inverts the step signal. Set axis bit to invert (00000ZYX). |
| $3 | Step direction invert | 0 | mask | Inverts the direction signal. Set axis bit to invert (00000ZYX). |
| $4 | Invert step enable pin | 0 | boolean | Inverts the stepper driver enable pin signal. |
| $5 | Invert limit pins | 0 | boolean | Inverts the all of the limit input pins. |
| $6 | Invert probe pin | 0 | boolean | Inverts the probe input pin signal. |
| $10 | Status report options | 1 | mask | Alters data included in status reports. |
| $11 | Junction deviation | 0.010 | millimeters | Sets how fast Grbl travels through consecutive motions. Lower value slows it down. |
| $12 | Arc tolerance | 0.002 | millimeters | Sets the G2 and G3 arc tracing accuracy based on radial error. Beware: A very small value may effect performance. |
| $13 | Report in inches | 0 | boolean | Enables inch units when returning any position and rate value that is not a settings value. |
| $20 | Soft limits enable | 0 | boolean | Enables soft limits checks within machine travel and sets alarm when exceeded. Requires homing. |
| $21 | Hard limits enable | 1 | boolean | Enables hard limits. Immediately halts motion and throws an alarm when switch is triggered. |
| $22 | Homing cycle enable | 1 | boolean | Enables homing cycle. Requires limit switches on all axes. |
| $23 | Homing direction invert | 0 | mask | Homing searches for a switch in the positive direction. Set axis bit (00000ZYX) to search in negative direction. |
| $24 | Homing locate feed rate | 25.000 | mm/min | Feed rate to slowly engage limit switch to determine its location accurately. |
| $25 | Homing search seek rate | 500.000 | mm/min | Seek rate to quickly find the limit switch before the slower locating phase. |
| $26 | Homing switch debounce delay | 250 | milliseconds | Sets a short delay between phases of homing cycle to let a switch debounce. |
| $27 | Homing switch pull-off distance | 1.000 | millimeters | Retract distance after triggering switch to disengage it. Homing will fail if switch isn't cleared. |
| $30 | Maximum spindle speed | 1000 | RPM | Maximum spindle speed. Sets PWM to 100% duty cycle. |
| $31 | Minimum spindle speed | 0 | RPM | Minimum spindle speed. Sets PWM to 0.4% or lowest duty cycle. |
| $32 | Laser-mode enable | 0 | boolean | Enables laser mode. Consecutive G1/2/3 commands will not halt when spindle speed is changed. |
| $100 | X-axis travel resolution | 80.000 | step/mm | X-axis travel resolution in steps per millimeter. |
| $101 | Y-axis travel resolution | 80.000 | step/mm | Y-axis travel resolution in steps per millimeter. |
| $102 | Z-axis travel resolution | 80.000 | step/mm | Z-axis travel resolution in steps per millimeter. |
| $110 | X-axis maximum rate | 6000.000 | mm/min | X-axis maximum rate. Used as G0 rapid rate. |
| $111 | Y-axis maximum rate | 6000.000 | mm/min | Y-axis maximum rate. Used as G0 rapid rate. |
| $112 | Z-axis maximum rate | 6000.000 | mm/min | Z-axis maximum rate. Used as G0 rapid rate. |
| $120 | X-axis acceleration | 500.000 | mm/sec^2 | X-axis acceleration. Used for motion planning to not exceed motor torque and lose steps. |
| $121 | Y-axis acceleration | 500.000 | mm/sec^2 | Y-axis acceleration. Used for motion planning to not exceed motor torque and lose steps. |
| $122 | Z-axis acceleration | 500.000 | mm/sec^2 | Z-axis acceleration. Used for motion planning to not exceed motor torque and lose steps. |
| $130 | X-axis maximum travel | 200.000 | millimeters | Maximum X-axis travel distance from homing switch. Determines valid machine space for soft-limits and homing search distances. |
| $131 | Y-axis maximum travel | 200.000 | millimeters | Maximum Y-axis travel distance from homing switch. Determines valid machine space for soft-limits and homing search distances. |
| $132 | Z-axis maximum travel | 200.000 | millimeters | Maximum Z-axis travel distance from homing switch. Determines valid machine space for soft-limits and homing search distances. |
- 编译器使用：Vscode+PlatformIO
- 下载和调试工具使用：Jlink/DAPlink(OpenOCD)