The PAM U2F module provides an easy way to integrate the Yubikey (or other U2F-compliant authenticators) into your existing user authentication infrastructure. PAM is used by GNU/Linux, Solaris and Mac OS X for user authentication.
This module implements PAM authentication over U2F. Registration should be performed using the included tool. Multiple devices are supported, for details check the Multiple Devices section.
For more information visit the project page pam-u2f project.
The project is licensed under a BSD license. See the file COPYING for exact wording. For any copyright year range specified as YYYY-ZZZZ in this package note that the range specifies every single year in that closed interval.
This project uses autoconf, automake and libtool to achieve portability and ease of use. If you downloaded a tarball, build it as follows.
$ ./configure $ make check
Both the Yubico U2F host and server libaries are needed libu2f-host, libu2f-server
You may check out the sources using Git with the following command:
$ git clone git://github.com/Yubico/pam-u2f.git
This will create a directory pam-u2f. Enter the directory:
$ cd pam-u2f
Autoconf, automake, libtool, and libpam must be installed. AsciiDoc and xsltproc are used to generate the manpages.
Debian: apt-get install autoconf automake libtool libpam-dev asciidoc xsltproc --no-install-recommends
Generate the build system using:
$ autoreconf --install
Then build as usual, see above under Building.
Once the module is built copy the file pam_u2f.so
to the correct
directory for your system. Typically /lib/security/
or
/lib/x86_64-linux-gnu/security/
.
Create a file for a new service in /etc/pam.d/
or edit an already
existing one by adding a line similar to this:
auth sufficient pam_u2f.so debug
Supported parameters for the module are:
debug |
Turns on debugging to STDOUT |
origin=origin |
Set the origin for the U2F authentication procedure. If no value is specified, the origin "pam://$HOSTNAME" is used. |
appid=appid |
Set the application ID for the U2F authentication procedure. If no value is specified, the same value used for origin is taken ("pam://$HOSTNAME" if also origin is not specified). |
authfile=file |
Set the location of the file that holds the mappings of user names
to keyHandles and user keys. The format is
|
nouserok |
Set to enable authentication attempts to succeed even if the user trying to authenticate is not found inside authfile. |
alwaysok |
Set to enable all authentication attempts to succeed (aka presentation mode). |
max_devices=n_devices |
Maximum number of devices allowed per user (default is 24). Devices specified in the authentication file that exceed this value will be ignored. |
A mapping must be made between the YubiKey token and the user name. There are two ways to do this, either centrally in one file, or individually, where users can create the mapping in their home directories. If the central authorization mapping file is being used, user home directory mappings will not be used and the opposite applies if user home directory mappings are being used, the central authorization mappings file will not be used.
Create a file e.g. /etc/u2f_mappings
., The file must contain
a user name, the number of registered Yubikeys and the information
obtained during the registration procedure.
The mappings should look like this, one per line:
<username1>:<KeyHandle1>,<UserKey1>:<KeyHandle2>,<UserKey2>:... <username2>:<KeyHandle1>,<UserKey1>:<KeyHandle2>,<UserKey2>:...
Now add authfile=/etc/u2f_mappings
to your PAM configuration line, so it
looks like:
auth sufficient pam_u2f.so authfile=/etc/u2f_mappings
Each user creates a ~/config/Yubico/u2f_keys
file inside of their home
directory and places the mapping in that file, the file must have only one
line:
<username>:<KeyHandle1>,<UserKey1>:<KeyHandle2>,<UserKey2>:...
This is much the same concept as the SSH authorized_keys file.
In order to obtain the required information for the authentication procedure, a token should be first registered. This can be done by using the command line configuration tool provided with the module:
$ pamu2fcfg -uusername -opam://myorigin \ -ipam://myappid
the tool will register a connected token by using the specified origin and
appid. If neither are specified they will default to pam://$HOSTNAME
.
During the U2F registration, the user is required to touch the token.
On success the tool prints to standard output a configuration line that
can be directly used with the module. For additional information on the
tool read the relative manpage (man pamu2fcfg
)
Multiple devices are supported. If more than one device is specified, authentication against them is attempted sequentially as they are defined in the configuration file of the module. If during an authentication attempt a connected device is removed or a new device is plugged in, the authentication restarts from the top of the list.