This bundle is a selection of effects I've made over the years to make my own music production process easier. The tools can be roughly divided into three groups: EFX, Mixing Tools and Mastering Tools. All effects have a scalable user interface and most parameters can be automated.
Dedicated to a little crow that left the world too early.
Probably the effect of this bundle that is the hardest to describe.
In very technical terms: it makes a copy of your input and mixes it with the input after the amount of milliseconds you set. You can define how much the signal is shifted between the left and right channel and add edge to it which manipulates the delayed signal based on the current input.
In less technical terms: it makes weird effects by messing around with a very short delay superimposed on the input signal - just give it a shot and you'll get a better idea than I can describe.
A BPM-driven delay that makes use of stereo effects and allows you to blend forward and reverse delays using an XY-pad.
The name says it, it tries to automatically pan your signal.
Being able to control the phase of a signal allows you to create a wide range of effects but it also enables you to employ some simple mixing tricks. For example: a kick and a bass guitar often overlap in the low end, so you have to do extra EQing to keep them separated. With Phase Control you can achieve the same without EQing by rotating the phase a few degrees, sometimes it doesn't need more than one degree to have bass guitar and kick neatly separated.
The rotation is controlled via an XY-pad that allows you to mix the sine and cosine components of a phase rotation any way you like it. The cleanest sound is achieved if both components are represented equally, shifting them will add a different character to your signal. Besides rotating the phase you can also invert it, again controlled via an XY-pad. The inversion can be anything from 0% to 100%, left and right channel are treated independently.
This allows you to pan and mix your input signal with either the mid or the side signal which allows a wide range of manipulation for your stereo field. Useful for spatial effects, mix separation and audio restoration.
Wanna mess with your stereo signal? Well, here you go. This can be useful to widen a signal, or to add some noise to it, or to do both at once. Primarily it's meant to be used sparingly to enhance the stereo field, but no-one stops you from going wild with that.
Admit it, sometimes you just want to know what your audio looks like, right? Well, I do because that helps me to hone in on problems and it looks cool, too. This plugin is the third generation of my AudioAnalyzers (v1, v2). I've rebuild all components to be scalable and make as much use as possible of the available space. As such you can scale it to a small size where it will only show a spectrum, the history of phase, left and right signal, and a goniometer. But scale it up and it will also display a spectrogram. If you hover your mouse over the spectrum and spectrogram you can see some information about that spot like frequency, tone name and current volume. If you click and keep your mouse button pressed it will show you markers for overtones which you can, for example, use to find dominant frequencies / tones.
Uses a couple of tricks to allow you to boost a signal by quite a bit without applying actual compression. It does use a very little to limit the output to -0.1 dB, but not for the actual boosting. Via an XY-pad you can control the sonic character and balance the high and low end of your signal. Besides that the Boom Control shifts infrasound ranges of the input into the audible low end which increases clarity without losing low end punch (a side effect that can occur when simply removing the infrasound frequencies). Untested, but this might be very useful for vinyl mastering.
This removes infrasound (< 20 Hz) and ultrasound (> 20 kHz) from your signal. Unless you want to make your listeners feel unwell there is no reason to keep these frequencies, filtering them increases clarity and reduces problems that appear when playing your audio through different stereo sets.
In REAPER open the Options menu and select Show REAPER resource path in explorer/finder.... This will open the directory where your REAPER installation lives. Open the directory Effects and drop the effects in there. It is a good idea to keep them in directories like in the repo, so you can install different versions and use them side by side in case of changes that break backwards compatibility.
Because it became tedious work to make nice UIs for the effects (as there are no components like buttons or checkboxes or ...) I decided to design my own version of REAPER's JSFX language, simply called JSFX-E(xtended). I've added support for libraries and objects, project configuration via JSON files and a grid-based UI framework for UIs that can scale to any resolution without changes to the code or complex calculations.
Everything I've added to the language is designed to work well with the syntax highlighting of the Sublime Text 3 plugin ReaSyntax and code folding, some parts of it will look like standard JSFX and others may look weird at first sight, especially in the @gfx section.
Obviously REAPER does not understand these extensions, so I also made a compiler that generates a single file with JSFX code per effect. All the code you see in this repo is generated and the original project source files are typically about 1000 lines shorter. During compilation a lot of short hands will be expanded to JSFX syntax (typical regular expression work), objects will be generated, and the UI definition will be parsed. At the end of the process the compiler tries to remove all unused functions to reduce the code size. In some cases there will be leftovers, though. These are from static classes that are referenced by libraries but never used. Since the functions in question are never called it's not an issue for the performance, but if you read the code you might stumble upon a few things that are unused.