Btrfs maintenance toolbox
Table of contents:
This is a set of scripts supplementing the btrfs filesystem and aims to automate a few maintenance tasks. This means the scrub, balance, trim or defragmentation.
Each of the tasks can be turned on/off and configured independently. The default config values were selected to fit the default installation profile with btrfs on the root filesystem.
Overall tuning of the default values should give a good balance between effects of the tasks and low impact of other work on the system. If this does not fit your needs, please adjust the settings.
scrub
Description: Scrub operation reads all data and metadata from the devices and verifies the checksums. It's not mandatory, but may point out problems with faulty hardware early as it touches data that might not be in use and bitrot.
If thre's a redundancy of data/metadata, ie. the DUP or RAID1/5/6 profiles, scrub is able to repair the data autmatically if there's a good copy available.
Impact when active: Intense read operations take place and may slow down or block other filesystem activies, possibly only for short periods.
Tuning:
- the recommended period is once in a month but a weekly period is also acceptable
- you can turn off the automatic repair (
BTRFS_SCRUB_READ_ONLY
) - the default IO priority is set to idle but scrub may take long to finish,
you can change priority to normal (
BTRFS_SCRUB_PRIORITY
)
Related commands:
- you can check status of last scrub run (either manual or through the cron
job) by
btrfs scrub status /path
- you can cancel a running scrub anytime if you find it inconvenient (
btrfs scrub cancel /path
), the progress state is saved each 5 seconds and next time scrub will start from that point
balance
Description: The balance command can do a lot of things, in general moves data around in big chunks. Here we use it to reclaim back the space of the underused chunks so it can be allocated again according to current needs.
The point is to prevent some corner cases where it's not possible to eg. allocate new metadata chunks because the whole device space is reserved for all the chunks, although the total space occupied is smaller and the allocation should succeed.
The balance operation needs enough workspace so it can shuffle data around. By
workspace we mean device space that has no filesystem chunks on it, not to be
confused by free space as reported eg. by df
.
Impact when active: Possibly big. There's a mix of read and write operations, is seek-heavy on a rotational devices. This can interfere with other work in case the same set of blocks is affected.
The balance command uses filters to do the work in smaller batches.
Expected result: If possible all the underused chunks are removed, the
value of total
in output of btrfs fi df /path
should be lower than before.
Check the logs.
The balance command may fail with no space reason but this is considered a minor fault as the internal filesystem layout may prevent fhe command to find enough workspace. This might be a time for manual inspection of space.
Tuning:
- you can make the space reclaim more aggressive by adding higher percentage to
BTRFS_BALANCE_DUSAGE
orBTRFS_BALANCE_MUSAGE
. Higher value means bigger impact on your system and becomes very noticeable. - the metadata chunks usage pattern is different from data and it's not necessary to reclaim metadata block groups that are more than 50 full. The default maximum is 30 which should not degrade performance too much but may be suboptimal if the metadata usage varies wildly over time. The assumption is that underused metadata chunks will get used at some point so it's not absolutelly required to do the reclaim.
- the useful period highly depends on the overall data change pattern on the filesystem
trim
Description: The TRIM operation (aka. discard) can instruct the underlying device to optimize blocks that are not used by the filesystem. This task is performed on-demand by the fstrim utility.
This makes sense for SSD devices or other type of storage that can translate the TRIM action to someting useful (eg. thin-provisioned storage).
Impact when active: Should be low, but depends on the amount of blocks being trimmed.
Tuning:
- the recommended period is weekly, but monthly is also fine
- the trim commands might not have an effect and are up to the device, eg. a block range too small or other constraints that may differ by device type/vendor/firmware
- the default configuration is off because of the the system fstrim.timer
defrag
Description: Run defragmentation on configured directories. This is for convenience and not necessary as defragmentation needs are usually different for various types of data.
Please note that the defragmentation process does not descend to other mount
points and nested subvolumes or snapshots. All nested paths would need to be
enumerated in the respective config variable. The command utilizes find -xdev
, you can use that to verify in advance which paths will the
defragmentation affect.
Special case:
There's a separate defragmentation task that happens automatically and defragments only the RPM database files. This is done via a zypper plugin and the defrag pass triggers at the end of the installation.
This improves reading the RPM databases later, but the installation process fragments the files very quickly so it's not likely to bring a significant speedup here.
Periodic scheduling
There are now two ways how to schedule and run the periodic tasks: cron and systemd timers. Only one can be active on a system and this should be decided at the installation time.
Cron
Cron takes care of periodic execution of the scripts, but they can be run any
time directly from /usr/share/btrfs/maintenance/
, respecting the configured
values in /etc/sysconfig/btrfsmaintenance
.
The changes to configuration file need to be refleced in the /etc/cron
directories where the scripts are linked for the given period.
If the period is changed, the cron symlinks have to be refreshed:
- manually -- use
systemctl restart btrfsmaintenance-refresh
(or thercbtrfsmaintenance-refresh
shortcut) - in yast2 -- sysconfig editor triggers the refresh automatically
- using a file watcher -- if you install
btrfsmaintenance-refresh.path
, this will utilize the file monitor to detect changes and will run the refresh
Systemd timers
There's a set of timer units that run the respective task script. The periods
are configured in the /etc/sysconfig/btrfsmaintenance
file as well. The
timers have to be installed using a similar way as cron.
Quick start
The tasks' periods and other parameters should fit most usecases and do not
need to be touched. Review the mountpoints (variables ending with
_MOUNTPOINTS
) whether you want to run the tasks there or not.
Distro integration
Currently the support for widely used distros is present. More distros can be added. This section describes how the pieces are put together and should give some overview.
Installation
For debian based systems, run dist-install.sh
as root.
For non-debian based systems, check for distro provided package or do manual installation of files as described below.
btrfs-*.sh
task scripts are expected at/usr/share/btrfsmaintenance
sysconfig.btrfsmaintenance
configuration template is put to:/etc/sysconfig/btrfsmaintenance
on SUSE and RedHat based systems or derivatives/etc/default/btrfsmaintenance
on Debian and derivatives/usr/lib/zypp/plugins/commit/btrfs-defrag-plugin.py
post-update script for zypper (the package manager), applies to SUSE-based distros for now- cron refresh scripts are installed (see bellow)
cron jobs
The periodic execution of the tasks is done by the 'cron' service. Symlinks to
the task scripts are located in the respective directories in
/etc/cron.<PERIOD>
.
The script btrfsmaintenance-refresh-cron.sh
will synchronize the symlinks
according to the configuration files. This can be called automatically by a GUI
configuration tool if it's capable of running post-change scripts or services.
In that case there's btrfsmaintenance-refresh.service
systemd service.
This service can also be automatically started upon any modification of the
configuration file in /etc/sysconfig/btrfsmaintenance
by installing the
btrfsmaintenance-refresh.path
systemd watcher.
Post-update defragmentation
The package database files tend to be updated in a random way and get
fragmented, which particularly hurts on btrfs. For rpm-based distros this means files
in /var/lib/rpm
. The script or plugin simpy runs a defragmentation on the affected files.
See btrfs-defrag-plugin.py
for more details.
At the moment the 'zypper' package manager plugin exists. As the package managers differ significantly, there's no single plugin/script to do that.
Settings
The settings are copied to the expected system location from the template
(sysconfig.btrfsmaintenance
). This is a shell script and can be sourced to obtain
values of the variables.
The template contains descriptions of the variables, default and possible values and can be deployed without changes (expecting the root filesystem to be btrfs).
Tuning periodic snapshotting
There are various tools and handwritten scripts to manage periodic snapshots and cleaning. The common problem is tuning the retention policy constrained by the filesystem size and not running out of space.
This section will describe factors that affect that, using snapper as an example, but adapting to other tools should be straightforward.
Intro
Snapper is a tool to manage snapshots of btrfs subvolumes. It can create snapshots of given subvolume manually, periodically or in a pre/post way for a given command. It can be configured to retain existing snapshots according to time-based settings. As the retention policy can be very different for various usecases, we need to be able to find matching settings.
The settings should satisfy user's expectation about storing previous copies of the subvolume but not taking too much space. In an extreme, consuming the whole filesystem space and preventing some operations to finish.
In order to avoid such situations, the snapper settings should be tuned according to the expected usecase and filesystem size.
Sample problem
Default settings of snapper on default root partition size can easily lead to no-space conditions (all TIMELINE values set to 10). Frequent system updates make it happen earlier, but this also affects long-term use.
Factors affecting space consumption
- frequency of snapshotting
- amount of data changes between snapshots (delta)
- snapshot retention settings
- size of the filesystem
Each will be explained below.
The way how the files are changed affects the space consumption. When a new data overwrite existing, the new data will be pinned by the following snapshot, while the original data will belong to previous snapshot. This means that the allocated file blocks are freed after the last snapshot pointing to them is gone.
Tuning
The administrator/user is suppsed to know the approximate use of the partition with snapshots enabled.
The decision criteria for tuning is space consumption and we're optimizing to maximize retention without running out of space.
All the factors are intertwined and we cannot give definite answers but rather describe the tendencies.
Snapshotting frequency
-
automatic: if turned on with the
TIMELINE
config option, the periodic snapshots are taken hourly. The daily/weekly/monthly/yearly periods will keep the first hourly snapshot in the given period. -
at package update: package manager with snapper support will create pre/post snapshots before/after an update happens.
-
manual: the user can create a snapshot manually with
snapper create
, with a given snapshot type (ie. single, pre, post).
Amount of data change
This is a parameter hard to predict and calculate. We work with rough estimates, eg. megabytes, gigabytes etc.
Retention settings
The user is supposed to know possible needs of recovery or examination of previous file copies stored in snapshots.
It's not recommended to keep too old snapshots, eg. monthly or even yearly if there's no apparent need for that. The yearly snapshots should not substitute backups, as they reside on the same partition and cannot be used for recovery.
Filesystem size
Bigger filesystem allows for longer retention, higher frequency updates and amount of data changes.
As an example of a system root partition, the recommended size is 30 GiB, but 50 GiB is selected by the installer if the snapshots are turned on.
For non-system partition it is recommended to watch remaining free space.
Although getting an accurate value on btrfs is tricky, due to shared extents
and snapshots, the output of df
gives a rough idea. Low space, like under a
few gigabytes is more likely to lead to no-space conditions, so it's a good
time to delete old snapshots or review the snapper settings.
Typical usecases
A rolling distro
- frequency of updates: high, multiple times per week
- amount of data changed between updates: high
Suggested values:
TIMELINE_LIMIT_HOURLY="12"
TIMELINE_LIMIT_DAILY="5"
TIMELINE_LIMIT_WEEKLY="2"
TIMELINE_LIMIT_MONTHLY="1"
TIMELINE_LIMIT_YEARLY="0"
The size of root partition should be at least 30GiB, but more is better.
Regular/enterprise distro
- frequency of updates: low, a few times per month
- amount of data changed between updates: low to moderate
Most data changes come probably from the package updates, in the range of hundreds of megabytes per update.
Suggested values:
TIMELINE_LIMIT_HOURLY="12"
TIMELINE_LIMIT_DAILY="7"
TIMELINE_LIMIT_WEEKLY="4"
TIMELINE_LIMIT_MONTHLY="6"
TIMELINE_LIMIT_YEARLY="1"
Big file storage
- frequency of updates: moderate to high
- amount of data changed between updates: no changes in files, new files added, old deleted
Suggested values:
TIMELINE_LIMIT_HOURLY="12"
TIMELINE_LIMIT_DAILY="7"
TIMELINE_LIMIT_WEEKLY="4"
TIMELINE_LIMIT_MONTHLY="6"
TIMELINE_LIMIT_YEARLY="0"
Note, that deleting a big file that has been snapshotted will not free the space until all relevant snapshots are deleted.
Mixed
- frequency of updates: unpredictable
- amount of data changed between updates: unpredictable
Examples:
- home directory with small files (in range of kilobytes to megabytes), large files (hundreds of megabytes to gigabytes).
- git trees, bare and checked out repositories
Not possible to suggest config numbers as it really depends on user expectations. Keeping a few hourly snapshots should not consume too much space and provides a copy of files, eg. to restore after accidental deletion.
Starting point:
TIMELINE_LIMIT_HOURLY="12"
TIMELINE_LIMIT_DAILY="7"
TIMELINE_LIMIT_WEEKLY="1"
TIMELINE_LIMIT_MONTHLY="0"
TIMELINE_LIMIT_YEARLY="0"
Summary
Type | Hourly | Daily | Weekly | Monthly | Yearly |
---|---|---|---|---|---|
Rolling | 12 | 5 | 2 | 1 | 0 |
Regular | 12 | 7 | 4 | 6 | 1 |
Big files | 12 | 7 | 4 | 6 | 0 |
Mixed | 12 | 7 | 1 | 0 | 0 |
About
The goal of this project is to help administering btrfs filesystems. It is not supposed to be distribution specific. Common scripts/configs are preferred but per-distro exceptions will be added when necessary.
License: GPL 2