Udev rules and helper scripts for setting safe disk scterc and drive controller timeout values for mdraid arrays.
When the OS tries to read from or write to the disk, it sends the command and waits. What should happen is that drive returns writes the data successfully.
The proper sequence of events when something goes wrong and the drive can't read the data the OS requests, it should return an error to the OS. In the case of a failed read the raid code then calculates what the data should be from the other disks in the array, and writes it back to the disk which raised an error. Glitches like this are normal and, provided the disk isn't failing, this will correct the problem.
Unfortunately, with commodity desktop drives, they can take over two
minutes to give up, while the linux kernel will, by default, give up
after 30 seconds. At which point, the RAID code recomputes the block
and tries to write it back to the disk. The disk is still trying to
read the data and fails to respond, so the raid code assumes the drive
is dead and kicks it from the array. This is how a single error with
these drives can easily kill an array. With commodity desktop drives,
it is safer therefore to increase the time that the kernel waits for
the disk to return it to allow an error. Empirically it's been found
that 180 seconds is sufficient[1] - all known desktop drives will
eventually return an error within this time. Fortunately, the Linux
kernel allows setting this timeout on a per drive basis via
/sys/block/<device_id>/device/timeout.
The situation becomes more complicated for higher end devices (often intended for use in hardware RAID arrays) which support SCT Error Recovery Control (SCTERC), also called TLER on some drives. This is a configurable pair of settings (one for read and one for write) that set the time that the drive should try to read/write for before returning an error to the OS. In this case it's important to set the both the SCTERC timeouts and kernel controller timeouts appropriately since we don't want the kernel timing out before the disk has timed out.
See [1,2] for further details.
We provide several sets of udev rules here which implement slightly different approaches to the problem.
This is the simplest strategy, and involves making no changes to the SMART settings of the disks.
This strategy first checks to see if the disk contains any RAID partitions of level 1 or higher. If not, no changes are made.
If the disk contains a RAID level 1 or higher parition:
- Use smartctl to see if the disk has any STCERC timeouts set
- If STCERC timeouts are set, no changes are made to the kernel controller timeout.
- If the disk doesn't support STCERC, or STCERC is disabled, then we set the kernel controller timeout to 180 seconds.
Strategies 1 and 2 attempt to actively adjust the STCERC settings as well as set an appropriate kernel controller timeout.
The approach we take is to adjust timeouts for drives containing mdraid managed RAID partitions as follows:
- Discover all partitions on the drive.
- If the drive contains any RAID0 partitions, disable STCERC if present, and set the kernel controller timeout to 180 secs.
- If the drive contains redundant RAID partitions (level 1 or higher) and no
RAID level 0 partitions:
- If the drive does not support STCERC, set the kernel controller timeout to 180 secs.
- If the drive does support STCERC, set the STCERC timeouts to be 5 seconds less than the kernel controller timeout (which is 30 seconds by default)
- If setting the STRCERC timeouts fails, then we disable STCERC and set the kernel controller timeout to 180 secs
The Strategy 1 and 2 implementations use slightly different udev rules for triggering the setting of the timeouts:
Strategy 1: Trigger on creation/change of an mdraid device (e.g. /dev/md0). When that happens, discover the disks that contribute to the array and set the timeouts for each according to the strategy above
Strategy 2: Trigger whenever a partition is created/changed, discover the host drive and set the timeouts according to the strategy above
In both cases the timeouts for a drive can end up being set multiple times until all partitions on the device are known about by the kernel and udev. At this point it's not entirely clear which is the better approach, but the first seems most sensible. In either case, the end result should be the same for any active mdraid devices.
This approach was strongly influenced by some earlier work implementing a udev mechanism for setting the timeouts.
- https://bugs.debian.org/780207
- https://bugs.debian.org/780162
- https://www.smartmontools.org/ticket/658
[1] http://strugglers.net/~andy/blog/2015/11/09/linux-software-raid-and-drive-timeouts/