epoll
A low-level Node.js binding for the Linux epoll API for monitoring multiple file descriptors to see if I/O is possible on any of them.
This module was initially written to detect EPOLLPRI events indicating that urgent data is available for reading. EPOLLPRI events are triggered by interrupt generating GPIO pins. The epoll module is used by onoff to detect such interrupts.
epoll supports Node.js versions 4, 6, 8 and 10.
Installation
Note that epoll can only be installed successfully on Linux systems. Attempting to install epoll on other systems will result in compile errors.
npm install epoll
API
- Epoll(callback) - Constructor. The callback is called when epoll events occur and it gets three arguments (err, fd, events).
- add(fd, events) - Register file descriptor fd for the event types specified by events.
- remove(fd) - Deregister file descriptor fd.
- modify(fd, events) - Change the event types associated with file descriptor fd to those specified by events.
- close() - Deregisters all file descriptors and free resources.
Event Types
- Epoll.EPOLLIN
- Epoll.EPOLLOUT
- Epoll.EPOLLRDHUP
- Epoll.EPOLLPRI
- Epoll.EPOLLERR
- Epoll.EPOLLHUP
- Epoll.EPOLLET
- Epoll.EPOLLONESHOT
Event types can be combined with | when calling add or modify. For example, Epoll.EPOLLPRI | Epoll.EPOLLONESHOT could be passed to add to detect a single GPIO interrupt.
Example - Watching Buttons
The following example shows how epoll can be used to detect interrupts from a momentary push-button connected to GPIO #4 (pin P1-7) on the Raspberry Pi. The source code is available in the example directory and can easily be modified for using a different GPIO on the Pi or a different platform such as the BeagleBone.
The first step is to export GPIO #4 as an interrupt generating input using the export bash script from the examples directory.
./export
export:
#!/bin/sh
echo 4 > /sys/class/gpio/export
sleep 1
echo in > /sys/class/gpio/gpio4/direction
echo both > /sys/class/gpio/gpio4/edge
Then run watch-button to be notified every time the button is pressed and released. If there is no hardware debounce circuit for the push-button, contact bounce issues are very likely to be visible on the console output. watch-button terminates automatically after 30 seconds.
node watch-button
watch-button:
const Epoll = require('epoll').Epoll;
const fs = require('fs');
const valuefd = fs.openSync('/sys/class/gpio/gpio4/value', 'r');
const buffer = Buffer.alloc(1);
// Create a new Epoll. The callback is the interrupt handler.
const poller = new Epoll((err, fd, events) => {
// Read GPIO value file. Reading also clears the interrupt.
fs.readSync(fd, buffer, 0, 1, 0);
console.log(buffer.toString() === '1' ? 'pressed' : 'released');
});
// Read the GPIO value file before watching to
// prevent an initial unauthentic interrupt.
fs.readSync(valuefd, buffer, 0, 1, 0);
// Start watching for interrupts.
poller.add(valuefd, Epoll.EPOLLPRI);
// Stop watching after 30 seconds.
setTimeout(() => {
poller.remove(valuefd).close();
}, 30000);
When watch-button has terminated, GPIO #4 can be unexported using the unexport bash script.
./unexport
unexport:
#!/bin/sh
echo 4 > /sys/class/gpio/unexport
Example - Interrupts Per Second
The following example shows how epoll can be used to determine the number of hardware interrupts that can be handled per second on the Raspberry Pi. The source code is available in the example directory and can easily be modified to use different GPIOs on the Raspberry Pi or a different platform such as the BeagleBone.
In this example, GPIO #7 is wired to one end of a 1kΩ current limiting resistor and GPIO #8 is wired to the other end of the resistor. GPIO #7 is an input and GPIO #8 is an output.
The first step is to export GPIOs #7 and #8 using the export bash script from the examples directory.
./export
export:
#!/bin/sh
echo 7 > /sys/class/gpio/export
echo 8 > /sys/class/gpio/export
sleep 1
echo in > /sys/class/gpio/gpio7/direction
echo both > /sys/class/gpio/gpio7/edge
echo out > /sys/class/gpio/gpio8/direction
Then run interrupts-per-second. interrupts-per-second toggles the state of the output every time it detects an interrupt on the input. Each toggle will trigger the next interrupt. After five seconds, interrupts-per-second prints the number of interrupts it detected per second.
node interrupts-per-second
interrupts-per-second:
const Epoll = require('../../').Epoll;
const fs = require('fs');
const value = Buffer.alloc(1); // The three Buffers here are global
const zero = Buffer.from('0'); // to improve performance.
const one = Buffer.from('1');
const inputfd = fs.openSync('/sys/class/gpio/gpio7/value', 'r+');
const outputfd = fs.openSync('/sys/class/gpio/gpio8/value', 'r+');
let count = 0;
// Create a new Epoll. The callback is the interrupt handler.
const poller = new Epoll((err, fd, events) => {
count += 1;
// Read GPIO value file. Reading also clears the interrupt.
fs.readSync(inputfd, value, 0, 1, 0);
// Toggle GPIO value. This will eventually result
// in the next interrupt being triggered.
const nextValue = value[0] === zero[0] ? one : zero;
fs.writeSync(outputfd, nextValue, 0, nextValue.length, 0);
});
let time = process.hrtime(); // Get start time.
// Start watching for interrupts. This will trigger the first interrupt
// as the value file already has data waiting for a read.
poller.add(inputfd, Epoll.EPOLLPRI);
// Print interrupt rate to console after 5 seconds.
setTimeout(() => {
time = process.hrtime(time); // Get run time.
const rate = Math.floor(count / (time[0] + time[1] / 1E9));
console.log(rate + ' interrupts per second');
// Stop watching.
poller.remove(inputfd).close();
}, 5000);
When interrupts-per-second has terminated, GPIOs #7 and #8 can be unexported using the unexport bash script.
./unexport
unexport:
#!/bin/sh
echo 7 > /sys/class/gpio/unexport
echo 8 > /sys/class/gpio/unexport
Here are some results from the "Interrupts Per Second" example.
Raspberry Pi 3, 1.2Ghz, Raspbian:
node | epoll | kernel | interrupts / sec |
---|---|---|---|
v10.7.0 | v2.0.2 | 4.14.50-v7+ | 22468 |
v8.11.3 | v2.0.2 | 4.14.50-v7+ | 21022 |
v6.14.3 | v2.0.2 | 4.14.50-v7+ | 22745 |
v4.9.1 | v2.0.2 | 4.14.50-v7+ | 21693 |