This has been a labor of love and many curse words. Pandora's Box is an expansion on the Pandora gantry mod for the Voron V0, incorporating a restructured frame and a triple belted bed. This repo is currently undergoing development and a manual is still in the works. I will also have build guides on my YouTube channel if you want to get started before the manual is ready.
| Category | Part Description | Qty | Notes |
|---|---|---|---|
| Filament | Estimates based on the initial release | ||
| Primary Color | 520g | ||
| Accent Color | 420g | ||
| Fasteners | Listed quantities are minimum, buy extra! | ||
| M2x6 BHCS | 20 | ||
| M2x8 SHCS | 30 | ||
| M2 Nut | 30 | ||
| M2x10 Self Tapping Screws for Plastic | 6 | ||
| M3x6 BHCS | 83 | Some may be substituted for M3x8 | |
| M3x8 BHCS | 55 | ||
| M3x10 BHCS | 54 | Some may be substituted for M3x8 | |
| M3x10 SHCS | 1 | ||
| M3x12 BHCS | 14 | ||
| M3x16 BHCS | 18 | ||
| M3x16 SHCS | 2 | ||
| M3x20 BHCS | 2 | ||
| M3x25 BHCS | 12 | ||
| M3x30 BHCS | 10 | ||
| M3x35 BHCS | 5 | ||
| M3x40 BHCS | 6 | ||
| M3x50 BHCS | 2 | ||
| M3 Brass heatstake inserts - short M3x5x4 | 33 | ||
| M3 Nut | 151 | ||
| M3 Lock Nut | 2 | ||
| 3x6x0.5 Shim Washer | 42 | ||
| M5x16 BHCS | 7 | ||
| M5 Nut | 7 | ||
| Frame | |||
| Makerbeam XL 15x15 300mm | 4 | ||
| Makerbeam XL 15x15 200mm | 13 | ||
| Makerbeam XL 15x15 100mm | 3 | ||
| Electronics | |||
| Bigtreetech CB1 | 1 | ||
| Omron Mouse Button - Micro Switch | 2 | ||
| NEMA17 Stepper Motor 45Ncm | 3 | ||
| NEMA14 Stepper Motor 40Ncm | 2 | ||
| MicroSD Card | 1 | ||
| Meanwell LRS-150-24 | 1 | ||
| IEC320 C14 inlet | 1 | ||
| Hotend thermistor | 1 | ||
| Hotend | 1 | ||
| C13 Power Cord | 1 | ||
| Bigtreetech Manta M8P | 1 | ||
| 3M 5952 VHB tape | 1 | ||
| 3010 Blower Fan | 2 | ||
| 3007 axial fan | 1 | ||
| 4010 axial fan | 2 | ||
| 24V Heater Cartridge | 1 | ||
| Cables | |||
| Wire 18gauge 10ft | 1 | ||
| Thermal Fuse 125C | 1 | ||
| Nylon Cable Ties (1.8mm wide or smaller) | 50 | ||
| Microfit3 Dual Row (10circuits) Male & Female Plug | 1 | ||
| JST connectors (2pin 3pin 4pin) | ? | ||
| Insulated Crimp Receptical | 4 | ||
| High Flex Wire 22gauge 100ft | 1 | ||
| High Flex Wire 20gauge 10ft | 1 | ||
| 7mm x 7mm cable chain (less than 1/2 meter needed) | 1 | ||
| WAGO 221-412 (OPTIONAL) | 7 | ||
| Motion | |||
| MGN7H Linear Rail with Carriage - 150mm | 5 | ||
| MGN9(C/H) Linear Rail with Carriage - 200mm | 1 | ||
| GT2 Open Belt (6mm W) - 4000mm | 1 | ||
| GT2 20T (5mm ID 6mm W) | 5 | ||
| F623-RS Bearing | 42 | ||
| GE5C Spherical Bearing | 3 | ||
| 5x30mm Shaft (Length varies by setup) | 1 | ||
| Buildplate | |||
| M4 Knurled Nut | 3 | ||
| Spring Steel Flex Buildplate 120x120mm (OPTIONAL) | 1 | ||
| Silicone DC 24V Heater 100x100mm 60W | 1 | ||
| PEI + 3M 468MP (200MP) | 1 | ||
| MIC6 1/4" Plate - 120x120mm | 1 | ||
| Panels | |||
| Rear Panel - 212x332x3mm | 1 | ||
| Deck Panel 3mm thick (See DXF) | 1 | ||
| Acrylic Sheet Clear - 212x332x3mm | 3 | ||
| Acrylic Sheet Clear - 212x212x3mm | 1 | ||
| Single Sided Foam Tape 1mm Thick (5m) | 1 | ||
| Bowden | |||
| Bowden Tube 4x2mm - 1m | 1 | ||
| Bowden Fitting | 2 | ||
| Misc. | |||
| Rubber Foot (1.5x.75", 38x19mm) | 4 | ||
| Bowden Tube 4x3mm - 1m | 1 | ||
| 6mm x 3mm Round Neodymium Magnets | 13 | ||
| Extruder | |||
| NEMA14 36mm pancake Motor with 10 tooth gear | 1 | ||
| MR85 Bearing | 2 | ||
| Bondtech BMG Extruder Kit | 1 |