CyphalRobotController07/CAN
Main controller board for the T07 robot platform and similar robots with a Raspberry Pi Pico to connect via CAN using OpenCyphal and UCANPHY Micro
- power supply for the whole system
- 5 V for the cyphal network and embedded board (Raspberry Pi or Beagle Bone Black)
- switchable output of battery voltage to supply additional hardware
- switchable output of battery voltage to supply LED or head lamp
- Input voltage up to 25 V
- Blade type fuse (ATO fuse)
- Power Pole connector
- measurement of input voltage and current with TI INA226
- control 2 DC motors
- 2 quad encoders for motors
- emergency stop
- Infineon IFX007T drivers, up to 40V and 55A
3 ultra sonic sensors HC-SR04 (not implemented yet)
- I2C bus
- qwiic connector
- 9 axis IMU Bosch BNO055 via I2C
- back-EMF measurement with ADS1015
- EEPROM 24LC64
- serial port for optional GNSS
- Neopixel for status
- CAN with Cyphal support
Pin |
Pin Name |
Signal |
Direction |
Description |
1 |
GP0 |
UART0_TX |
output |
reserved for future use (GNSS) |
2 |
GP1 |
UART0_RX |
input |
reserved for future use (GNSS) |
3 |
GND |
GND |
GND |
|
4 |
GP2 |
QUAD0 |
input |
Quad encoder A channel 0 |
5 |
GP3 |
QUAD1 |
input |
Quad encoder A channel 1 |
6 |
GP4 |
I2C0_SDA |
bidir |
for eeprom and qwiic connector |
7 |
GP5 |
I2C0_SCL |
output |
for eeprom and qwiic connector |
8 |
GND |
GND |
GND |
|
9 |
GP6 |
PWM4 |
output |
motor pwm output 4 |
10 |
GP7 |
PWM3 |
output |
motor pwm output 3 |
11 |
GP8 |
PWM2 |
output |
motor pwm output 2 |
12 |
GP9 |
PWM1 |
output |
motor pwm output 1 |
13 |
GND |
GND |
GND |
|
14 |
GP10 |
INH34 |
output |
motor inhibit output 3 and 4 |
15 |
GP11 |
INH12 |
output |
motor inhibit output 1 and 2 |
16 |
GP12 |
EM_STOP |
input |
emergency stop |
17 |
GP13 |
NEOPIXEL |
output |
Neopixel |
18 |
GND |
GND |
GND |
|
19 |
GP14 |
QUAD2 |
input |
Quad encoder B channel 0 |
20 |
GP15 |
QUAD3 |
input |
Quad encoder B channel 1 |
21 |
GP16 |
SPI_MISO |
input |
SPI for MCP2515 |
22 |
GP17 |
MCP2515_CS |
output |
SPI for MCP2515 |
23 |
GND |
GND |
GND |
|
24 |
GP18 |
SPI_CLK |
output |
SPI for MCP2515 |
25 |
GP19 |
SPI_MOSI |
output |
SPI for MCP2515 |
26 |
GP20 |
MCP2515_INT |
input |
interrupt for MCP2515 |
27 |
GP21 |
OUTPUT0 |
output |
power output 0 |
28 |
GND |
GND |
GND |
|
29 |
GP22 |
OUTPUT1 |
output |
power output 1 |
30 |
RUN |
RESET |
input |
Reset for Board |
31 |
GP26 |
ANALOG_INPUT0 |
analog input |
analog input 0 |
32 |
GP27 |
ANALOG_INPUT1 |
analog input |
analog input 1 |
33 |
GND |
GND |
GND |
|
34 |
GP28 |
ANALOG_INPUT2 |
analog input |
analog input 2 |
35 |
ADC_VREF |
|
analog |
|
36 |
3V3 (OUT) |
3V3-rail |
power |
supply voltage for board |
37 |
3V3_EN |
|
input |
|
38 |
GND |
GND |
GND |
|
39 |
VSYS |
|
power |
|
40 |
VBUS |
5V-rail |
power |
supply voltage for board |
address |
device |
description |
0x40 |
INA226 |
voltage and current measurement |
0x48 |
ADS1015 |
motor measurement |
0x4A |
BNO055 |
IMU |
0x50 |
24LC64 |
eeprom for storage of settings |