A tool to capture packets from WLAN devices and to discover potential weak points within own WiFi networks by running layer 2 attacks against the WPA protocol.
Designed to to run (mostly headless) on small systems like a Raspberry Pi Zero.
-
An overview of Hashcat mode 22000. - Hashcat Wiki
-
A set of tools by ZerBea intended for processing capture files. - hcxtools Repository
-
Old but still applicable write-up by atom of the Hashcat forums covering a new attack on WPA/WPA2 using PMKID. - Hashcat Forum Thread
-
Hashcat mode 22000 write-up by atom of the Hashcat forums. - Hashcat Forum Thread
-
A write-up by Ido Hoorvitch from CyberArk covering the statistics of WPA/WPA2 password cracking. - CyberArk Article
-
A section of this README that covers hcxdumptool's abilities and the responsibilities of using it. - Warning!
-
It does not crack WPA PSK related hashes. (Use Hashcat or JtR to recover the PSK.)
-
It does not crack WEP. (Use the aircrack-ng suite instead.)
-
It does not crack WPS. (Use Reaver or Bully instead.)
-
It does not decrypt encrypted traffic. (Use tshark or Wireshark in parallel.)
-
It does not record all traffic captured on the WLAN device. (Use tshark or Wireshark in parallel.)
-
It does not perform Evil Twin attacks.
-
It does not provide a beautiful status display.
-
It is not a honey pot.
Unsupported: Windows OS, macOS, Android, emulators or wrappers!
| Tool | Description |
|---|---|
| hcxdumptool | Tool to run several tests against WPA PSK to determine if ACCESS POINTs or CLIENTs are vulnerable. |
| hcxpcapngtool | Tool to convert raw PCAPNG files to Hashcat and JtR readable formats. (hcxtools) |
| hcxhashtool | Tool to filter hashes from HC22000 files based on user input. (hcxtools) |
| hcxpsktool | Tool to get weak PSK candidates from HC22000 files. (hcxtools) |
| hcxeiutool | Tool to calculate wordlists based off ESSIDs gathered. (hcxtools) |
| Hashcat/JtR | Third party tools used to infer PSK from HC22000 hash files. |
hcxdumptool -> hcxpcapngtool -> hcxhashtool (additional hcxpsktool/hcxeiutool) -> Hashcat or JtR
- Knowledge of radio technology.
- Knowledge of electromagnetic-wave engineering.
- Detailed knowledge of 802.11 protocol.
- Detailed knowledge of key derivation functions.
- Detailed knowledge of Linux.
- Detailed knowledge of filter procedures. (Berkeley Packet Filter, capture filter, display filter, etc.)
- Operating system: Linux (recommended: kernel >= 6.6, mandatory: kernel >= 5.15)
- Recommended: Arch Linux (notebooks and desktop systems), OpenWRT (small systems like Raspberry Pi, WiFi router)
- WLAN device chipset must be able to run in monitor mode. MediaTek chipsets are preferred due to active monitor mode capabilities.
- WLAN device driver must support monitor and full frame injection mode.
- gcc >= 13 recommended (deprecated versions are not supported: https://gcc.gnu.org/)
- make
- libpcap and libpcap-dev (If internal BPF compiler has been enabled.)
- Raspberry Pi A, B, A+, B+, Zero (WH). (Recommended: Zero (WH) or A+, because of a very low power consumption), but notebooks and desktops will work as well.
- GPIO hardware mod recommended (push button and LED) on Raspberry Pi
- To allow 5/6/7GHz packet injection, it is mandatory to uncomment a regulatory domain that support this: /etc/conf.d/wireless-regdom
On most distributions, hcxdumptool and hcxtools are available through the package manager.
If you decide to compile latest git head, make sure that your distribution is updated to it's latest version and make sure that all header files and dependencies have been installed!
Notice: The packages mentioned in the "Requirements" section sometimes come under different names in a package manager! Make sure to install the correct packages!
git clone https://github.com/ZerBea/hcxdumptool.git
cd hcxdumptool
make -j $(nproc)
Install to /usr/bin:
make install (as super user)
Or install to /usr/local/bin:
make install PREFIX=/usr/local (as super user)
On headless operation, remove -DSTATUSOUT from the Makefile before compiling! That way, the status display will not be compiled. This will save CPU cycles and prevent ERRORs from occurring.
It is theoretically possible to compile hcxdumptool for other systems (e.g. Android) and other distributions (e.g. KALI) and other operating systems (BSD) as well, but there is no support and feature requests will be rejected.
-
Do not expect flawless drivers on brand new hardware!
-
Driver must support monitor mode and full packet injection!
-
No support for prism devices!
-
WIRELESS EXTENSIONS are deprecated and not longer supported!
Get information about VENDOR, model, chipset, and driver here: https://wikidevi.wi-cat.ru/
Manufacturers do change chipsets without changing model numbers. Sometimes they add (v)ersion or (rev)vision.
Preferred chipsets come from MediaTek due to active monitor mode being very reliable. (Important notice: Massive problems with MT76 USB 3.0 devices if connected to some USB 3.0 ports!)
Some device and driver tests are here: ZerBea#361
Always verify the actual chipset with 'lsusb' and/or 'lspci'!
No support for a third party driver which is not part of the official Linux kernel (https://www.kernel.org/) Report related issues to the site, from which you downloaded the driver.
No support for a driver which doesn't support monitor mode and full frame injection natively. If you need these features, do a request on www.kernel.org
Recommended WiFi chipsets:
-
MediaTek (mt76)
-
Realtek (rtl8xxxu)
-
Ralink (rt2800usb)
Not recommended WiFi chipsets:
-
Broadcom (Neither monitor mode nor frame injection by official Linux kernel.)
-
Qualcomm (No frame injection by official Linux kernel.)
-
Intel (Monitor mode and frame injection problems.)
More information about possible issues or limitations:
https://wireless.wiki.kernel.org/en/users/Drivers/ath10k
The best high frequency amplifier is a good antenna!
It is much better to achieve gain using a good antenna instead of increasing transmission power.
| VENDOR MODEL | TYPE |
|---|---|
| LOGILINK WL0097 | Grid Parabolic |
| TP-LINK TL-ANT2414 A/B | Panel |
| LevelOne WAN-1112 | Panel |
| DELOCK 88806 | Panel |
| TP-LINK TL-ANT2409 A | Panel |
| VENDOR MODEL | TYPE |
|---|---|
| NAVILOCK NL-701US | USB |
| JENTRO BT-GPS-8 activepilot | BLUETOOTH |
| Script | Description |
|---|---|
| stopnm | Example script to start NetworkManager |
| startnm | Example script to stop NetworkManager |
| startnlmon | Example script to activate NETLINK monitor |
When using this hardware modification, the LED will flash every 10 seconds if everything is fine and signals are received correctly.
To terminate manually, press the push button for at least 10 seconds until LED turns on. (The LED will also turn on if hcxdumptool terminates.)
Afterwards, the Raspberry Pi can be turned off and disconnected from it's power supply.
ENTERPRISE NUMBER: 0x2a, 0xce, 0x46, 0xa1
MAGIC NUMBER: 0x2a, 0xce, 0x46, 0xa1, 0x79, 0xa0, 0x72, 0x33, 0x83, 0x37, 0x27, 0xab, 0x59, 0x33, 0xb3, 0x62, 0x45, 0x37, 0x11, 0x47, 0xa7, 0xcf, 0x32, 0x7f, 0x8d, 0x69, 0x80, 0xc0, 0x89, 0x5e, 0x5e, 0x98
OPTIONCODE_MACMYORIG: 0xf29a (6 byte)
OPTIONCODE_MACMYAP: 0xf29b (6 byte)
OPTIONCODE_RC: 0xf29c (8 byte)
OPTIONCODE_ANONCE: 0xf29d (32 byte)
OPTIONCODE_MACMYSTA: 0xf29e (6 byte)
OPTIONCODE_SNONCE: 0xf29f (32 byte)
OPTIONCODE_WEAKCANDIDATE: 0xf2a0 (64 byte) == 63 characters + zero
OPTIONCODE_GPS: 0xf2a1 (max 128 byte)
You might expect me to recommend that everyone should be using hcxdumptool/hcxtools. But the fact of the matter is, hcxdumptool/hcxtools is NOT recommended to be used by inexperienced users or newbies.
If you are not familiar with Linux in general or you do not have at least a basic level of knowledge as mentioned in the "Requirements" section, hcxdumptool/hcxtools is probably not what you are looking for. However, if you have that knowledge hcxdumptool/hcxtools can do magic for you.
Misuse of hcxdumptool within a network, particularly without authorization, may cause irreparable damage and result in significant consequences. “Not understanding what you were doing” is not going to work as an excuse.
The entire toolkit (hcxdumptool and hcxtools) is designed to be an analysis toolkit.
It should only be used in a 100% controlled environment!
If you can't control the environment it is absolutely mandatory to set the BPF!
The BPF can be used to select a target (or multible targets) or to protect devices.
By default options hcxdumptool is running three attack vectors:
-
connect to an ACCESS POINT to get a PMKID (turn off by --attemptapmax)
-
disconnect a CLIENT from an associated ACCESS POINT to get a complete handshake (M1M2M3M4) and a PMKID (turn off by --attemptapmax)
-
allow a CLIENT to connect to hcxdumptool to get a challenge (M1M2) or an EAP-ID (turn off by --attemptclientmax)
You must use hcxdumptool only on networks you have permission to do this and if you know what you are doing, because:
-
hcxdumptool is able to prevent complete WLAN traffic transmission. (Depending on selected options.)
-
hcxdumptool is able to capture PMKIDs from access points. (Only one single PMKID from an access point is required. Use hcxpcapngtool to convert them to a format Hashcat or JtR understands.)
-
hcxdumptool is able to capture handshakes from non-connected clients. (Only one single M2 from the client is required. Use hcxpcapngtool to convert them to a format Hashcat or JtR understands.)
-
hcxdumptool is able to capture handshakes from 5/6GHz clients on 2.4GHz. (Only one single M2 from the client is required. Use hcxpcapngtool to to a format Hashcat or JtR understands.)
-
hcxdumptool is able to capture passwords from the WLAN traffic. (Use hcxpcapngtool -R to save them to file, or together with networknames [-E].)
-
hcxdumptool is able to request and capture extended EAPOL (RADIUS, GSM-SIM, WPS. hcxpcapngtool will show you information about them.)
-
hcxdumptool is able to capture identities from the WLAN traffic. (Example: Request IMSI numbers from mobile phones - use hcxpcapngtool -I to save them to file.)
-
hcxdumptool is able to capture usernames from the WLAN traffic. (Example: User name of a server authentication - use hcxpcapngtool -U to save them to file.)
-
Do not use a logical interface and leave the physical interface in managed mode!
-
Do not use hcxdumptool in combination with the aircrack-ng suite, Reaver, Bully or other tools which take access to the interface!
-
Stop all services which take access to the physical interface! (NetworkManager, wpa_supplicant,...)
-
Do not use tools like macchanger as they are useless since hcxdumptool uses its own random MAC address space.
-
Do not merge PCAPNG dumpfiles because that will destroy custom block hash assignments!
-
Capture format PCAPNG is compatible with Wireshark and tshark.
-
PCAPNG Format Information - https://pcapng.com/
-
The Linux Kernel Documentation - https://www.kernel.org/doc/html/latest/
-
BPF Documentation - https://www.kernel.org/doc/html/latest/bpf/index.html
-
Linux Commands Handbook - https://www.freecodecamp.org/news/the-linux-commands-handbook/
-
WPA2 Information - https://en.wikipedia.org/wiki/Wpa2
-
802.11 Frame Types - https://en.wikipedia.org/wiki/802.11_Frame_Types
-
802.11 Security Improvements - https://en.wikipedia.org/wiki/IEEE_802.11i-2004