ply-bbb

This repo builds an eBPF-friendly Linux kernel and the ply dynamic tracing tool for BeagleBone SBCs. It was meant to accompany the presentation on "ply: lighweight eBPF tracing" that I gave at the Embedded Linux Conference on September 28, 2021. Watch the YouTube video recording or download the slides for details on how this Linux kernel and rootfs were configured.

Getting started

Start by cloning the repo and its Buildroot submodule:

$ git clone --recursive https://github.com/fvasquez/ply-bbb.git

Install all the necessary Buildroot dependencies:

$ sudo apt install sed make binutils build-essential gcc g++ bash patch gzip bzip2 perl tar cpio unzip rsync file bc wget

The preceding packages were required to build on Ubuntu 20.04 LTS.

Optionally, to reconfigure the Linux kernel or root filesystem for the target, install libncurses-dev as well:

$ sudo apt install libncurses-dev

Now configure the image and build it:

$ cd ply-bbb
$ make all

The build will take several minutes to complete the first time you run it. When the image is done building look for the following file:

$ ls output/images/sdcard.img

This is the bootable image to write to a micoSD card for deployment to a BeagleBone.

Deploying

To deploy the finished image to a BeagleBone Black and boot it:

Use balena Etcher to write ply-bbb/output/images/sdcard.img out to a microSD card.
Insert the microSD card into a BeagleBone Black.
Plug the USB end of a 3-pin FTDI cable into your computer.
Connect the black (GND), orange (TX) and yellow (RX) wires from a 3-pin FTDI cable to pins 1, 4 and 5 on the BeagleBone Black.
$ sudo screen /dev/ttyUSB0 115200
Apply power to the BeagleBone Black while holding down the BOOT button (nearest to the microSD slot).
Log in from the serial console as root with a password of temppwd.

A serial console is only needed to find the IP address of the BeagleBone Black. SSH offers a better command line and terminal output experience. Alternatively, use arp-scan to locate the BeagleBone's IP address if you do not have a USB to serial cable handy.

Connecting

To SSH into a BeagleBone Black running the deployed image:

Plug an Ethernet cable from your router or computer into the BeagleBone Black.
Wait a few seconds for the BeagleBone Black to obtain a dynamic or link-local IP address.
Run ifconfig from the serial console or arp-scan from your computer to view the BeagleBone Black's IP address on eth0.
$ ssh root@<IP address>
Enter temppwd when prompted for a password.

Upon connecting, you will find yourself in a $HOME directory of /root. There are several ply scripts installed in this directory to experiment with.

Examples

The following ply examples were all run on a BeagleBone Black with the preceding sdcard.img deployed. Notice that the image comes with Redis installed so that we have a daemon to play with.

Count vfs calls by executable and function:

# ply -c \
>     "dd if=/dev/zero of=/dev/null bs=1 count=100" \
>     'kprobe:vfs_* { @[comm, caller] = count(); }'
ply: active
100+0 records in
100+0 records out
ply: deactivating

@:
{ dd             , vfs_statx }: 1
{ dd             , vfs_fstat }: 1
{ dd             , vfs_readlink }: 1
{ sh             , vfs_read }: 1
{ sh             , vfs_fstat }: 1
{ sh             , vfs_readlink }: 1
{ dd             , vfs_getattr_nosec }: 2
{ dd             , vfs_open }: 3
{ ply            , vfs_write }: 3
{ sh             , vfs_open }: 3
{ sh             , vfs_statx }: 4
{ sh             , vfs_getattr_nosec }: 5
{ dropbear       , vfs_read }: 9
{ dropbear       , vfs_writev }: 9
{ ply            , vfs_read }: 19
{ ply            , vfs_open }: 25
{ dd             , vfs_read }: 101
{ dd             , vfs_write }: 108

Count syscalls systemwide by function:

# ply 'k:__se_sys_* { @syscalls[caller] = count(); }'
ply: active
^Cply: deactivating

@syscalls:
{ __se_sys_write }: 2
{ __se_sys_writev }: 2
{ sys_select }: 2
{ __se_sys_bpf }: 4
{ __se_sys_rt_sigaction }: 6
{ __se_sys_close }: 160
{ __se_sys_epoll_wait }: 160
{ __se_sys_perf_event_open }: 169
{ __se_sys_read }: 304
{ sys_brk }: 362
{ sys_ioctl }: 482
{ sys_clock_gettime32 }: 486
{ __se_sys_open }: 653
{ __se_sys_gettimeofday }: 1431

Print stack trace on entry to i2c-transfer:

# ./i2c-stack.ply

	i2c_transfer
	regmap_i2c_write+28
	_regmap_raw_write_impl+1656
	_regmap_bus_raw_write+128
	regmap_write+68
	tps65217_set_bits+104
	tps65217_pmic_set_voltage_sel+116
	_regulator_call_set_voltage_sel+108
	_regulator_do_set_voltage+1156
	regulator_set_voltage_rdev+152
	regulator_do_balance_voltage+824
	regulator_set_voltage_unlocked+220
	regulator_set_voltage+76
	_set_opp_voltage+56
	dev_pm_opp_set_rate+748
	__cpufreq_driver_target+420
	od_dbs_update+316
	dbs_work_handler+48
	process_one_work+500
	worker_thread+80
	kthread+312
	ret_from_fork+20

Read size distribution:

# ./read-dist.ply
ply: active
^Cply: deactivating

@:
{ retsize }:
	[   8,   15]	       2 ┤▍                               │
	[  16,   31]	       1 ┤▏                               │
	...
	[ 128,  255]	     172 ┤███████████████████████████████▌│

See short-lived processes:

# ./execsnoop.ply &
# ply: active

# /etc/init.d/S50redis stop
(   0) /etc/init.d/S50redis                              0
Stopping redis: (   0) /usr/bin/redis-cli                                0
OK
# /etc/init.d/S50redis start
(   0) /etc/init.d/S50redis                              0
Starting redis: (   0) /sbin/start-stop-daemon                           0
OK
# (1002) /usr/bin/redis-server                             0

# /etc/init.d/S50redis stop
(   0) /etc/init.d/S50redis                              0
Stopping redis: (   0) /usr/bin/redis-cli                                0
OK
# /etc/init.d/S50redis start
(   0) /etc/init.d/S50redis                              0
Starting redis: (   0) /sbin/start-stop-daemon                           0
OK
# (1002) /usr/bin/redis-server                             0

# fg %1
./execsnoop.ply
^Cply: deactivating

execs:
{   270 }: /etc/init.d/S50redis
{   272 }: /etc/init.d/S50redis
{   279 }: /etc/init.d/S50redis
{   281 }: /etc/init.d/S50redis
{   273 }: /sbin/start-stop-daemon
{   282 }: /sbin/start-stop-daemon
{   271 }: /usr/bin/redis-cli
{   280 }: /usr/bin/redis-cli
{   275 }: /usr/bin/redis-server
{   284 }: /usr/bin/redis-server

Count TCP I/O by executable and direction:

# ./tcp-send-recv.ply &
# ply: active

# redis-cli --latency
min: 0, max: 5, avg: 1.20 (1025 samples)^C
# fg %1
./tcp-send-recv.ply
^Cply: deactivating

@:
{ dropbear       , recv    }: 32
{ redis-cli      , recv    }: 1025
{ redis-cli      , send    }: 1025
{ redis-server   , send    }: 1025
{ redis-server   , recv    }: 1026
{ dropbear       , send    }: 1041

Run LRU simulation using 100k keys and display heap allocation distribution:

# redis-cli flushall
OK
# ./heap-allocs.ply &
# ply: active

# redis-cli --lru-test 100000
7000 Gets/sec | Hits: 880 (12.57%) | Misses: 6120 (87.43%)
7000 Gets/sec | Hits: 2242 (32.03%) | Misses: 4758 (67.97%)
7000 Gets/sec | Hits: 3260 (46.57%) | Misses: 3740 (53.43%)
6750 Gets/sec | Hits: 3797 (56.25%) | Misses: 2953 (43.75%)
7000 Gets/sec | Hits: 4441 (63.44%) | Misses: 2559 (36.56%)
7000 Gets/sec | Hits: 4826 (68.94%) | Misses: 2174 (31.06%)
7000 Gets/sec | Hits: 5154 (73.63%) | Misses: 1846 (26.37%)
7000 Gets/sec | Hits: 5426 (77.51%) | Misses: 1574 (22.49%)
7000 Gets/sec | Hits: 5583 (79.76%) | Misses: 1417 (20.24%)
^C
# fg %1
./heap-allocs.ply
^Cply: deactivating

@:
{ alloc size      }:
	[   0,    1]	       1 ┤                                │
	...
	[  4k,   8k)	    1073 ┤███████████████████▊            │
	[  8k,  16k)	     593 ┤██████████▉                     │
	[ 16k,  32k)	      64 ┤█▏                              │
	[ 32k,  64k)	       2 ┤                                │
	[ 64k, 128k)	       1 ┤                                │
	[128k, 256k)	       1 ┤                                │
	...
	[  4M,   8M)	       3 ┤                                │

heaps:
{ heap-allocs.ply,   424 }: 4841472
{ redis-server   ,   270 }: 8679424
{ redis-cli      ,   425 }: 14528512

fvasquez / ply-bbb

ply-bbb

Getting started

Deploying

Connecting

Examples

About

Languages