ESP8266 port of Opensprikler software. NOTE: This code and the documentation is WORK IN PROGRES. All your comments and suggestions are welcome (please use GitHub Issue form).
Last June release should be last beta release: I will do some other months of testing but new corrections or improvements are not forseen. But since I have worked with OpenSprinkler I have considered the UI to be the weekest aspect of this project and I intend to create a new branch to revise and upgrade all User Interfaces, so that most of the operations can be controlled and monitored locally .
JUNE 2016 V 2 2.1.6 Second ESP 8266 Beta release
Last relase include several improvements and additions:
-WiFimanagger library to select right SSID and define password in a wireless manner.
-Arduino OTA library library to upload firmware without using USB.
-correction of serveral bugs
-testing of new hardware configurations:a Wiki with description of all Hw devices tested and relative pros/contras will be added to Git, you are invited to add your own projet and experience to it.
OpenSprinkler_Arduino V2.1.6 - beta test / based on the unified firmware at https://github.com/OpenSprinkler/OpenSprinkler-Firmware
While this release works OK, PLEASE see the 'Notes' section below for some known issues
Hostname definition now you can access it with http://OSxx.local your Opensprinkler station xx is a unique n. from ESP hw n. EEPROM on internalFlash now an external I2c cip is not required any more: up to 4kbytes can be store on flash correction of bugs ScanI2c()-scanning of i2c peripherals
Implemented Proto3 hardware configuration using both PCF8574 and 75SN575 IC .
BUGS COORECTION:
-corrected PIN definition on shift register control code
-corrected bug in log files I/O preventing historical log data extraction
-corrected pin definitions (is now in term of GPIO n. )
-enabled lcd brigthness control
-source code:
all sources & libraries are in the same directory OPENSPRINKER_Arduino_V_2_1_6
main renamed OpenSprinkler_ESP8266_v_2_1_6
OpenSprinkler-Arduino is a branch from Ray's OpenSprinkler code found in:
https://github.com/OpenSprinkler/OpenSprinkler-Firmware
Scope of these modification is to increase the HW components compatible with OpenSprinkler: starting with a beta version ported to ESP8266.
This code is a modified starting from Opensprinkler-Arduino code : the OPENSPRINKLER code modified by Dave for Arduino MEGA porting , found in :
https://github.com/Dave1001/OpenSprinkler-Arduino
In general the approach is to make the minimum changes necessary to use standard Arduino libraries, and to get alternative hardware to run, and to debug.
Changes from Rays original code are marked with OPENSPRINKLER_ARDUINO (or variations thereof)and changes for ESP8266 porting are bounded by "#ifdef ESP8266" , "#endif" commands.
Refer to the start of 'Config.h' and 'Pins.h' for options to substitute different hardware and turn functions on or off.
FULL CREDIT to Ray for all the hard work to build and maintain the Open Sprinkler project and to Dave for his porting to Mega that have simplified a lot my conversion to ESP8266.
Version: Opensprinkler V2.1.6 / beta_ESP_01
Date: March 2016
Repository: https://github.com/pbecchi/OpenESP8266_Sprinkler
License: Creative Commons Attribution-ShareAlike 3.0 license
This Code is made to be compatible with several MCU and several peripheral:
-the code has been ported to ESP8266 but compatibility with previous MCU & peripheral has been maintained
-the list of peripheral that should be compatible is the following:
-MCU
ESP8266 boards: better to use ESP8266 12E or NODEMCU v1.0 with more GPIO available.
With NodeMCU you don’t have to worry about power supply and USB interface.
-LCD
Parallel 16x2 and 20x4 LCD
Freetronics LCD Shield 16x2 + 5 buttons
I2C 16x2 or 20x4 LCD
on 20x4 2 additional lines and characters to be used for future developments
-RTC DS1307 or DS3231(best choice for ESP8266) + AT24C32 I2C EEPROM as can be found on z-042 breakout boards.
The presence of the I2C EEPROM is necessary for the actual (beta_ESP_01) code to work on ESP8266.
-ETHERNET
-use of ESP8266 internal capability (code has been added to manage Wi-Fi connections to Hub)
-W5100 Ethernet shield (from Dave1001 code)
-ENC28J60 (from original OS code)
-SD CARD
-at the moment (current release), on ESP8266, I have added a tested emulation of SD drive on FLASH memory (ESP8266 SPIFFS)
-SD SPI drive should be compatible (having sufficient GPIO available on ESP8266)
-PIN INPUT/OUTPUT
Since on ESP8266 only very few GPIO can be utilized, are bound to that number or
-use PCF8574 (5) expansion IC with 8/16 additional IO pins (this is the preferred solution)
-pin using interrupts should be routed directly to ESP8266
-PIN BUTTON
-analog input (5 inputs on Dave code Freetronic shield, 4 in my case using 4 switches).
-standard 3 BUTTON PIN input with or without use of PCF8574
-PIN for STATIONS output
-shift register expander (like 75SN595) driven by 3 GPIO or thought an PCF8574
-parallel connection to MCU (only for MEGA board) (from Dave1001 code)
!!!!a serial connection (USB) is necessary to upload and debug the code and for FIRST TIME CODE STARTUP (selection of WiFi network enter password etc…..)
!!!!!IMPORTANT: ESP8266 is only compatible with 3.3V logic levels!!!!!! (Use level shifters where necessary)
Schematics of prototype boards I have built to test the code and some components data sheet are in the HARDWARE directory. You can use any combination of GPIO pin you would like as far as you use components supported by the code (libraries) and you change the pins.h file accordingly (detail instructions follows)
I intend to test as many different configurations as possible: participation to this effort is welcome! You could describe your HW configuration as well as functions of your prototype and give me input for code update.....thanks!
In addition you'll need:
-
Any 5V relay card that can be driven from Arduino digital output pins or a simple Triac gate circuit (see Hw schematics)
-
Power supplies(s), bits & pieces to hook it all up
To install and compile this code you need:
-
Arduino IDE 1.6.5+ -> http://arduino.cc/ Using ESP core support library from http://arduino.esp8266.com/versions/1.6.5-1160-gef26c5f/doc/reference.html The code is large and may be difficult to manage with the limited resources of Arduino IDE
My suggestion: use Visual Studio 2015 plus the Visual Micro add-on from here -> http://www.visualmicro.com/ If you use Arduino Ide put all file in the same directory and get rid of "../" on includes!
-
Libraries:
Most of the libraries are included on the GitHub code and should be placed on the same directory on the code.
Following libraries should be on the sketchbook/libraries folder:
-"Time.h" http://www.pjrc.com/teensy/td_libs_Time.html
-"TimeAlarms.h" http://www.pjrc.com/teensy/td_libs_TimeAlarms.html
-"DS1307RTC.h" http://www.pjrc.com/teensy/td_libs_DS1307RTC.html
-"LiquidCrystalI2C.h https://bitbucket.org/fmalpartida/new-l ... V1.2.1.zip
-"Time.h" https://github.com/PaulStoffregen/Time
-"DS1307RTC.h" https://github.com/PaulStoffregen/DS1307RTC -
Other libraries are standard (part of Arduino ESP core/Arduino IDE):
Additional libraries for different Hw configurations
- "LiquidCrystal.h" Standard Arduino Library
- "SPI.h" Standard Arduino Library
- "Ethernet.h" Standard Arduino Library
- "EthernetUdp.h" Standard Arduino Library
- "SDFat.h" https://github.com/greiman/SdFat
ESP8266 not compatible libraries:
- "ICMPPing.h" https://github.com/BlakeFoster/Arduino-Ping
- "MemoryFree.h" http://playground.arduino.cc/Code/AvailableMemory
NOTE - unless you're careful, you may have some issues with the libraries above co-existing with OpenSprinklerGen library. The easiest way to fix it is to remove OpenSprinkler from your Arduino library folder.
Assuming you have the libraries above installed, the code here *should* compile without too many issues (good luck!)
If you're trying to make it work:
-
Library conflicts:
- if you're not careful you'll get a whole bunch (kind of like .dll hell from Windows in the old days before .net)
- I STRONGLY recommend:
- get rid of any Opensprinkler code you may have in your Arduino 'library' folder
- update your Arduino libraries to the latest from link above
-
Multiple Simultaneous Button Presses: -Work only with digital buttons
If you're a developer:
-
Software IDE
- I'm using Visual Studio 2015 Community Edition plus Visual Micro to build and upload code.
- this release was tested to compile and upload using Arduino IDE Version 1.6.5
-
Discrete Outputs :
- the number of discrete pins is pre-defined as 16 maximum - you'll need to edit OpenSprinklerGen2.cpp and defines.h if you want more - Hostname
- hostname isn't implemented for opensprinkler : (I am working on it: next commit!)
-Your HW configuration:
-editing Pins.h file it will be possible to select a different hardware configuration that suit your needs:
Actually I have made to different prototype and you will see how the code address both.
-other file that can be changed (carefully) are : config.h and defines.h ( for DEBUG and other code modifications).
-How to change Pins.h file
The file details each pin used for your HW configuration.
You have first to define the configuration you are working on (ESP or other MCU)
and the type of peripheral you are using:see detailed comment in the file about it.
Then you have to select the pins (for I2c, station output, shift registers, rain ....all other functions)
and assign it to a pin number, using following rule:
-pin <32 will be assigned to MCU (ESP8266) GPIO pin numbers( only few are available for ESP8266).
-pin >32 and <48 will be assigned to an first I2c extender (the one with the lowest address)
-pin >48 and <64 will be assigned to second I2c extender
-so on 16 pin at the time
This way you can use expander for all functions (interrupt donot work right now) and free most of the pins on MCU
-First Code Startup
When you start the code the program will check your connected i2c devices and define what to do with it:
check on Serial output to verify that your HW has been setup correctely.
It will also check available WiFi networks and ask relative Password than will be stored in a file for future restart.
For first startup then a USB connection is required to verify I2c and entering passwords!
All other restart dont need any intervention.
TO DO
Progress with DEBUGGING and with documentation: your help and suggestion is highly appreciated!