hcxtools

Small set of tools to capture and convert packets from wlan devices for the use with latest hashcat. The tools are 100% compatible to hashcat and recommended by hashcat. This branch is pretty closely synced to hashcat git branch (that means: latest hcxtools matching on latest hashcat beta). Support for hashcat hash-modes (2500, 2501, 4800, 5500, 12000). After capturing, upload the "uncleaned" cap here (http://wpa-sec.stanev.org/?submit) to see if your ap or the client is vulnerable by using common wordlists. Convert the cap to hccapx and check if wlan-key or plainmasterkey was transmitted unencrypted.

Brief description

Multiple stand-alone binaries - designed to run on Raspberry Pi's.

All of these utils are designed to execute only one specific function.

Read this post: hcxtools - solution for capturing wlan traffic and conversion to hashcat formats (https://hashcat.net/forum/thread-6661.html)

Detailed description

Tool	Description
wlandump-ng	Small, fast and powerfull deauthentication/authentication/response tool
wlanresponse	Extreme fast deauthentication/authentication/response tool (unattended use on Raspberry Pi's)
wlanrcascan	Small, fast and simple passive WLAN channel assignment scanner (status output)
pioff	Turns Raspberry Pi off via GPIO switch
wlancapinfo	Shows info of pcap file
wlancap2hcx	Converts cap to hccapx and other formats (recommended for use with wlandump-ng and wlanresponse)
wlanhcx2cap	Converts hccapx to cap
wlanhc2hcx	Converts hccap to hccapx
wlanwkp2hcx	Converts wpk (ELMCOMSOFT EWSA projectfile) to hccapx
wlanhcx2essid	Merges hccapx containing the same ESSID
wlanhcx2ssid	Strips BSSID, ESSID, OUI
wlanhcxinfo	Shows detailed info from contents of hccapxfile
wlanhcxmnc	Help to calculate hashcat's nonce-error-corrections value on byte number xx of an anonce
wlanhashhcx	Generate hashlist from hccapx hashfile (md5_64 hash:mac_ap:mac_sta:essid)
wlanhcxcat	Simple password recovery tool for WPA/WPA2/WPA2 SHA256 AES-128-CMAC (hash-modes 2500, 2501)
wlanpmk2hcx	Converts plainmasterkey and ESSID for use with hashcat hash-mode 12000
wlanjohn2hcx	Converts john wpapsk hashfiles for use with hashcat hash-modes 2500, 2501
wlancow2hcxpmk	Converts pre-computed cowpatty hashfiles for use with hashcat hash-mode 2501
wlanhcx2john	Converts hccapx to format expected by John the Ripper
wlancap2wpasec	Upload multiple caps to http://wpa-sec.stanev.org
whoismac	Show vendor information and/or download oui reference list

Compile

Simply run:

make
make install (as super user)

or (with GPIO support - hardware mods required)

make GPIOSUPPORT=on
make GPIOSUPPORT=on install (as super user)

Requirements

Linux (recommended Arch, but other distros should work, too). Don't use Kernel 4.4 (rt2x00 driver regression)
libpcap and pcap-dev installed
libopenssl and openssl-dev installed
librt and librt-dev installed (should be installed by default)
libcurl and curl-dev installed (used by whoismac and wlancap2wpasec)
Raspberry Pi: additionally libwiringpi and wiringpi dev installed (Raspberry Pi GPIO support)
Chipset must be able to run in monitor mode. Recommended: RALINK chipset (good receiver sensitivity), rt2x00 driver (stable and fast)
Raspberry Pi (Recommended: A+ = very low power consumption or B+), but notebooks and desktops should work, too.

Useful scripts

Script	Description
bash_profile	Autostart for Raspberry Pi (copy to /root/.bash_profile)
pireadcard	Back up a Pi SD card
piwritecard	Restore a Pi SD card
makemonnb	Example script to activate monitor mode
killmonnb	Example script to deactivate monitor mode

Notice

Most output files will be appended to existing files (with the exception of .cap files).

Hardware mod (wlandump-ng/wlanresponse)

LED flashes 5 times if wlandump-ng/wlanresponse successfully started

LED flashes every 5 seconds if everything is fine

Press push button at least > 5 seconds until LED turns on (LED turns on if wlandump-ng/wlanresponse terminates)

Green ACT LED flashes 10 times

Raspberry Pi turned off and can be disconnected from power supply

Do not use wlandump-ng, wlanresponse or pioff together!

Hardware mod (pioff)

LED flashes every 30 seconds 2 times if pioff successfully started

Press push button at least > 5 seconds until LED turns on (pioff will shut down Raspberry Pi safely)

Green ACT LED flashes 10 times

Raspberry Pi turned off and can be disconnected from power supply

Do not use wlandump-ng, wlanresponse or pioff together!

Berkeley Packet Filter BPF (example)

wlan host = filter all hosts using this mac

wlan dst = filter all destinations using this mac

wlan src = filter all sources using this mac

wlan ta = filter all transmitter addresses using this mac

wlan ta = filter all receiver addresses using this mac

write all filter entries into one single line !(filterenty1 || filterenty2 || filterenty2)

use ! (not) to filter entries out

!(wlan host 00:00:00:00:00:00 || wlan dst 00:00:00:00:00:00 || wlan src 00:00:00:00:00:00 || wlan ta 00:00:00:00:00:00 || wlan ra 00:00:00:00:00:00)

or allow only this entries

(wlan host 00:00:00:00:00:00 || wlan dst 00:00:00:00:00:00 || wlan src 00:00:00:00:00:00 || wlan ta 00:00:00:00:00:00 || wlan ra 00:00:00:00:00:00)

Warning

You must use wlandump-ng and wlanresponse only on networks you have permission to do this, because

wlandump-ng/wlanresponse are able to prevent complete wlan traffic
wlandump-ng/wlanresponse are able to capture handshakes from not connected clients (only one single M2 from the client is required)
wlandump-ng/wlanresponse are able to capture handshakes from 5GHz clients on 2.4GHz (only one single M2 from the client is required)
wlandump-ng/wlanresponse are able to capture extended EAPOL (RADIUS, GSM-SIM, WPS)
wlandump-ng/wlanresponse are able to capture passwords from the wlan traffic
wlandump-ng/wlanresponse are able to capture plainmasterkeys from the wlan traffic
wlandump-ng/wlanresponse are able to capture usernames and identities from the wlan traffic

evilmog / hcxtools