ASUS Router Check WAN status
This script can monitor the connection status of a WAN interface, and if the status is found to be unacceptable, can perform one of the following:
1. Report the status of the WAN connection.
2. Attempt to restart the WAN interface.
3. REBOOT the router.
The monitoring method is either
-
A simple PING to 5 predefined target PING hosts
ISP WAN_gateway ISP_DNS x 2 8.8.8.8 (Google Primary DNS) 1.1.1.1 (Cloudflare Primary DNS) or a custom list of WAN PING targets e.g. ping=9.9.9.9,185.228.168.9 (Quad9 Primary DNS, Clean Browsing Primary) -
A cURL data transfer retrieval from the WAN - either a 15 Byte (default) or either a ~500 Byte or 12MB.
**Beware if using a metered connection!** Optionally an expected transfer rate may be specified to perform the desired action if the transfer is deemed slow.
NOTE: Only one of the test criteria needs to succeed, i.e. if 5 PING hosts are used, the test will terminate with the first successful host that responds to the PING - ignoring the others.
To prevent transient false positives, the number of retries and a maximum number of fails permitted for each method defaults to retries=3 and fails=3, and be tailored e.g. retries=1 fails=1 whilst the result being immediate, may seemingly fail, due to the PING or cURL target entity being briefly unavailable
The complete list of command options may be retrieved using
ChkWAN.sh help
#============================================================================================ © 2016-2020 Martineau v1.15
#
# Monitor WAN connection state using PINGs to multiple hosts, or a single cURL 15 Byte data request and optionally a 12MB/500B WGET/CURL data transfer.
# NOTE: The cURL data transfer rate/perfomance threshold may also be checked e.g. to switch from a 'slow' (Dual) WAN interface.
# Usually the Recovery action (REBOOT or restart the WAN) occurs in about 90 secs (PING ONLY) or in about 03:30 mins for 'force' data download
#
# Usage: ChkWAN [help|-h]
# [reboot | wan | noaction] [force[big | small]] [nowait] [quiet] [once] [i={[wan0|wan1]}] [googleonly] [curl] [ping='ping_target[,..]']
# [tries=number] [fails=number] [curlrate=number] [verbose] [cron[=[cron_spec]]] [status] [stop]
#
# ChkWAN
# Will REBOOT router if the PINGs to ALL of the hosts FAILS
# ChkWAN force
# Will REBOOT router if the PINGs to ALL of the hosts FAIL, but after each group PING attempt, a physical 12MByte data download is attempted.
# ChkWAN forcesmall
# Will REBOOT router if the PINGs to ALL of the hosts FAIL, but after each group PING attempt, a physical 500Byte data download is attempted.
# (For users on a metered connection assuming that the 15Byte cURL is deemed unreliable?)
# ChkWAN status
# Will report if Check WAN monitor is running
# ChkWAN wan
# Will restart the WAN interface (instead of a FULL REBOOT) if the PINGs to ALL of the hosts FAIL
# ChkWAN stop
# Will request termination of script. It will be dependent on the 'sleep' interval
# NOTE: If scheduled by cron this will have no effect.
# ChkWAN curl
# Will REBOOT router if cURL (i.e. NO PINGs attempted) fails to retrieve the remote end-point IP address of the WAN (Max 15bytes)
# ChkWAN cron
# Will REBOOT router if the PINGs to ALL of the hosts FAILS, cron entry is added: Runs every 30mins.
# 'cru a ChkWAN "*/30 * * * * /jffs/scripts/ChkWAN.sh"'
# ChkWAN cron=\*/5
# Will REBOOT router if the PINGs to ALL of the hosts FAILS, cron entry is added: Runs every 5mins.
# 'cru a ChkWAN "*/5 * * * * /jffs/scripts/ChkWAN.sh"'
# NOTE: You need to escape the '*' on the commandline :-(
# ChkWAN nowait
# By default the script will wait 10 secs before actually starting the check; 'nowait' (when used by cron) skips this delay.
# ChkWAN googleonly
# Only the two Google DNS severs will be PING'd - WAN Gateway/local DNS config will be ignored
# ChkWAN i=wan1 noaction
# In a Dual-WAN environment check WAN1 interface, but if it's DOWN simply return RC=99
# ChkWAN ping=1.2.3.4,1.1.1.1
# PING the two hosts 1.2.3.4 and 1.1.1.1, rather than the defaults.
# ChkWAN tries=1 fails=1
# Reduce the number of retry attempts to 1 instead of the default 3 and maximum number of fails is 1 rather than 3
# ChkWAN force curlrate=1000000
# If the 12MB average curl transfer rate is <1000000 Bytes per second (1MB), then treat this as a FAIL
# ChkWAN curl verbose
# The 'verbose' directive applies to any cURL transfer, and will display the cURL request data transfer as it happens
Installation
Enable SSH on router, then use your preferred SSH Client e.g. Xshell6,MobaXterm, PuTTY etc. to copy'n'paste:
curl --retry 3 "https://raw.githubusercontent.com/MartineauUK/Chk-WAN/master/ChkWAN.sh" -o "/jffs/scripts/ChkWAN.sh" && chmod 755 "/jffs/scripts/ChkWAN.sh"
You can manually test the script with the default PING method, and the script will simply passively report the status, rather proactively restart the WAN or REBOOT
./ChkWAN.sh noaction once nowait
but for automated monitoring, you would include the call to the script in
/jffs/scripts/wan-start
sh /jffs/scripts/ChkWAN.sh &
or use cru (cron) to schedule the script at a pre-determined scheduled time) NOTE: You could configure the cron schedule such that the scipt will restart the WAN say 3 times, but every fourth attempt will action the REBOOT.