This layer provides BSP for the a Custom STM32 board (based on STM32MP157a-DK1)
This layer depends on:
-
URI: git://git.yoctoproject.org/poky
- branch: kirkstone
- layers: meta
-
URI: https://source.denx.de/denx/meta-mainline-common.git
- branch: dunfell-3.1
A good starting point for setting up the build environment is is the official Yocto Project wiki.
Before attempting the build, the following metalayer git repositories shall be cloned into a location accessible to the build system and a branch listed below shall be checked out. The examples below will use /path/to/OE/ as a location of the metalayers.
- https://source.denx.de/denx/meta-mainline-common.git (branch: kirkstone)
- https://github.com/andreluizeng/meta-dk1-stm32-bsp.git (branch: master)
- git://git.yoctoproject.org/poky (branch: kirkstone)
With all the source artifacts in place, proceed with setting up the build using oe-init-build-env as specified in the Yocto Project wiki: /path/to/OE/poky $ source oe-init-build-env
In addition to the content in the wiki, the aforementioned metalayers shall be referenced in bblayers.conf in this order:
BBLAYERS ?= " \
/path/to/OE/poky/meta \
/path/to/OE/meta-mainline-common \
/path/to/OE/meta-dk1-stm32-bsp \
"
The following specifics should be placed into local.conf:
MACHINE = "custom-stm32-dk1"
DISTRO = "nodistro"
Note that MACHINE must be:
- custom-stm32-dk1
Adapt the suffixes of all the files and names of directories further in this documentation according to MACHINE.
Both local.conf and bblayers.conf are included verbatim in full at the end of this readme.
Once the configuration is complete, a basic demo system image suitable for evaluation can be built using:
$ bitbake core-image-minimal
Once the build completes, the images are available in:
tmp-glibc/deploy/images/custom-stm32-dk1/
The SD card is specifically in:
core-image-minimal-custom-stm32-dk1.wic.gz
And shall be written to the SD card via the following commands from the U-Boot prompt:
gunzip core-image-minimal-custom-stm32-dk1.wic.gz
sudo dd if=core-image-minimal-custom-stm32-dk1.wic of=/dev/sdX; sudo sync
MACHINE = "custom-stm32-dk1"
DL_DIR = "/path/to/OE/downloads"
DISTRO ?= "nodistro"
PACKAGE_CLASSES ?= "package_rpm"
EXTRA_IMAGE_FEATURES = "debug-tweaks"
USER_CLASSES ?= "buildstats"
PATCHRESOLVE = "noop"
BB_DISKMON_DIRS = "\
STOPTASKS,${TMPDIR},1G,100K \
STOPTASKS,${DL_DIR},1G,100K \
STOPTASKS,${SSTATE_DIR},1G,100K \
STOPTASKS,/tmp,100M,100K \
HALT,${TMPDIR},100M,1K \
HALT,${DL_DIR},100M,1K \
HALT,${SSTATE_DIR},100M,1K \
HALT,/tmp,10M,1K"
PACKAGECONFIG:append:pn-qemu-native = " sdl"
PACKAGECONFIG:append:pn-nativesdk-qemu = " sdl"
CONF_VERSION = "2"
# LAYER_CONF_VERSION is increased each time build/conf/bblayers.conf
# changes incompatibly
POKY_BBLAYERS_CONF_VERSION = "2"
BBPATH = "${TOPDIR}"
BBFILES ?= ""
BBLAYERS ?= " \
/path/to/OE/poky/meta \
/path/to/OE/meta-mainline-common \
/path/to/OE/meta-dk1-stm32-bsp \
"
# Get Yocto (kirkstone) source and dependencies
$ git clone http://git.yoctoproject.org/git/poky -b kirkstone yocto
$ cd yocto
$ git clone https://source.denx.de/denx/meta-mainline-common.git -b kirkstone
$ git clone https://github.com/andreluizeng/meta-dk1-stm32-bsp.git
# Set the build environment
$ source oe-init-build-env build-custom-stm32-dk1
# Change the local.conf and bblayers.conf as presented before (example of local.conf and bblayers.conf)
# Build the minimal image
$ bitbake core-image-minimal