Xilinx Zynq Ultrascale+ MPSoC Series Development Board Z19

Introduction to Development Board

The development board mainly consists of ZU19EG+4 DDR4+DDR4 SODIMMs+eMMC+2 QSPI FLASH Composition. The main chip is a Zynq UltraScale+MPSoCs series chip from Xilinx Company, with a model of XCZU19EG- -2FFVC1760I。 Four DDR4 chips are attached to the PS terminal and the PL terminal of the ZU19EG chip And a 260 pin DDR4 SODIMM card slot, with a PS side DDR4 capacity of up to 2GB per chip, enabling the ARM system and The ability of an FPGA system to independently process and store data. 32GB eMMC FLASH memory chip and 2 chips on the PS side The 512Mb QSPI FLASH is used to statically store the operating system, file system, and user data of MPSoCs. The development board has extended a variety of peripheral interfaces, including two FMC dual width interfaces, one M.2 SSD interface, and one PCIE main mode slot, 4-way SATA interface, 3-pair differential SMA interface, 1-way mini_ DP interface, 4-way QSFP28 Optical fiber interface, 4 USB 3.0 interfaces, 2 Gigabit Ethernet interfaces, 3 UART interfaces, 1 TF card slot, 2 channels CAN bus interface, 2-way RS485 interface, 1-way MIPI camera interface, and some key LEDs.

Key Features

Four Micron DDR4 chips (ps) with a capacity of 1Gx16bit and a model of MT40A1G16KD-062E
One 260 pin DDR4 SODIMM slot on the pl end
Two 512Mbit Quad-SPI flash drives with a capacity of 512Mbit and a model of MT25QU512ABB1EW9-0SIT
One 32GB eMMC FLASH chip with the model of Micron's MTFC32GAPALBH-IT
1-way M.2 interface, PCIEx1 (ps), speed 6Gbps
1-channel DP output interface, mini DP (ps), maximum support 4kx2k@30fps Output
4-way USB 3.0 interface, USB (ps), speed 5.0Gbps, flat USB interface (USB Type A)
2-way Gigabit Ethernet interface, jl2121, 1-way ps, 1-way pl, rgmii interface
Three uart interfaces, two of which are led out through uart to usb chips, respectively connected to pl and ps, and the remaining one is led out through a 1 mm spacing, 10 pin fpc connector
1 Micro SD card holder (ps)
4-way QSFP28 optical fiber interface with a speed of 25Gbps
2-way CAN communication interface (ps)
2-way 485 communication interface (PL)
1-way mipi interface (pl), 15PIN FPC connector, 2 lane data, 1 pair of clocks
Two FMC HPC expansion ports
1 main mode PCIEx8 slot
4-way SATA interface
3 pairs of differential lines, 6 SMA interface outputs
1 RTC real-time clock, 32.768KHz passive clock (ps)
EEPROM and temperature sensor, one EEROM 4Kbit (2x256x8bit) (ps), one LM75 temperature chip (ps), with an accuracy of 0.5 degrees
Four LED lights, one Done indicator light, one power supply, one PL control, and one PS control
Three buttons, one reset button RESET, and two user buttons
One 4-bit dial switch, and the board supports four startup modes
Size 250mm x 170mm
Power supply 12v/3A

Z19 Demo Project

Description

This is vivado factory demo project for ALINX board.

Requirement

Vivado 2020.1
Z19 Development Board

Create Vivado Project

Download recent release ZIP archive.
Create new project folder.
Extract the download ZIP to the new project folder.

There are two methods to create vivado project as below:

Create Vivado Project in Vivado tcl console

Open Vivado software and switch to "auto_create_project" path with cd command and Enter

cd \<archive extracted location\>/vivado/auto_create_project

Type source ./create_project.tcl and Enter

source ./create_project.tcl

Create Vivado Project using bat

In "auto_create_project" folder, there is "create_project.bat", open it in edit mode, and change to your own vivado software installation path. Save and close.

CALL E:\XilinxVitis\Vivado\2020.1\bin\vivado.bat -mode batch -source create_project.tcl
PAUSE

Double click bat file in Windows environment

For more information, please post on the [ALINX Website] (https://www.alinx.com/en).

alinxalinx / Z19