RealNobser / PenumbraShadowMD

Penumbra Shadow MD

This is a modified Shadow sketch to work with the Penumbra controller.

Libraries Used

• https://github.com/reeltwo/Reeltwo
• https://github.com/rimim/espsoftwareserial
• https://github.com/reeltwo/USB_Host_Shield_2.0
• https://github.com/DFRobot/DFRobotDFPlayerMini

Web Installer

A web-based installer for the latest firmware can be found here: https://reeltwo.github.io/Penumbra-Installer/

Build using Arduino IDE

The firmware should build with esp32 board package 1.0.6 or 2.0.5. For ESP32S2 support 2.0.5 is required.

Build using command line tools (Mac)

cd ~/Documents/Arduino
curl -o Arduino.mk https://raw.githubusercontent.com/reeltwo/Arduino/master/Arduino.mk
# Fetch repository
git clone https://github.com/reeltwo/PenumbraShadowMD
# Enter directory
cd PenumbraShadowMD
# Build firmware
make

Build using command line tools (Linux)

cd ~/Arduino
wget https://raw.githubusercontent.com/reeltwo/Arduino/master/Arduino.mk
# Fetch repository
git clone https://github.com/reeltwo/PenumbraShadowMD
# Enter directory
cd PenumbraShadowMD
# Build firmware
make

Sample wiring diagram for Penumbra Shadow

Command Reference

#SMRESTART

Restart the controller.

#SMRESTART

#SMZERO

Delete all preferences, reset button triggers to sketch defaults, unpair controllers.

#SMZERO

#SMLIST

List all button triggers and associated commands.

#SMLIST

#SMVOLUME<0-1000>

Set the volume to the specified value.

#SMVOLUME500

#SMSTARTUP file number

Set the startup sound to the specified file number.

#SMSTARTUP255

#SMRANDMIN milliseconds

Set the minimum delay before playing the next random sound.

#SMRANDMIN600

#SMRANDMAX milliseconds

Set the maximum delay before playing the next random sound.

#SMRANDMAX10000

#SMRAND0

Disable random sound playback.

#SMRAND0

#SMRAND1

Enable random sound playback.

#SMRAND1

#SMSET trigger action

Set the button trigger (trigger) to the specified action (action).

#SMSET btnUP_MD $83

To send direct Marcduino commands prefix the command with " and separate with ,
#SMSET btnUP_MD "BM:OP03,"BM*ON01
#SMSET btnUP_CIRCLE_MD ":OP03,"BM*ON01

" followed by BM is sent to body Marcduino

#SMPLAY trigger

Play any action associated with the specified trigger

#SMPLAY btnUP_MD

#SMDEL trigger

Reset command for specified trigger to sketch default.

#SMDEL btnUP_MD

#SMSOUND [0,1,2,3]

Set the sound output module to of the following:

• 0: Disabled
• 1: MP3 Trigger
• 2: DFMini Player
• 3: HCR Vocalizer

#SMSOUND 3

#SMCONFIG

Display the current drive configuration

#SMCONFIG

#SMNORMALSPEED[0..127]

Set the normal drive speed: set this to whatever speeds works for you. 0-stop, 127-full speed. Default is 70.

#SMNORMALSPEED70

#SMMAXSPEED[0..127]

Set the over throttle drive speed: set this to whatever speeds works for you. 0-stop, 127-full speed. Default is 100.

#SMMAXSPEED100

#SMTURNSPEED[0..127]

Set the drive turn speed. The higher this number the faster it will spin in place, lower - the easier to control. Recommend beginner: 40 to 50, experienced: 50+, I like 75. Default is 50.

#SMTURNSPEED50

#SMDOMESPEED[0..127]

Set the dome drive top speed. Default is 100.

#SMDOMESPEED100

#SMRAMPING[0..10]

Set drive speed ramping. The lower this number the longer it will take to speedup or slow down. Default is 1.

#SMRAMPING1

#SMFOOTDB[0..127]

Set the foot controller joystick deadband. Use the lowest number with no drift. Default is 15

#SMFOOTDB15

#SMDOMEDB[0..127]

Set the dome controller joystick deadband. Use the lowest number with no drift. Default is 10

#SMDOMEDB15

#SMDRIVEDB[0..127]

Set the drive motor controller deadband. Use the lowest number with no drift. Default is 10

#SMDRIVEDB10

#SMINVERT[0..1]

Set the turn direction inversion. Default is 0.

#SMINVERT0

#SMAUTOSPEED[50..100]

Set the dome speed used when dome automation is active. Default is 70.

#SMAUTOSPEED70

#SMAUTOTIME[2500..8000]

Set the number of milliseconds for dome to complete 360 turn at #SMAUTOSPEED. Default is 2500.

#SMAUTOTIME2500

#SMMOTORBAUD[2400..115200]

Sets the baud rate of the packet serial connection to the motor controller. Default is 9600.

#SMMOTORBAUD9600

#SMMARCBAUD[2400..115200]

Sets the baud rate of the command seriall connection. Default is 9600.

#SMMARCBAUD9600