NAME CHANGE IN LIBRARAY MANAGER - PLEASE READ

Hi all DIY gaming enthusiasts. Please be aware that the official name for this library in the library manager has changed from

ESP32 BLE Gamepad  -->  ESP32-BLE-Gamepad

This is to make it consistent with those who were also downloading it from GitHub and had 2 versions with different names and was leading to confusion. The library manager was automatically renaming the folder ESP32_BLE_Gamepad upon installation due to the spaces in the name. The library with the old name has been de-listed from the manager and only the new one remains. Please remove/delete the old version by deleting the ESP32_BLE_Gamepad folder within your libraries folder.

Apologies for the early adopters, but it will save a lot of confusion moving forward.

NimBLE

Since version 3 of this library, the more efficient NimBLE library is used instead of the default BLE implementation Please use the library manager to install it, or get it from here: https://github.com/h2zero/NimBLE-Arduino Since version 3, this library also supports a configurable HID desciptor, which allows users to customise how the device presents itself to the OS (number of buttons, hats, ases, sliders, simulation controls etc). See the examples for guidance.

ESP32-BLE-Gamepad

License

Published under the MIT license. Please see license.txt.

It would be great however if any improvements are fed back into this version.

Features

Installation

(Make sure you can use the ESP32 with the Arduino IDE. Instructions can be found here.)
Download the latest release of this library from the release page.
In the Arduino IDE go to "Sketch" -> "Include Library" -> "Add .ZIP Library..." and select the file you just downloaded.
In the Arduino IDE go to "Tools" -> "Manage Libraries..." -> Filter for "NimBLE-Arduino" by h2zero and install.
You can now go to "File" -> "Examples" -> "ESP32 BLE Gamepad" and select an example to get started.

Example

/*
 * This example turns the ESP32 into a Bluetooth LE gamepad that presses buttons and moves axis
 * 
 * Possible buttons are:
 * BUTTON_1 through to BUTTON_16 
 * (16 buttons supported by default. Library can be configured to support up to 128)
 * 
 * Possible DPAD/HAT switch position values are: 
 * DPAD_CENTERED, DPAD_UP, DPAD_UP_RIGHT, DPAD_RIGHT, DPAD_DOWN_RIGHT, DPAD_DOWN, DPAD_DOWN_LEFT, DPAD_LEFT, DPAD_UP_LEFT
 * (or HAT_CENTERED, HAT_UP etc)
 *
 * bleGamepad.setAxes takes the following int16_t parameters for the Left/Right Thumb X/Y, Left/Right Triggers plus slider1 and slider2, and hat switch position as above: 
 * (Left Thumb X, Left Thumb Y, Right Thumb X, Right Thumb Y, Left Trigger, Right Trigger, Hat switch position 
 ^ (1 hat switch (dpad) supported by default. Library can be configured to support up to 4)
 *
 * Library can also be configured to support up to 5 simulation controls (can be set with setSimulationControls)
 * (rudder, throttle, accelerator, brake, steering), but they are not enabled by default.
 */
 
#include <BleGamepad.h> 

BleGamepad bleGamepad;

void setup() 
{
  Serial.begin(115200);
  Serial.println("Starting BLE work!");
  bleGamepad.begin();
  // The default bleGamepad.begin() above is the same as bleGamepad.begin(16, 1, true, true, true, true, true, true, true, true, false, false, false, false, false);
  // which enables a gamepad with 16 buttons, 1 hat switch, enabled x, y, z, rZ, rX, rY, slider 1, slider 2 and disabled rudder, throttle, accelerator, brake, steering
  // Auto reporting is enabled by default. 
  // Use bleGamepad.setAutoReport(false); to disable auto reporting, and then use bleGamepad.sendReport(); as needed
}

void loop() 
{
  if(bleGamepad.isConnected()) 
  {
    Serial.println("Press buttons 5 and 16. Move all enabled axes to max. Set DPAD (hat 1) to down right.");
    bleGamepad.press(BUTTON_5);
    bleGamepad.press(BUTTON_16);
    bleGamepad.setAxes(32767, 32767, 32767, 32767, 32767, 32767, 32767, 32767, DPAD_DOWN_RIGHT);
    // All axes, sliders, hats etc can also be set independently. See the IndividualAxes.ino example
    delay(500);

    Serial.println("Release button 5. Move all axes to min. Set DPAD (hat 1) to centred.");
    bleGamepad.release(BUTTON_5);
    bleGamepad.setAxes(-32767, -32767, -32767, -32767, -32767, -32767, -32767, -32767, DPAD_CENTERED);
    delay(500);
  }
}

By default, reports are sent on every button press/release or axis/slider/hat/simulation movement, however this can be disabled, and then you manually call sendReport on the gamepad instance as shown in the IndividualAxes.ino example.

There is also Bluetooth specific information that you can use (optional):

Instead of BleGamepad bleGamepad; you can do BleGamepad bleGamepad("Bluetooth Device Name", "Bluetooth Device Manufacturer", 100);. The third parameter is the initial battery level of your device. Adjusting the battery level later on doesn't work. By default the battery level will be set to 100%, the device name will be ESP32 BLE Gamepad and the manufacturer will be Espressif.

Credits

Credits to T-vK as this library is based on his ESP32-BLE-Mouse library (https://github.com/T-vK/ESP32-BLE-Mouse) that he provided.

Credits to chegewara as the ESP32-BLE-Mouse library is based on this piece of code that he provided.

Credits to wakwak-koba for the NimBLE code that he provided.

Notes

This library allows you to make the ESP32 act as a Bluetooth Gamepad and control what it does.
Relies on NimBLE-Arduino

Use this Windows test app to test/see all of the buttons

About

Bluetooth LE Gamepad library for the ESP32

Other

Languages

Language:C++ 100.0%