MicroPython P1 meter

Overview

If you want to monitor your energy usage

The P1_Meter is a a sensor device that:

connects to your electricity meter's P1 port
Reads the P1 output using one of the ESP32 hardware UARTs
reads the OBIS coded information
runs a CRC check on the received information to suppress incorrect readings
translates the OBIS codes to readable topics
publishes the information to a MQTT server on your network
so you can read the information in HomeAssistant (or any other tool)
uses mDns to simplify configuration and avoid the need for fixed IP addresses or static DNS leases
allows the configuration to be changed though a simple config file

in addition it:

logs a few relevant sensors statistics to MQTT (client_id, free memory, CPU core temperature)
Allows you to view logs and other terminal output over wifi via the webrepl
Allows you to update update the configuration over the network using FTP
how does it work

[Diagram]
show me some pictures [a few screenshots / photos]

Hardware & Firmware

Hardware:

Any ESP32 board no SPI ram is required, the firmware auto detects if it is present and runs on either.
A single 1K Ohm resistor
A cable with a 4 or 6 pin RJ12 connector (optionally a 4 pin RJ11 connector and be used)
Some sort of casing
Optional: a sort strip of 3 neopixels to use as indicators.

Firmware:

Use micropython 1.13 for or newer for the esp32 http://micropython.org/download/esp32/ you can download the firmware directly from
- ESP32 GENERIC-SPIRAM : esp32spiram-idf3-20200902-v1.13.bin
Install the micropython firmware to the ESP32 using the procedure documented in: Getting started with MicroPython on the ESP32 — MicroPython 1.13 documentation
the code in this repo; see the next paragraph.

Install the P1 meter software on the ESP32 MCU

git clone this repo
adjust config.py settings :
- homenet : WiFi SSID and Password
- broker : MQtt broker address, port, user and password
- RX pins to connect to the P1 Port
- Options (TX pin if you want to test drive without a connection to a P1 port)
upload code from /src folder to the board
- flash Micropython 1.13 or newer ( 1 time)
- upload the source code ( using pymakr or any other tool)
reboot the board

Assembling the P1 meter circuit diagram

the circuit is quite simple:

ESP32, any devkit will do and will allow you to simply flash the Firmware and power the ESP by USB
a 1K Ohm resistor , needed to stabilize the serial data by pulling it to +3.3 volt
a female RJ-12 (or RJ11) connector, or you could solder a 4 wire phone cable directly to the board optionally
some sort of case / box or container
a small piece of perfboard , although if you want it should be able to solder directly on the devkit as well
a string of 3 neopixel leds to provide status on Network , MQTT and the received P1 data, if you rather want a few simple leds to provide signals there are enough pins left , but switched to neopixels to simplify the wiring. the code should be in one of the earlier commits.

The ESP hardware UART 1 is used to connect to pin 2 ( you specify in config.py this allows normal functionality to use the USB port (UART 0) for configuration and monitoring of the ESP32.

Connection to P1 meter

The RJ12 connector in the electricity meter uses the following layout

Connect the ESP32 to an RJ12 cable/connector using the below diagram.

Connection via straight 4/6 wire cable :
Note: This will reverse the pin numbers on the female connector that you are using

RJ12 P1	cable	RJ12 Meter	ESP32 Pin	RJ12 6w cable	4w cable	comments
1 - 5v out	===>	6	5v or Vin			[Optional] 1️⃣
2 - CTS	<---	5	gpio-5	blue	black	Clear to Send, High = allow P1 Meter to send data
3 - Data GND	----	4	GND	black	red
4 - nc		3	-		green
5 - RXD (data)	--->	2	gpio-15	yellow	yellow	1K external pull-up resistor needed
6 - Power GND	<===	1	GND			[Optional] 1️⃣

1️⃣ max 250 mA When using a 6 pin cable you can use the power source provided by the meter.

Adjusting for Straight or Cross cables

If you are unsure which cable will be used to connect, or if you want to build some flexibility in your hardware design , it is possible to allow both cable types by :

Output connecting both Pin 3 and Pin 4 Ground

this will ten allow you to swap the functions of pin 18 and 19 from

CTS / RXD for a straight cable
RDX / CTS for a cross cable

RJ12 P1	cable	Straight Cable	Cross Cable	-
1 - 5v out	===>	1	6	not connected
2 - CTS	<---	2	5	CTS / RXD software select
3 - GND data	----	3	4	\ GND
4 - GND data	----	4	3	/ GND
5 - RXD (data)	--->	5	2	RDX / CTS software select
6 - GND power	<===	6	1	not connected

I recommend that in this design you do not connect the Power 5v to your board

Internal wiring:

P1 In Connector

ESP32 Pin	Color	Female Connector
GND	black	pin 4 & 3
gpio-2	pale blue	pin 5
gpio-5	yellow/blk	pin 2

operation

3 Neopixel Leds (top to bottom):

led	purpose	Red	Green	other
2	P1 meter	CRC Error	CRC OK	Blue: data received , Purple : Simulator sending Data
1	mqtt	Not connected	Connected to MQTT broker	Yellow: Data could not be send to Broker
0	wifi	Not connected	IP address acquired

configuration file

Please adjust the relevant settings in config.py

# Serial Pins for meter connection
# TX pin is only used for testing/simulation but needs to be specified
RX_PIN_NR = const(2)
TX_PIN_NR = const(15)
RTS_PIN_NR = const(5)

# Base SSID to connect to
homenet = {'SSID': 'IoT', 'password': 'MicroPython'}

#the mqtt broker to connect to
broker = {'server': 'homeassistant.local', 'user': 'sensor', 'password': 'beepbeep'}

HOST_NAME = b'p1_meter_' + hexlify(unique_id())
ROOT_TOPIC = b"p1_meter"

#also publish telegram as json
publish_as_json = False

Updating the configuration over WiFi

Assuming that you have cloned the repo to your PC , and have updated the configuration file config.py . You will need to transfer the updated configuration file to the ESP32.

You can do this via serial connection, or as the P1_meter and your pc are likely in in different locations you can do this over WifI

Uploading config.py using webrepl

The MicroPython webrepl is started as part of the standard configuration, and advertises itself as p1_meter.local using the standard webrepl port (8266).

If you are on the same network , this allows you to connect to the P1_meter to verify its operation.

The below link uses the hosted webrepl, and specifies the board to connect to. http://micropython.org/webrepl/#p1_meter.local:8266/

[Connect] to the board
Enter the current webrepl password. default: p1meter
Select the config.py file to upload
click [Send to device]
Click in the terminal window

Press Ctrl-C once, to interrupt the running instance. You should see something like the below, and the 3 leds will turn red

INFO     mqttclient Published 4 meter readings                                  
INFO     main       Clear async loop retained state                             
Rebooting in 30 seconds, Ctrl-C to abort

the device will automatically reboot in 30 seconds, and the new configuration will be activated.

Updating configuration or code via passive ftp

Prereqs :

git client
python 3.x installed

Building

As the software is written in Micropython building is not needed. if you really want or need to minimize the footprint on the device you can pre-compile the .py files to .mpy using the micropython cross-compiler

Testing

You can run the built-in simulator for testing (using TX_PIN_NR)

connect the rx and tx pins with a wire

  # Serial Pins for meter connection
  # TX pin is only used for testing/simulation but needs to be specified
  RX_PIN_NR = const(2)
  TX_PIN_NR = const(15)
  CTS_PIN_NR = const(5)

  #------------------------------------------------
  # A few Leds - optional
  NEOPIXEL_PIN = const(13)

- edit the configuration file `config.py` to enable the Simulator

    RUN_SIM = True

Simulation / test mode

The p1 meter comes with a built-in test and simulation mode that allows you to test and change the software, without needing to physically connect it to a electricity meter.

this simulation mode can be enabled by wiring, or by making a change to the config.py file

To enable this via wiring:

Connect Pin 18 --> GND , enable Simulator
Connect Pin 15 --> Pin 2 , connect simulator TX to RX

By default:

the root topic is changed
a fake P1 message is generated every 10 seconds on Pin 15
- this message has a few random values added to it
- the CRC16 is calculated before sending
the message is passed of the serial connect ( see .2 above) to the input
the message is is processed by the normal software and sent to mqtt using a different root topic to avoid interfering with actual input..

To change the fake message see p1meter_sym.py

Josverl / micropython-p1meter