WiringOP-Zero
WiringPi / WiringOP libary for the Orange Pi Zero with 26 pin GPIO header
This is a modified WiringPi for specially OrangePi Zero.
GPIO is fully working, i2c not tested yet!
SPI is tested on Armbian with legacy kernel:
The SPI channel 0 is used for SPI Flash and channel 1 is available
for use in GPIO pins...
> bin2fex /boot/script.bin script.fex
> nano script.fex
Add following lines:
[spi1_para]
spi_used = 1
spi_cs_bitmap = 1
spi_cs0 = port:PA13<2><1><default><default>
spi_sclk = port:PA14<2><default><default><default>
spi_mosi = port:PA15<2><default><default><default>
spi_miso = port:PA16<2><default><default><default>
[spi_devices]
spi_dev_num = 2
[spi_board1]
modalias = "spidev"
max_speed_hz = 33000000
bus_num = 1
chip_select = 0
mode = 0
full_duplex = 1
manual_cs = 0
> fex2bin script.fex bin/orangepizero.bin
> reboot -i
Download
git clone https://github.com/xpertsavenue/WiringOP-Zero.git
Installation
cd WiringOP-Zero
chmod +x ./build
sudo ./build
Test
christian@orangepizero:~/WiringOP-Zero$ gpio readall
+-----+-----+----------+------+--Orange Pi Zero--+---+------+---------+-----+--+
| H2+ | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | H2+ |
+-----+-----+----------+------+---+----++----+---+------+----------+-----+-----+
| | | 3.3v | | | 1 || 2 | | | 5v | | |
| 12 | 8 | SDA.0 | ALT5 | 0 | 3 || 4 | | | 5V | | |
| 11 | 9 | SCL.0 | ALT5 | 0 | 5 || 6 | | | 0v | | |
| 6 | 7 | GPIO.7 | ALT3 | 0 | 7 || 8 | 0 | ALT5 | TxD3 | 15 | 198 |
| | | 0v | | | 9 || 10 | 0 | ALT5 | RxD3 | 16 | 199 |
| 1 | 0 | RxD2 | ALT5 | 0 | 11 || 12 | 0 | ALT3 | GPIO.1 | 1 | 7 |
| 0 | 2 | TxD2 | ALT5 | 0 | 13 || 14 | | | 0v | | |
| 3 | 3 | CTS2 | ALT3 | 0 | 15 || 16 | 0 | ALT4 | GPIO.4 | 4 | 19 |
| | | 3.3v | | | 17 || 18 | 0 | ALT4 | GPIO.5 | 5 | 18 |
| 15 | 12 | MOSI | ALT5 | 0 | 19 || 20 | | | 0v | | |
| 16 | 13 | MISO | ALT5 | 0 | 21 || 22 | 0 | ALT3 | RTS2 | 6 | 2 |
| 14 | 14 | SCLK | ALT5 | 0 | 23 || 24 | 0 | ALT5 | CE0 | 10 | 13 |
| | | 0v | | | 25 || 26 | 0 | ALT3 | GPIO.11 | 11 | 10 |
+-----+-----+----------+------+---+---LEDs---+---+------+----------+-----+-----+
| 17 | 30 | STAT-LED | OUT | 0 | 27 || 28 | | | PWR-LED | | |
+-----+-----+----------+------+---+-----+----+---+------+----------+-----+-----+
| H2+ | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | H2+ |
+-----+-----+----------+------+--Orange Pi Zero--+---+------+---------+-----+--+
To control red LED on the board run for example this:
gpio write 30 1
and to turn off this
gpio write 30 0
Thanks to zhaolei, who created the base libary for this one!