ioBroker RPI-Monitor Adapter
RPI-Monitor implementation for integration into ioBroker. It is the same implementation as for iobroker.rpi, but with GPIOs.
Important Information
Works only with node >= 0.12
ioBroker must run under root to may control GPIOs.
Installation
After installation you have to configure all required modules via administration page.
After start of iobroker.rpi, all selected modules generates an object tree in ioBroker within rpi.. e.g. rpi.0.cpu
Be sure, that python and build-essential are installed:
sudo apt-get update
sudo apt-get install -y build-essential python
Following Objects are available after selection:
CPU
- cpu_frequency
- load1
- load5
- load15
Raspberry (vcgencmd is required)
- cpu_voltage
- mem_arm
- mem_gpu
Memory
- memory_available
- memory_free
- memory_total
Network (eth0)
- net_received
- net_send
SDCard
- sdcard_boot_total
- sdcard_boot_used
- sdcard_root_total
- sdcard_root_used
Swap
- swap_total
- swap_used
Temperature
- soc_temp
Uptime
- uptime
WLAN
- wifi_received
- wifi_send
Configuration
On configuration page you can select following modules:
- CPU
- Raspberry
- Memory
- Network
- SDCard
- Swap
- Temperature
- Uptime
- WLAN
Logfiles / Configuration Settings
Features
Todo
Tested Hardware
- Odroid C1
- Raspberry Pi 1
GPIOs
You can read and control GPIOs too. All what you need to do is to configure in the settings the GPIOs options (additional tab).
After some ports are enabled following states appear in the object tree:
- rpi.0.gpio.PORT.state
The numeration of ports is BCM (BroadComm pins on chip). You can get the enumeration with gpio readall
.
For instance PI2:
+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
| BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| | | 3.3v | | | 1 || 2 | | | 5v | | |
| 2 | 8 | SDA.1 | ALT0 | 1 | 3 || 4 | | | 5V | | |
| 3 | 9 | SCL.1 | ALT0 | 1 | 5 || 6 | | | 0v | | |
| 4 | 7 | GPIO. 7 | IN | 1 | 7 || 8 | 0 | IN | TxD | 15 | 14 |
| | | 0v | | | 9 || 10 | 1 | IN | RxD | 16 | 15 |
| 17 | 0 | GPIO. 0 | IN | 0 | 11 || 12 | 0 | IN | GPIO. 1 | 1 | 18 |
| 27 | 2 | GPIO. 2 | IN | 0 | 13 || 14 | | | 0v | | |
| 22 | 3 | GPIO. 3 | IN | 0 | 15 || 16 | 0 | IN | GPIO. 4 | 4 | 23 |
| | | 3.3v | | | 17 || 18 | 0 | IN | GPIO. 5 | 5 | 24 |
| 10 | 12 | MOSI | IN | 0 | 19 || 20 | | | 0v | | |
| 9 | 13 | MISO | IN | 0 | 21 || 22 | 1 | IN | GPIO. 6 | 6 | 25 |
| 11 | 14 | SCLK | IN | 0 | 23 || 24 | 1 | IN | CE0 | 10 | 8 |
| | | 0v | | | 25 || 26 | 1 | IN | CE1 | 11 | 7 |
| 0 | 30 | SDA.0 | IN | 1 | 27 || 28 | 1 | IN | SCL.0 | 31 | 1 |
| 5 | 21 | GPIO.21 | IN | 1 | 29 || 30 | | | 0v | | |
| 6 | 22 | GPIO.22 | IN | 1 | 31 || 32 | 0 | IN | GPIO.26 | 26 | 12 |
| 13 | 23 | GPIO.23 | IN | 0 | 33 || 34 | | | 0v | | |
| 19 | 24 | GPIO.24 | IN | 0 | 35 || 36 | 0 | IN | GPIO.27 | 27 | 16 |
| 26 | 25 | GPIO.25 | OUT | 1 | 37 || 38 | 0 | IN | GPIO.28 | 28 | 20 |
| | | 0v | | | 39 || 40 | 0 | IN | GPIO.29 | 29 | 21 |
+-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
| BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM |
+-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
Changelog
0.3.2 (2017-11-29)
- (Homoran) fixed Mem available readings on Stretch
0.3.1 (2017-01-11)
- (olifre) Fixup swap_used calculation.
0.2.2 (2016-12-01)
- (bluefox) Add GPIO direction indication
0.2.2 (2016-11-22)
- (bluefox) Use BCM enumeration
0.2.1 (2016-10-29)
- (bluefox) fix start of adapter
0.2.0 (2016-10-23)
- (bluefox) just version change
0.1.1 (2016-10-13)
- (bluefox) implement GPIOs control
0.0.4 (2016-03-25)
- (bluefox) Try catch by eval (bluefox) do not process if exec fails
0.0.3 (2015-12-28)
- (husky-koglhof) Fixed value calc. Set Value to 2 digits
0.0.2 (2015-12-26)
- (husky-koglhof) Workaround for node 0.10.x
- (bluefox) Some Fixes
0.0.1 (2015-12-23)
- Initial commit. Alpha Version.
License
Copyright (c) 2015-2016 husky-koglhof husky.koglhof@icloud.com
MIT License