DreadfulCode / picberry

PIC Programmer using GPIO connector

picberry

PIC Programmer using GPIO connector

Copyright 2017 Francesco Valla

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.

Overview

picberry is a PIC programmer using GPIOs that doesn't require additional programming hardware.

It theorically supports dsPIC33E/PIC24E, dsPIC33F/PIC24H, PIC24FJ, PIC18FxxJxx, PIC32MX, PIC32MZ and PIC32MK families, but only some PICs have been tested.

Supported hosts

Currently picberry has support for the following host boards/processors:

• the Raspberry Pi
• Allwinner A10-based boards (like the Cubieboard)
• TI AM335x-based boards (like the Beaglebone Black or the AM3359 ICEv2).

Support for additional boards and processors can be easily added, providing the following macro in a header file inside the hosts folder:

/* GPIO registers address */
#define GPIO_BASE		// base address for the GPIO controller
#define BLOCK_SIZE		// size of the GPIO bank
#define PORTOFFSET		// port offset for letter-defined gpios

/* GPIO setup macros */
#define GPIO_IN(g)		// set gpio g as input
#define GPIO_OUT(g)		// set gpio g as output
#define GPIO_SET(g)		// set gpio g as high
#define GPIO_CLR(g)		// set gpio g as low
#define GPIO_LEV(g)		// read level of gpio g

/* default GPIO <-> PIC connections */
#define DEFAULT_PIC_CLK		// default gpio for PGC line
#define DEFAULT_PIC_DATA	// default gpio for PGD line
#define DEFAULT_PIC_MCLR	// default gpio for MCLR line

A build rule inside the Makefile for the specific platform has to be added too.

Building and Installing picberry

picberry is written using C++11 features, so it requires at least g++ version 4.7.

To build picberry launch make TARGET, where TARGET can be one of the following:

TARGET	Processor/Board
raspberrypi	Raspberry Pi v1 or Zero
raspberrypi2	Raspberry Pi v2 or v3
am335x	Boards based on TI AM335x (BeagleBone)
a10	Boards based on Allwinner A10 (Cubieboard)

Then launch sudo make install to install it to /usr/bin.

To change destination prefix use PREFIX=, e.g. sudo make install PREFIX=/usr/local.

For cross-compilation, given that you have the required cross toolchain in you PATH, simply export the CROSS_COMPILE variable before launching make, e.g. CROSS_COMPILE=arm-linux-gnueabihf- make raspberrypi2.

Using picberry

picberry [options]

Programming Options

-h                print help
-g PGC,PGD,MCLR   GPIO selection in form PORT:NUM, default if not present
-S port			  server mode, listening on given port                
-f family		  PIC family (dspic33e, dspic33f, pic18fj, pic32mx1, pic32mx2, pic32mx3, pic32mz)
-i file           input file
-o file           output file (default: ofile.hex)

-r                read chip
-w                bulk erase and write chip
-e                bulk erase chip
-b                blank check of the chip
-d                read configuration registers

--noverify        skip memory verification after programming
--debug           turn ON debug

Runtime Options

   -R                reset

For Example, to connect the PIC to RPi GPIOs 11 (PGC), 9 (PGD), 22 (MCLR) and write on a dsPIC33FJ128GP802 the file fw.hex:

picberry -w -g 11,9,22 -f dspic33f -i fw.hex

To connect the PIC to A10 GPIOs B15 (PGC), B17 (PGD), I15 (MCLR):

picberry -w -g B:15,B:17,I:15 -f dspic33f -i fw.hex

Programming Hardware

To use picberry you will need only the "recommended minimum connections" outlined in each PIC datasheet.

Between PIC and the SoC you must have the four basic ICSP lines: PGC (clock), PGD (data), MCLR (Reset), GND. You can also connect PIC VDD line to target board 3v3 line, but be careful: such pins normally have low current capabilities, so consider your circuit current drawn!

If not specified in the command line, the default GPIOs <-> PIC connections are the following:

for the Raspberry Pi:

PGC  <-> GPIO23
PGD  <-> GPIO24
MCLR <-> GPIO18

for the Allwinner A10:

PGC  <-> PB15
PGD  <-> PB17
MCLR <-> PB12

for AM335x:

PGC  <-> GPIO12
PGD  <-> GPIO13
MCLR <-> GPIO40

Remote GUI

Remote GUI is written in Qt5 and allows to control a picberry session running in server mode (that is, launched with the -S <port> command line argument).

To compile it, just launch qmake and then make in the remote_gui folder.

References

• dsPIC33E/PIC24E Flash Programming Specification
• dsPIC33F/PIC24H Flash Programming Specification
• PIC24FJ Flash Programming Specification
• PIC24FJXXGA0XX Flash Programming Specification
• PIC24FJXXXDA1/DA2/GB2/GA3/GC0 Families Flash Programming Specification
• PIC10(L)F320/322 Flash Programming Specification
• PIC12(L)F1822/PIC16(L)F182X Flash Programming Specification
• PIC18F2XJXX/4XJXX Family Programming Specification
• PIC32 Flash Programming Specification

Licensing

picberry is released under the GPLv3 license; for full license see the LICENSE file.

The Microchip name and logo, PIC, In-Circuit Serial Programming, ICSP are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

Raspberry Pi is a trademark of The Raspberry Pi Foundation.