The Salad Fork is a Voron Trident scaled down to use 1515 aluminum extrusions for the frame instead of 2020, exactly like how the Micron is a Voron 2.4 scaled down. It is not a modification for a Voron V0, but a from-scratch build that requires longer extrusions and rails, two more V0.1 integrated-leadscrew Z motors, a higher-wattage power supply, possibly a bigger bed…
Why go to the trouble of a whole new build? Well, Salad Fork features:
Coming soon™…
The latest official BOM is available on Google Sheets. The information below may not be complete; last updated November 17, 2021.
Frame (120mm³ build volume)
| Component |
Quantity |
Notes |
| HFS3-1515-400 |
4 |
Cross-drill 7.5mm from both ends, plus drill 1× gantry hole each per drill guide |
| HFS3-1515-270 |
6 |
Tap both ends |
| HFS3-1515-240 |
5 |
Tap both ends, cross-drill 2 extrusions at center |
| HFS3-1515-230 |
1 |
Tap one end |
| HFS3-1515-210 |
1 |
|
| HFS3-1515-145 |
1 |
|
| HFS3-1515-140 |
1 |
Tap one end |
Frame (150mm³ build volume)
| Component |
Quantity |
Notes |
| HFS3-1515-400 |
4 |
Cross-drill 7.5mm from both ends, plus drill 1× gantry hole each per drill guide |
| HFS3-1515-300 |
6 |
Tap both ends |
| HFS3-1515-270 |
5 |
Tap both ends, cross-drill 2 extrusions at center |
| HSF3-1515-240 |
1 |
Tap one end |
| HSF3-1515-230 |
1 |
|
| HFS3-1515-175 |
1 |
|
| HSF3-1515-170 |
1 |
Tap one end |
Fasteners
| Component |
Quantity |
| M2x6 BHCS |
24 |
| M2x10 self-tapping |
4 |
| M2x12 SHCS |
8 |
| M3x6 BHCS |
49 |
| M3x6 SHCS |
10 |
| M3x8 BHCS |
41 |
| M3x8 SHCS |
8 |
| M3x10 BHCS |
40 |
| M3x12 BHCS |
4 |
| M3x12 SHCS |
18 |
| M3x16 SHCS |
3 |
| M3x20 SHCS |
6 |
| M3x25 BHCS |
18 |
| M3x25 SHCS |
6 |
| M3x30 BHCS |
2 |
| M3x35 BHCS |
5 |
| M3x35 SHCS |
4 |
| M5x16 BHCS |
3 |
| M3 Heatset |
30 |
| M3 Washer |
26 |
| M3 lock nut |
6 |
| M3 hex nut |
98 |
| M4 knurled nut |
3 |
| M5 hex nut |
3 |
| 6x3 neodymium magnet |
8 |
Motion
| Component |
Quantity |
| NEMA14 stepper |
2 |
| NEMA17 integrated-leadscrew stepper |
3 |
| MGN9C 180 |
1 (for 120mm³) |
| MGN7H 200 |
5 (for 120mm³) |
| MGN9C 210 |
1 (for 150mm³) |
| MGN7H 230 |
2 (for 150mm³) |
| MGN7H 200 |
3 (for 150mm³) |
| Gates GT2 6mm open belt |
4m |
| F623-RS flanged bearings |
24 |
| GE5C spherical bearings |
3 |
| D2F switch |
4 |
| TR8×8 leadscrew nut |
3 |
| Rubber foot |
4 |
Electronics
| Component |
Quantity |
Notes |
| Control board |
1 |
Fysetc Spider or BigTreeTech Octopus |
| TMC 2209 driver |
6 |
|
| Raspberry Pi |
1 |
The Klipper host |
| C13 power cable |
1 |
|
| Meanwell UHP-200-24 |
1 |
|
| Keenovo 100mm² 60W 24V heater |
1 |
DC bed heater, 120mm³ build |
| Keenovo 120mm² 120W 24V heater |
1 |
DC bed heater, 150mm³ build |
| Keenovo 100mm² 60W 120/240V heater |
1 |
AC bed heater, 120mm³ build |
| Keenovo 120mm² 120W 120/240V heater |
1 |
AC bed heater, 150mm³ build |
| AC SSR (Omron G3NA-210B-UTU DC5-24, Panasonic AQA211VL) |
1 |
for AC bed heater |
Toolhead
| Component |
Quantity |
Notes |
| NEMA14 pancake stepper |
1 |
|
| BMG gear set |
1 |
|
| 3010 axial fan |
1 |
Only for Dragonfly BMS hotend |
| 3007 axial fan |
1 |
All other hotends |
| 3010 blower fan |
2 |
|
| Hotend |
1 |
|
