You can download latest build with artifacts from GitHub Releases page

GyverLampCpp

Rewrite of https://github.com/AlexGyver/GyverLamp in C++ and classes for PlatformIO: https://platformio.org/platformio-ide

Contact

Discuss building, modifications, deployment, etc. in telegram group: @GyverLampCpp

Content

Contains effects ported from:

Contains DMX core ported from:

https://github.com/Aircoookie/WLED

All original code is owned by it's authors

Supported boards

esp8266 with 4MB flash. Environment name - nodemcu
esp-01s board woth 1MB flash. Environment name - esp01s
Sonoff (Basic) board with 1MB flash. Environment name - sonoff-r1
Sonoff (Basic) board with 4MB flash. Environment name - sonoff-r1-4m
Any ESP32 board. Environment name - esp32dev

Note: 1MB boards are not capable of OTA firmware updates

How to build

build firmware: pio run -e nodemcu
build filesystem: pio run --target buildfs -e nodemcu

Filesystem build

Easy steps:

grab data.zip from latest release (https://github.com/CODeRUS/GyverLampCpp/releases)
extract archive to project's root folder
build the filesystem in Platform IO

Manual steps:

build https://github.com/CODeRUS/led-lamp-webui
build https://github.com/CODeRUS/wifimanager-react-page
copy gzipped artifacts without folder structure to data folder
build filesystem in Platform IO

PLEASE! Do not forget to build or to download and extract data artifacts from releases page! It is not present in git repository!

Then just upload built fs to module using pio run --target uploadfs -e nodemcu

Configuration

src/EffectsManager.cpp - comment out unused effects here. Comment out incudes at top and RegisterEffect from bottom of file.

data/effects.json - default options for effects

i - id of effect, should match one in src/EffectsManager.cpp
n - name of eefect visible in ui and Home Assistant
s - effect speed
l - effect scale
b - effect brightness

data/settings.json - main settings of firmware matrix - settings of matrix

pin - GPIO number of pin used to communicate with matrix leds
type - match with Framebuffer GFX: https://github.com/marcmerlin/Framebuffer_GFX/blob/master/Framebuffer_GFX.h#L43
values should be combined. Example: NEO_MATRIX_ZIGZAG + NEO_MATRIX_BOTTOM + NEO_MATRIX_RIGHT + NEO_MATRIX_ROWS (or NEO_MATRIX_COLUMNS) = 11 (or 15). Matrix test effect at boot: Pixels started from left bottom. Red is horizontal from left to right, Green is vertical from bottom to top.
rotation - value from 0 to 3, each value by +90 degree.
dither - enable or disable dithering: https://github.com/FastLED/FastLED/wiki/FastLED-Temporal-Dithering
order - pixel order for leds. use lowercase 3 letters: "rgb", "grb" or similar

connection - connection settings

mdns - domain name in .local
apName - access point name for initial configuration
apPassword - access point password
ntpServer - time server name
ntpOffset - time offset in seconds
hostname - hostname for local network
ssid - name of wifi network to connect
bssid - mac of wifi network, use for connection to certain access point
password - password of wifi network to connect
login - login for connection to wifi network (WPA-E)

mqtt - mqtt settings

host - server address
port - server port
username - username
password - password
uniqueId - unique identifier for entity light in Home Assistant
name - device name in Home Assistant
model - model name in Home Assistant

button - button settings

pin - GPIO pin number, set to 255 if you have no button connected
type - 1 if pin button is connected to 3v3, 0 if button connected to GND
state - set to 1 to invert button state, 0 for normal operation

Please refer to https://github.com/esp8266/Arduino/blob/master/variants/nodemcu/pins_arduino.h#L40 for pin numbers if using nodemcu-like ESP8266 boards! This configuration uses numeric gpio pins, not the ones marked as D0-D10 on the board!

Safe mode

If lamp is turned on while button is pressed, it will boot into safe mode. Lamp will try to connect to last known network, otherwise it will create access point. You can connect to lamp with your mobile device using wifi and upload correct json settings or firmware files.

Please do not use GPIO0, GPIO2, GPIO15 (D3, D4 and D8 on nodemcu boards) for button connection, your board may fail to boot at all if button will be pressed during startup: https://www.forward.com.au/pfod/ESP8266/GPIOpins/index.html

OTA - Over The Air updates

You can upload firmware.bin, fs.bin, settings.json, effects.json with OTA using web interface.

NOTE: Boards with 1MB flash memory (see Supported boards) don't have enough space for firmware/fs updates, but capable of json configuration updates

Changes with original GyverLamp projects

Rewritten in C++ and classes for easier maintenance
ESP32 support
Sonoff Basic support
Asynchronous WiFi Manager
FastLED_NeoMatrix library instead of Gyver handmade one (sorry)
Settings moved to SPIFFS json file

New features:

Clock effects
Spectrometer effect (requires microphone module or aux, should be uncommented in EffectsManager.cpp and added to effects.json)
React wifi manager self-coded component
React web with controls self-coded component. No need to install client applications
Firmware update page, allowing to upload firmware bin, filesystem bin or settings json
MQTT for Home Assistant integration
Sonoff Basic relay and led are bound to led state
DMX input via e131 and Art-Net protocols

Missing features from original project

Not compatible with any client application. You can connect to lamp directly using any web browser. Or use MQTT/HomeAssistant to control it
Alarms not implemented

TODO

Alarms support

Audio input wirings for Spectrometer effects

Please check by link: https://gist.github.com/CODeRUS/f025fa5c12d6eaad6878576e8255913a

Troubleshooting

If you have any issues with firmware or effects and you cannot find answers here check the closed issues on Github Issues page or leave message in Telegram Group

The effect start flickering

Try to disable dithering in settings.json set dither to false
Try to upload settings.json file via OTA updates

CODeRUS / GyverLampCpp