Commands to correlate 'apt' versions (such as 2.1.1) to Duet internal firmware nomenclature (such as "V3.01 RC5")
cd
git clone https://github.com/AndyEveritt/DuetVersions
- By default shows highest available, installed, and dependencies for installed, and reprapfirmware internal version for installed, version of duetcontrolframework.
- Specify a number as a command line argument to see same info for that many lines 'backward' from highest available duetcontrolframework.
Example:
./DuetVersion.sh 22
Highest Available DuetSoftwareFramework = 2.1.1
Currently Installed DuetSoftwareFramework = 2.1.1
Command line arg specified to request Release -22 from highest available.
Highest-22 is DuetSoftwareFramework = 1.0.4.1
Dependencies for DSF version 1.0.4.1 are:
duetcontrolserver (= 1.0.4.1)
duetsd (= 1.0.3)
duettools (= 1.0.4.1)
duetwebserver (= 1.1.1.0)
duetwebcontrol (= 2.0.0-5)
reprapfirmware (>= 1.0.4.1-1)
reprapfirmware (<= 1.0.4.1-999) )
reprapfirmware apt version 1.0.4.1-1 is internal version 3.0beta10+1
- Shows version and associated reprapfirmware internal version, for all duetsoftwareframework packages available on your feed(s). See https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Software_Installation for more information
Example:
./DuetVersionsAll.sh
Expect this to take several seconds per line of output.
duetsoftwareframework 2.1.1 contains reprapfirmware version 2.1.1-1 which is internal version 3.01-RC10
duetsoftwareframework 2.1.0 contains reprapfirmware version 2.1.0-1 which is internal version 3.01-RC9
duetsoftwareframework 2.0.0 contains reprapfirmware version 2.0.0-1 which is internal version 3.01-RC8
duetsoftwareframework 1.3.2 contains reprapfirmware version 1.3.2-1 which is internal version 3.01-RC7
duetsoftwareframework 1.3.1 contains reprapfirmware version 1.3.1-1 which is internal version 3.01-RC6
...snip...
- Shows commands that will install a 'back' or 'regressed' version of DSF and friends.
Example:
./DuetRegress.sh 2.1.0
Currently Installed duetsoftwareframework=2.1.2
Command line argument is requesting duetsoftwareframework=2.1.0
Which has associated reprapfirmware of 2.1.0-1 also known as 3.01-RC9
***********************************************************************************
* Note: The next step will run for a while; the script is (probably) not hung. *
***********************************************************************************
To regress to DSF version 2.1.0 which is RRF version 3.01-RC9:
1) Backup your files via:
mkdir ~/duetback
cp -r /opt/dsf/sd/* ~/duetback
or similar. Verify that the backup worked: 'ls ~/duetback' should show directories: 'filaments firmware gcodes macros sys' or similar.
2) Run this command: (it is long, be sure you get it all on one line)
sudo apt -y --allow-downgrades install duetsoftwareframework=2.1.0 duetcontrolserver=2.1.0 duetruntime=2.1.0 duetsd=1.0.6 duettools=2.1.0 duetwebcontrol=2.1.4 duetwebserver=2.1.0 reprapfirmware=2.1.0-1
3) Verify system is running properly, web interface opens, etc
4) If Pi runs, but won't connect to Duet Board, bossa the board
with the file found at /opt/dsf/sd/sys/Duet3Firmware_MB6HC.bin
Instructions here:
https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Updating_Duet_3_main_board_firmware
5) Check files like config.g, macros, etc, and restore as required.