AlexanderKa1/tinyproto

Introduction
Key Features
Supported platforms
Easy to use
Setting up
How to buid
Using tiny_loopback tool
License

Introduction

Tiny Protocol is layer 2 protocol. It is intended to be used for the systems with low resources. It is also can be compiled for desktop Linux system, and it can be built it for Windows. Using this library you can easy implement data transfer between 2 microcontrollers or between microcontroller and pc via UART, SPI, I2C or any other communication channels. You don't need to think about data synchronization between points. The library use no dynamic allocation of memory. TinyProto is based on RFC 1662, it implements the following frames:

U-frames (SABM, UA)
S-frames (REJ, RR)
I-frames

Key Features

Protocols, implemented by library:

hdlc framing (hdlc_xxxx API, basis for light, half-duplex and full-duplex implementations)
light (tiny_light_xxxx API, simplest API to use, doesn't support confirmation)
half-duplex (tiny_hd_xxxx API, lightweight implementation of protocol with frame confirmation)
full-duplex (tiny_fd_xxxx true RFC 1662 implementation, supports confirmation, frames retransmissions)

Main features:

Error detection (basic hdlc, hd and fd variants)
- Simple 8-bit checksum (sum of bytes)
- FCS16 (CCITT-16)
- FCS32 (CCITT-32)
Frames of maximum 32K or 2G size (limit depends on platform).
Low SRAM consumption (starts at 50 bytes).
Low Flash consumption (starts at 1KiB, features can be disabled and enabled at compilation time)
No dynamic memory allocation
Zero copy implementation (basic hdlc, light versions do not use copy operations)
Serial loopback tool for debug purposes and performance testing

Supported platforms

Any platform, where C/C++ compiler is available (C99, C++11)

Easy to use

Usage of light Tiny Protocol in C++ can look like this:

Tiny::ProtoLight  proto;
Tiny::Packet<256> packet;
...
    if (Serial.available()) {
        int len = proto.read( packet );
        if (len > 0) {
            /* Send message back */
            proto.write( packet );
        }
    }

Example of using full duplex Tiny Protocol in C++ is a little bit bigger, but it is still simple:

Tiny::ProtoFd<FD_MIN_BUF_SIZE(64,4)>  proto;

void onReceive(Tiny::IPacket &pkt) {
    if ( proto.write(pkt) == TINY_ERR_TIMEOUT ) {
        // Do what you need to do if looping back failed on timeout.
        // But never use blocking operations inside callback
    }
}
...
proto.setReceiveCallback( onReceive );
...
void loop() {
    if (Serial.available()) {
        proto.run_rx();
    }
    proto.run_tx();
}

How to build

Linux

make
# === OR ===
mkdir build
cd build
cmake -DEXAMPLES=ON ..
make

Windows

mkdir build
cd build
cmake -G "Visual Studio 16 2019" -DEXAMPLES=ON ..

Setting up

Arduino Option 1 (with docs and tools)
- Download source from https://github.com/lexus2k/tinyproto
- Put the downloaded library content to Arduino/libraries/tinyproto folder
- Restart the Arduino IDE
- You will find the examples in the Arduino IDE under File->Examples->tinyproto
Arduino Option 2 (only library without docs)
- Go to Arduino Library manager
- Find and install tinyproto library
- Restart the Arduino IDE
- You will find the examples in the Arduino IDE under File->Examples->tinyproto
ESP32 IDF
- Download sources from https://github.com/lexus2k/tinyproto and put to components folder of your project
- Run make for your project
Linux
- Download sources from https://github.com/lexus2k/tinyproto
- Run make command from tinyproto folder, and it will build library and tools for you
Plain AVR
- Download sources from https://github.com/lexus2k/tinyproto
- Install avr gcc compilers
- Run make ARCH=avr

Using tiny_loopback tool

Connect your Arduino board to PC
Run your sketch or tinylight_loopback
Compile tiny_loopback tool
Run tiny_loopback tool: ./bld/tiny_loopback -p /dev/ttyUSB0 -t light -g -c 8 -a -r
Connect your Arduino board to PC
Run your sketch or tinyhd_loopback
Compile tiny_loopback tool
Run tiny_loopback tool: ./bld/tiny_loopback -p /dev/ttyUSB0 -t hd -c 8 -g -a -r
Connect your Arduino board to PC
Run your sketch or tinyfd_loopback
Compile tiny_loopback tool
Run tiny_loopback tool: ./bld/tiny_loopback -p /dev/ttyUSB0 -t fd -c 8 -w 3 -g -a -r

For more information about this library, please, visit https://github.com/lexus2k/tinyproto. Doxygen documentation can be found at Codedocs xyz site. If you found any problem or have any idea, please, report to Issues section.

License

This file is part of Tiny Protocol Library.

Protocol Library is free software: you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

Protocol Library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with Protocol Library. If not, see http://www.gnu.org/licenses/.

AlexanderKa1 / tinyproto