Arduboy homemade package

Arduino IDE board package for Arduboy and homemade versions with the following advantages:

Single install
Includes all Arduboy libraries with support for alternate displays and wiring
Includes Arduboy optimized Arduino core with extra features and space savings
Cathy3K bootloader support

To install the package:

Start Arduino IDE and press CTRL + comma to select properties.
Copy and paste the URL below in Additional Boards Manager URLs: text box and click on OK

https://raw.githubusercontent.com/MrBlinky/Arduboy-homemade-package/master/package_arduboy_homemade_index.json

After this:

Go to Tools > Boards > Board manager
In the text box type homemade or Arduboy homemade
Click on the Arduboy Homemade package and click the Install button.

You can now select Arduboy, Arduboy DevKit and Homemade Arduboy boards from the Tools menu.

Libraries

This package contains all the currently available Arduboy libraries with changes for homemade Arduboys. If Arduboy libraries were installed manually, it is recommended to uninstall them.

Pin wiring table

Arduboy function	Arduboy Leonardo/Micro	DevelopmentKit	ProMicro 5V (standard wiring)	ProMicro 5V (alternate wiring)
OLED CS	12 PORTD6	6 PORTD7	GND****	1/TXO PORTD3*
OLED DC	4 PORTD4	4 PORTD4	4 PORTD4	4 PORTD4
OLED RST	6 PORTD7	12 PORTD6	6 PORTD7	2 PORTD1*
SPI SCK	15 PORTB1	15 PORTB1	15 PORTB 1	15 PORTB1
SPI MOSI	16 PORTB2	16 PORTB2	16 PORTB2	16 PORTB2
RGB LED RED	10 PORTB6	_	10 PORTB6	10 PORTB6
RGB LED GREEN	11 PORTB7	_	-	3 PORTD0*
RGB LED BLUE	9 PORTB5	17 PORTB0	9 PORTB5	9 PORTB5
RxLED	17 PORTB0	_	17 PORTB0	17 PORTB0
TxLED	30 PORTD5	_	30 PORTD5	30 PORTD5
BUTTON UP	A0 PORTF7	8 PORTB4	A0 PORTF7	A0 PORTF7
BUTTON RIGHT	A1 PORTF6	5 PORTC6	A1 PORTF6	A1 PORTF6
BUTTON LEFT	A2 PORTF5	9 PORTB5	A2 PORTF5	A2 PORTF5
BUTTON DOWN	A3 PORTF4	10 PORTB6	A3 PORTF4	A3 PORTF4
BUTTON A (left)	7 PORTE6	A0 PORTF7	7 PORTE6	7 PORTE6
BUTTON B (right)	8 PORTB4	A1 PORTF6	8 PORTB4	8 PORTB4
SPEAKER PIN 1	5 PORTC6	A2 PORTF5	5 PORTC6	5 PORTC6
SPEAKER PIN 2	13 PORTC7	A3 PORTF4**	GND	6 PORTD7*
-----------------	----------------------	-----------	----------------------------------	---------------------------------
CART_CS	0 PORTD2***	-	-	0 PORTD2***
SPI MISO	14 PORTB3***	-	-	14 PORTB3***

Numbers before the portnames are Arduino assigned pin numbers.

(*) Pro Micro alternate wiring pins:

PORTD3 OLED CS
PORTD1 OLED RST
PORTD7 SPEAKER 2
PORTD0 RGB LED GREEN

(**) speaker pin 2 output is connected to speaker pin 1 on DevKit hardware. To prevent the IO pins from possible damage, speaker pin 2 should NOT be configured as an output.

(***) Flash cart support:

0 PORTD2 flash cart chip select
14 PORTB3 flash cart data in (MISO)

(****) When using serial flash with the Pro Micro standard wiring, OLED_CS (chip select) cannot be grounded (always active). In this case a simple circuit with a general purpose PNP transistor and two resistors can be used to deactive OLED_CS while CART_CS is active.

TODO add schematic

(future) expansion connector

An expansion connector can be added to a modified or Homemade Arduboy in the form of a 12 pin male header with 0.1"pitch. which can be used for:

ICSP header for easy in circuit programming (updating bootloader)
flash cart slot
SD card adapter
infrared communications
multiplayer link
sensors

Expansion connector pinout

( (Homemade) Arduboy facing top - front view female pinheader)

12	11	10	9	8	7	6	5	4	3	2	1
TX	RX	SCL	SDA	NC	KEY	MISO	MOSI	CLK	RST	GND	Vcc

TX*  - Serial Transmitter output
RX   - Serial Receiver input / Flash cart chip select
SCL* - I2C/TWI serial clock I/O
SDA* - I2C/TWI serial data I/O
NC   - Not connected (reserved for future use)
KEY  - Key pin. should be filled to block pin insertion (reverse insert protection)
MISO - SPI/ICSP Master Input, Slave Output
MOSI - SPI/ICSP Master Output, Slave Input
CLK  - SPI/ICSP clock
RST  - MCU/ICSP reset
GND  - Ground (0V)
Vcc  - 5V (~3.0V to ~4.1V on Arduboy)
(*) Not available when using Pro Micro with Alternate Wiring

tonym128 / Arduboy-homemade-package