Giters
rusefi
/
hellen154hyundai
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
Watchers:
6
Issues:
156
Forks:
2
rusefi/hellen154hyundai Issues
Standard LUA script no longer fits on F4
Updated
4 days ago
F7 H154 fan broken again
Updated
a month ago
Comments count
8
AEM wideband reading unstable on RevE over CAN
Updated
a month ago
Comments count
1
Selected engine sync input not configured
Closed
a month ago
Comments count
5
Lua not writeable
Closed
a month ago
Cannot save trigger input PIN setting on H154 F7
Closed
a month ago
Forced CRITICAL error due to TPS2 on F7. Did TPS2 change between F4 and F7?
Closed
a month ago
Comments count
1
K22 BK2 Wastegate position does not show under Wastegate and Idle Position sensors
Closed
3 months ago
rev E fab
Updated
3 months ago
Comments count
5
Figure out wideband present ONLY ON BK2
Updated
3 months ago
Comments count
11
RevC not reading PPS2
Updated
3 months ago
Comments count
10
Need to disable onboard WBO2
Updated
4 months ago
rev D pps2
Closed
4 months ago
Comments count
2
rev C PPS2 voltage
Closed
4 months ago
Comments count
4
Crank/Cam choices do not show revD option
Closed
4 months ago
Since revD is ONLY F7, should any revC and before options be removed from F7 build?
Updated
4 months ago
Comments count
1
Assigning injector outputs causes FATAL on revD
Closed
4 months ago
Comments count
2
Rename ECU pin 38 to "BK1 o2 narrow signal" and route to analog input
Closed
4 months ago
C67 trace name "CPSV EVAP Purge"
Closed
4 months ago
Rename ECU pin 93 to "Heater control"
Closed
4 months ago
Comments count
1
C67 CPSV needs to be controlled to not have issues with fuel tank depressurization
Closed
4 months ago
Comments count
6
Connect pin 38 to an available analog input (if available)
Closed
5 months ago
Comments count
1
Radiator Fans not engaging, all settings seem correct? 20240405 RevC
Closed
5 months ago
Comments count
1
rev c: uneven R from CAM to +5v
Closed
6 months ago
Comments count
5
Rev-D changelist
Updated
6 months ago
WBO module: 2x3 molex and maybe OEM header as well
Closed
6 months ago
Comments count
3
aux connector silk on both sides
Closed
6 months ago
Comments count
1
Улучшить схему
Closed
6 months ago
Comments count
3
let's use 33810 for injectors and coils
Closed
6 months ago
Comments count
1
H-bridge SPI
Closed
6 months ago
Comments count
1
reorder rev C
Closed
7 months ago
Comments count
1
four connector holes
Closed
7 months ago
Comments count
4
re-fab rev C
Closed
7 months ago
Comments count
3
reorder rev C
Closed
7 months ago
F4 top of the line would it be an option?
Closed
7 months ago
Comments count
4
bump mm-mcu version to get extra readability
Closed
7 months ago
X9 Digital 1 as Flex Fuel input shows 0% with 60hz PU/PD fix
Closed
7 months ago
Comments count
13
Blue comment "used by Kia Forte" comment on tach output wire
Closed
7 months ago
Comments count
6
F7 by default
Closed
7 months ago
Switch to F7 processor
Closed
7 months ago
Comments count
1
aux connector pinout silk on back side
Closed
7 months ago
Comments count
1
Aux LS1, X8 not working
Closed
10 months ago
Comments count
3
X9 not choosable under Other Sensor Inputs
Closed
10 months ago
X10 not choosable for MAP input
Closed
10 months ago
Comments count
1
Hyundai Genesis "Couple"
Closed
10 months ago
23.9-2 board
Updated
a year ago
benc test VSS brake A/C request
Updated
a year ago
Comments count
3
Possible user error led to smoke
Closed
a year ago
Comments count
8
Smiley face "Daniel" board now "3.6-1"
Closed
a year ago
Comments count
3
Sometimes ETB calibration fails even though it works with a preloaded map; why does this happen?
Closed
a year ago
Comments count
1
Previous
Next