Giters
kanflo
/
opendps
Give your DPS5005 the upgrade it deserves
Geek Repo:
Geek Repo
Github PK Tool:
Github PK Tool
Stargazers:
867
Watchers:
64
Issues:
144
Forks:
126
kanflo/opendps Issues
Force Voltage calibration line of best fits to pass through (0, 0)
Closed
5 years ago
Comments count
12
esp8266 proxy Arduino variant
Updated
5 years ago
Comments count
7
Voltage is off
Updated
5 years ago
Comments count
18
Measure output power and energy
Updated
5 years ago
Comments count
4
dpsctl library
Updated
5 years ago
Comments count
1
DPS5015 Overcurrent Protection Error
Closed
5 years ago
Comments count
4
Support for DPS3003
Updated
3 years ago
Comments count
16
Implement IWDG for safety, and new device support
Updated
5 years ago
Comments count
1
Not working with DPS3005 and OpenOCD 0.10.0 (20190423)
Closed
5 years ago
Comments count
11
esp8266-proxy build: use option -std=c99 or -std=gnu99 to compile your code
Closed
5 years ago
Comments count
2
dpsctl.py working only for some commands
Closed
5 years ago
Comments count
3
Possible race condition ?
Closed
5 years ago
Comments count
1
Change ESP8266 proxy to use TCP instead of UDP
Updated
5 years ago
Comments count
7
DPS5015 Current Value only 9.999
Closed
4 years ago
Comments count
2
Cannot flash over system gpio on Raspberry Pi 3?
Closed
5 years ago
Add baud rate limit to documentation
Updated
5 years ago
Comments count
1
Error upgrading oder UART | AttributeError: 'bytes' object has no attribute 'encode'
Closed
5 years ago
Comments count
5
Add compile time flag for disabling CV screen
Updated
2 years ago
Comments count
2
DPS5005 black screen when firmware is compiled with gcc 7.3.0
Updated
5 years ago
Comments count
3
Add calibration routine information to README
Updated
5 years ago
Comments count
4
Improve calibration gradient detection algorithm
Updated
5 years ago
Comments count
2
Powering off DPS in the calibration routine causes it to fail
Closed
5 years ago
Comments count
1
Implement crash dump
Updated
5 years ago
Now redundant start up current ADC zeroing
Updated
3 years ago
Comments count
10
Implement a quiet mode in dpsctl.py for communicate()
Closed
5 years ago
Is there any way to make power-state persist across resets?
Updated
5 years ago
Comments count
8
cannot set voltage remotely via serial port
Closed
5 years ago
Comments count
4
Overvoltage limit in CV?
Closed
5 years ago
Comments count
3
Variables should be volatile
Closed
5 years ago
Extend ocd-client.py to fetch factory programmed calibration coefficients
Updated
5 years ago
Comments count
7
Changing between screens does not clear the previous screen
Updated
5 years ago
Comments count
2
DPS5005 v2.3 Voltage Offset
Closed
5 years ago
Comments count
2
Calibration/Debug Screen
Closed
5 years ago
Comments count
16
ADC interrupt improvement
Closed
5 years ago
Comments count
1
Issuing a lot of calibration coefficients at once fails
Updated
5 years ago
Comments count
2
DPS5005 Brick
Closed
5 years ago
Comments count
11
Graphing screen
Updated
5 years ago
Comments count
2
ili9163c_draw_pixel x and y are wrong
Closed
5 years ago
Comments count
11
Test if glyphs and icons can be converted to 4bpp mono
Closed
5 years ago
Comments count
13
Merge gfx-convert.sh and generate_font.py
Closed
5 years ago
Comments count
1
Allow fonts of arbitrary sizes
Closed
5 years ago
Comments count
1
Need a debounce on buttons
Closed
5 years ago
Comments count
7
Missing break;
Closed
5 years ago
Comments count
1
Python dpsctl incompatibility with windows
Closed
5 years ago
number_draw() could be improved to handle any font
Closed
5 years ago
Comments count
2
Missing input voltage on display
Closed
5 years ago
Can set output voltage higher than possible output
Closed
5 years ago
Comments count
1
Python get GIT hashes
Closed
5 years ago
DPS8005 Support
Updated
a year ago
Comments count
33
No way to disable dbg_printf from makefile
Closed
5 years ago
Comments count
1
Previous
Next