Some Weird Issues with ESP32-S3-WROOM-1-N8R8 on a Customized Board. Error Messages Popped Up After Unplugging and Plugging the USB Cord
zyan003 opened this issue · comments
Board
Wareshare ESP32-S3-Touch-LCD-7
Device Description
Wareshare ESP32-S3-Touch-LCD-7 with ESP32-S3-WROOM-1-N8R8 on board.
Hardware Configuration
/*
* SPDX-FileCopyrightText: 2023-2024 Espressif Systems (Shanghai) CO LTD
*
* SPDX-License-Identifier: Apache-2.0
*/
#pragma once
// *INDENT-OFF*
/* Set to 1 if using a custom board */
#define ESP_PANEL_USE_CUSTOM_BOARD (1) // 0/1
#if ESP_PANEL_USE_CUSTOM_BOARD
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
//////////////////////////// Please update the following macros to configure the LCD panel /////////////////////////////
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/* Set to 1 when using an LCD panel */
#define ESP_PANEL_USE_LCD (1) // 0/1
#if ESP_PANEL_USE_LCD
/**
* LCD Controller Name. Choose one of the following:
* - GC9A01, GC9B71, GC9503
* - ILI9341
* - NV3022B
* - SH8601
* - SPD2010
* - ST7262, ST7701, ST7789, ST7796, ST77916, ST77922
*/
#define ESP_PANEL_LCD_NAME ST7262
/* LCD resolution in pixels */
#define ESP_PANEL_LCD_WIDTH (800)
#define ESP_PANEL_LCD_HEIGHT (480)
/* LCD Bus Settings */
/**
* If set to 1, the bus will skip to initialize the corresponding host. Users need to initialize the host in advance.
* It is useful if other devices use the same host. Please ensure that the host is initialized only once.
*/
#define ESP_PANEL_LCD_BUS_SKIP_INIT_HOST (1) // 0/1
/**
* LCD Bus Type. Choose one of the following:
* - ESP_PANEL_BUS_TYPE_I2C (not ready)
* - ESP_PANEL_BUS_TYPE_SPI
* - ESP_PANEL_BUS_TYPE_QSPI
* - ESP_PANEL_BUS_TYPE_I80 (not ready)
* - ESP_PANEL_BUS_TYPE_RGB (only supported for ESP32-S3)
*/
#define ESP_PANEL_LCD_BUS_TYPE (ESP_PANEL_BUS_TYPE_RGB)
/**
* LCD Bus Parameters.
*
* Please refer to https://docs.espressif.com/projects/esp-idf/en/latest/esp32s3/api-reference/peripherals/lcd.html and
* https://docs.espressif.com/projects/esp-iot-solution/en/latest/display/lcd/index.html for more details.
*
*/
#if ESP_PANEL_LCD_BUS_TYPE == ESP_PANEL_BUS_TYPE_SPI
#define ESP_PANEL_LCD_BUS_HOST_ID (1) // Typically set to 1
#define ESP_PANEL_LCD_SPI_IO_CS (5)
#if !ESP_PANEL_LCD_BUS_SKIP_INIT_HOST
#define ESP_PANEL_LCD_SPI_IO_SCK (7)
#define ESP_PANEL_LCD_SPI_IO_MOSI (6)
#define ESP_PANEL_LCD_SPI_IO_MISO (-1) // -1 if not used
#endif
#define ESP_PANEL_LCD_SPI_IO_DC (4)
#define ESP_PANEL_LCD_SPI_MODE (0) // 0/1/2/3, typically set to 0
#define ESP_PANEL_LCD_SPI_CLK_HZ (40 * 1000 * 1000)
// Should be an integer divisor of 80M, typically set to 40M
#define ESP_PANEL_LCD_SPI_TRANS_QUEUE_SZ (10) // Typically set to 10
#define ESP_PANEL_LCD_SPI_CMD_BITS (8) // Typically set to 8
#define ESP_PANEL_LCD_SPI_PARAM_BITS (8) // Typically set to 8
#elif ESP_PANEL_LCD_BUS_TYPE == ESP_PANEL_BUS_TYPE_QSPI
#define ESP_PANEL_LCD_BUS_HOST_ID (1) // Typically set to 1
#define ESP_PANEL_LCD_SPI_IO_CS (5)
#if !ESP_PANEL_LCD_BUS_SKIP_INIT_HOST
#define ESP_PANEL_LCD_SPI_IO_SCK (9)
#define ESP_PANEL_LCD_SPI_IO_DATA0 (10)
#define ESP_PANEL_LCD_SPI_IO_DATA1 (11)
#define ESP_PANEL_LCD_SPI_IO_DATA2 (12)
#define ESP_PANEL_LCD_SPI_IO_DATA3 (13)
#endif
#define ESP_PANEL_LCD_SPI_MODE (0) // 0/1/2/3, typically set to 0
#define ESP_PANEL_LCD_SPI_CLK_HZ (40 * 1000 * 1000)
// Should be an integer divisor of 80M, typically set to 40M
#define ESP_PANEL_LCD_SPI_TRANS_QUEUE_SZ (10) // Typically set to 10
#define ESP_PANEL_LCD_SPI_CMD_BITS (32) // Typically set to 32
#define ESP_PANEL_LCD_SPI_PARAM_BITS (8) // Typically set to 8
#elif ESP_PANEL_LCD_BUS_TYPE == ESP_PANEL_BUS_TYPE_RGB
#define ESP_PANEL_LCD_RGB_CLK_HZ (14 * 1000 * 1000)
#define ESP_PANEL_LCD_RGB_HPW (4)
#define ESP_PANEL_LCD_RGB_HBP (8)
#define ESP_PANEL_LCD_RGB_HFP (8)
#define ESP_PANEL_LCD_RGB_VPW (4)
#define ESP_PANEL_LCD_RGB_VBP (8)
#define ESP_PANEL_LCD_RGB_VFP (8)
#define ESP_PANEL_LCD_RGB_PCLK_ACTIVE_NEG (0) // 0: rising edge, 1: falling edge
#define ESP_PANEL_LCD_RGB_DATA_WIDTH (16) // 8 | 16
#define ESP_PANEL_LCD_RGB_PIXEL_BITS (16) // 24 | 16
#define ESP_PANEL_LCD_RGB_FRAME_BUF_NUM (1) // 1/2/3
#define ESP_PANEL_LCD_RGB_BOUNCE_BUF_SIZE (0) // Bounce buffer size in bytes. This function is used to avoid screen drift.
// To enable the bounce buffer, set it to a non-zero value. Typically set to `ESP_PANEL_LCD_WIDTH * 10`
// The size of the Bounce Buffer must satisfy `width_of_lcd * height_of_lcd = size_of_buffer * N`,
// where N is an even number.
#define ESP_PANEL_LCD_RGB_IO_HSYNC (46)
#define ESP_PANEL_LCD_RGB_IO_VSYNC (3)
#define ESP_PANEL_LCD_RGB_IO_DE (5) // -1 if not used
#define ESP_PANEL_LCD_RGB_IO_PCLK (7)
#define ESP_PANEL_LCD_RGB_IO_DISP (-1) // -1 if not used
#define ESP_PANEL_LCD_RGB_IO_DATA0 (14)
#define ESP_PANEL_LCD_RGB_IO_DATA1 (38)
#define ESP_PANEL_LCD_RGB_IO_DATA2 (18)
#define ESP_PANEL_LCD_RGB_IO_DATA3 (17)
#define ESP_PANEL_LCD_RGB_IO_DATA4 (10)
#define ESP_PANEL_LCD_RGB_IO_DATA5 (39)
#define ESP_PANEL_LCD_RGB_IO_DATA6 (0)
#define ESP_PANEL_LCD_RGB_IO_DATA7 (45)
#if ESP_PANEL_LCD_RGB_DATA_WIDTH > 8
#define ESP_PANEL_LCD_RGB_IO_DATA8 (48)
#define ESP_PANEL_LCD_RGB_IO_DATA9 (47)
#define ESP_PANEL_LCD_RGB_IO_DATA10 (21)
#define ESP_PANEL_LCD_RGB_IO_DATA11 (1)
#define ESP_PANEL_LCD_RGB_IO_DATA12 (2)
#define ESP_PANEL_LCD_RGB_IO_DATA13 (42)
#define ESP_PANEL_LCD_RGB_IO_DATA14 (41)
#define ESP_PANEL_LCD_RGB_IO_DATA15 (40)
#endif
#if !ESP_PANEL_LCD_BUS_SKIP_INIT_HOST
#define ESP_PANEL_LCD_3WIRE_SPI_IO_CS (0)
#define ESP_PANEL_LCD_3WIRE_SPI_IO_SCK (1)
#define ESP_PANEL_LCD_3WIRE_SPI_IO_SDA (2)
#define ESP_PANEL_LCD_3WIRE_SPI_CS_USE_EXPNADER (0) // 0/1
#define ESP_PANEL_LCD_3WIRE_SPI_SCL_USE_EXPNADER (0) // 0/1
#define ESP_PANEL_LCD_3WIRE_SPI_SDA_USE_EXPNADER (0) // 0/1
#define ESP_PANEL_LCD_3WIRE_SPI_SCL_ACTIVE_EDGE (0) // 0: rising edge, 1: falling edge
#define ESP_PANEL_LCD_FLAGS_AUTO_DEL_PANEL_IO (0) // Delete the panel IO instance automatically if set to 1.
// If the 3-wire SPI pins are sharing other pins of the RGB interface to save GPIOs,
// Please set it to 1 to release the panel IO and its pins (except CS signal).
#define ESP_PANEL_LCD_FLAGS_MIRROR_BY_CMD (!ESP_PANEL_LCD_FLAGS_AUTO_DEL_PANEL_IO)
// The `mirror()` function will be implemented by LCD command if set to 1.
#endif
#else
#error "The function is not ready and will be implemented in the future."
#endif /* ESP_PANEL_LCD_BUS_TYPE */
/**
* LCD Venbdor Initialization Commands.
*
* Vendor specific initialization can be different between manufacturers, should consult the LCD supplier for
* initialization sequence code. Please uncomment and change the following macro definitions. Otherwise, the LCD driver
* will use the default initialization sequence code.
*
* There are two formats for the sequence code:
* 1. Raw data: {command, (uint8_t []){ data0, data1, ... }, data_size, delay_ms}
* 2. Formater: ESP_PANEL_LCD_CMD_WITH_8BIT_PARAM(delay_ms, command, { data0, data1, ... }) and
* ESP_PANEL_LCD_CMD_WITH_NONE_PARAM(delay_ms, command)
*/
// #define ESP_PANEL_LCD_VENDOR_INIT_CMD() \
// { \
// {0xFF, (uint8_t []){0x77, 0x01, 0x00, 0x00, 0x10}, 5, 0}, \
// {0xC0, (uint8_t []){0x3B, 0x00}, 2, 0}, \
// {0xC1, (uint8_t []){0x0D, 0x02}, 2, 0}, \
// {0x29, (uint8_t []){0x00}, 0, 120}, \
// or \
// ESP_PANEL_LCD_CMD_WITH_8BIT_PARAM(0, 0xFF, {0x77, 0x01, 0x00, 0x00, 0x10}), \
// ESP_PANEL_LCD_CMD_WITH_8BIT_PARAM(0, 0xC0, {0x3B, 0x00}), \
// ESP_PANEL_LCD_CMD_WITH_8BIT_PARAM(0, 0xC1, {0x0D, 0x02}), \
// ESP_PANEL_LCD_CMD_WITH_NONE_PARAM(120, 0x29), \
// }
/* LCD Color Settings */
/* LCD color depth in bits */
#define ESP_PANEL_LCD_COLOR_BITS (16) // 8/16/18/24
/*
* LCD RGB Element Order. Choose one of the following:
* - 0: RGB
* - 1: BGR
*/
#define ESP_PANEL_LCD_BGR_ORDER (0) // 0/1
#define ESP_PANEL_LCD_INEVRT_COLOR (0) // 0/1
/* LCD Transformation Flags */
#define ESP_PANEL_LCD_SWAP_XY (0) // 0/1
#define ESP_PANEL_LCD_MIRROR_X (0) // 0/1
#define ESP_PANEL_LCD_MIRROR_Y (0) // 0/1
/* LCD Other Settings */
/* IO num of RESET pin, set to -1 if not use */
#define ESP_PANEL_LCD_IO_RST (-1)
#define ESP_PANEL_LCD_RST_LEVEL (0) // 0: low level, 1: high level
#endif /* ESP_PANEL_USE_LCD */
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
//////////////////////////// Please update the following macros to configure the touch panel ///////////////////////////
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/* Set to 1 when using an touch panel */
#define ESP_PANEL_USE_TOUCH (1) // 0/1
#if ESP_PANEL_USE_TOUCH
/**
* Touch controller name. Choose one of the following:
* - CST816S
* - FT5x06
* - GT911, GT1151
* - TT21100
*/
#define ESP_PANEL_TOUCH_NAME GT911
/* Touch resolution in pixels */
#define ESP_PANEL_TOUCH_H_RES (ESP_PANEL_LCD_WIDTH) // Typically set to the same value as the width of LCD
#define ESP_PANEL_TOUCH_V_RES (ESP_PANEL_LCD_HEIGHT) // Typically set to the same value as the height of LCD
/* Touch Panel Bus Settings */
/**
* If set to 1, the bus will skip to initialize the corresponding host. Users need to initialize the host in advance.
* It is useful if other devices use the same host. Please ensure that the host is initialized only once.
*/
#define ESP_PANEL_TOUCH_BUS_SKIP_INIT_HOST (0) // 0/1
/**
* Touch panel bus type. Choose one of the following:
* - ESP_PANEL_BUS_TYPE_I2C
* - ESP_PANEL_BUS_TYPE_SPI (not ready)
*/
#define ESP_PANEL_TOUCH_BUS_TYPE (ESP_PANEL_BUS_TYPE_I2C)
/* Touch panel bus parameters */
#if ESP_PANEL_TOUCH_BUS_TYPE == ESP_PANEL_BUS_TYPE_I2C
#define ESP_PANEL_TOUCH_BUS_HOST_ID (0) // Typically set to 0
#define ESP_PANEL_TOUCH_I2C_ADDRESS (0) // Typically set to 0 to use default address
#if !ESP_PANEL_TOUCH_BUS_SKIP_INIT_HOST
#define ESP_PANEL_TOUCH_I2C_CLK_HZ (400 * 1000)
// Typically set to 400K
#define ESP_PANEL_TOUCH_I2C_SCL_PULLUP (1) // 0/1
#define ESP_PANEL_TOUCH_I2C_SDA_PULLUP (1) // 0/1
#define ESP_PANEL_TOUCH_I2C_IO_SCL (9)
#define ESP_PANEL_TOUCH_I2C_IO_SDA (8)
#endif
#else
#error "The function is not ready and will be implemented in the future."
#endif /* ESP_PANEL_TOUCH_BUS_TYPE */
/* Touch Transformation Flags */
#define ESP_PANEL_TOUCH_SWAP_XY (0) // 0/1
#define ESP_PANEL_TOUCH_MIRROR_X (0) // 0/1
#define ESP_PANEL_TOUCH_MIRROR_Y (0) // 0/1
/* Touch Other Settings */
/* IO num of RESET pin, set to -1 if not use */
#define ESP_PANEL_TOUCH_IO_RST (-1)
#define ESP_PANEL_TOUCH_RST_LEVEL (0) // 0: low level, 1: high level
/* IO num of INT pin, set to -1 if not use */
#define ESP_PANEL_TOUCH_IO_INT (-1)
#define ESP_PANEL_TOUCH_INT_LEVEL (0) // 0: low level, 1: high level
#endif /* ESP_PANEL_USE_TOUCH */
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
///////////////////////////// Please update the following macros to configure the backlight ////////////////////////////
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
#define ESP_PANEL_USE_BACKLIGHT (0) // 0/1
#if ESP_PANEL_USE_BACKLIGHT
/* IO num of backlight pin */
#define ESP_PANEL_BACKLIGHT_IO (45)
#define ESP_PANEL_BACKLIGHT_ON_LEVEL (1) // 0: low level, 1: high level
/* Set to 1 if you want to turn off the backlight after initializing the panel; otherwise, set it to turn on */
#define ESP_PANEL_BACKLIGHT_IDLE_OFF (0) // 0: on, 1: off
/* Set to 1 if use PWM for brightness control */
#define ESP_PANEL_LCD_BL_USE_PWM (1) // 0/1
#endif /* ESP_PANEL_USE_BACKLIGHT */
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
///////////////////////////// Please update the following macros to configure the IO expander //////////////////////////
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/* Set to 0 if not using IO Expander */
#define ESP_PANEL_USE_EXPANDER (0) // 0/1
#if ESP_PANEL_USE_EXPANDER
/**
* IO expander name. Choose one of the following:
* - HT8574
* - TCA95xx_8bit
* - TCA95xx_16bit
* - CH422G
*/
#define ESP_PANEL_EXPANDER_NAME CH422G
/* IO expander Settings */
/**
* If set to 1, the driver will skip to initialize the corresponding host. Users need to initialize the host in advance.
* It is useful if other devices use the same host. Please ensure that the host is initialized only once.
*/
#define ESP_PANEL_EXPANDER_SKIP_INIT_HOST (1) // 0/1
/* IO expander parameters */
#define ESP_PANEL_EXPANDER_I2C_ADDRESS (0x20)
#if !ESP_PANEL_EXPANDER_SKIP_INIT_HOST
#define ESP_PANEL_EXPANDER_HOST_ID (0) // Typically set to 0
#define ESP_PANEL_EXPANDER_I2C_CLK_HZ (400 * 1000)
// Typically set to 400K
#define ESP_PANEL_EXPANDER_I2C_SCL_PULLUP (1) // 0/1
#define ESP_PANEL_EXPANDER_I2C_SDA_PULLUP (1) // 0/1
#define ESP_PANEL_EXPANDER_I2C_IO_SCL (18)
#define ESP_PANEL_EXPANDER_I2C_IO_SDA (8)
#endif
#endif /* ESP_PANEL_USE_EXPANDER */
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
///////////////////////////// Please utilize the following macros to execute any additional code if required. //////////
////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
// #define ESP_PANEL_BEGIN_START_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_EXPANDER_START_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_EXPANDER_END_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_LCD_START_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_LCD_END_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_TOUCH_START_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_TOUCH_END_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_BACKLIGHT_START_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_BACKLIGHT_END_FUNCTION( panel )
// #define ESP_PANEL_BEGIN_END_FUNCTION( panel )
#endif /* ESP_PANEL_USE_CUSTOM_BOARD */
// *INDENT-OFF*
Version
v3.0.0
IDE Name
Arduino IDE
Operating System
Windows 10
Flash frequency
80MHz
PSRAM enabled
yes
Upload speed
921600
Description
I bought a Wareshare ESP32-S3-Touch-LCD-7 board from Aliexpress for some LVGL projects and I believe this board is using ESP32-S3-WROOM-1-N8R8. The LCD works fine out of the box. I can run LVGL widget demo on the LCD. Then I uploaded an "LVGL porting" code from the "ESP32 Display Panel" library and changed the demo to music player which works fine as well.
However, I unplugged the USB cord and plugged the board again. The program did not run properly. The LCD display showed nothing. Here is my board configuration:
Sometimes, the program can start normally without error messages. But 9 out of 10 times will fail. I used to use TFT_eSPI and it is the first I got involved in ESP32_Display_Panel. Any advice on how I can resolve the issues? Many Thanks!
Sketch
/**
* # LVGL Porting Example
*
* The example demonstrates how to port LVGL (v8.3.x). And for RGB LCD, it can enable the avoid tearing fucntion.
*
* ## How to Use
*
* To use this example, please firstly install the following dependent libraries:
*
* - lvgl (v8.3.x)
*
* Then follow the steps below to configure:
*
* 1. For **ESP32_Display_Panel**:
*
* - [Configure drivers](https://github.com/esp-arduino-libs/ESP32_Display_Panel#configuring-drivers) if needed.
* - If using a supported development board, follow the [steps](https://github.com/esp-arduino-libs/ESP32_Display_Panel#using-supported-development-boards) to configure it.
* - If using a custom board, follow the [steps](https://github.com/esp-arduino-libs/ESP32_Display_Panel#using-custom-development-boards) to configure it.
*
* 2. Follow the [steps](https://github.com/esp-arduino-libs/ESP32_Display_Panel#configuring-lvgl) to configure the **lvgl**.
* 3. Modify the macros in the [lvgl_port_v8.h](./lvgl_port_v8.h) file to configure the LVGL porting parameters.
* 4. Navigate to the `Tools` menu in the Arduino IDE to choose a ESP board and configure its parameters, please refter to [Configuring Supported Development Boards](https://github.com/esp-arduino-libs/ESP32_Display_Panel#configuring-supported-development-boards)
* 5. Verify and upload the example to your ESP board.
*
* ## Serial Output
*
*
* ...
* LVGL porting example start
* Initialize panel device
* Initialize LVGL
* Create UI
* LVGL porting example end
* IDLE loop
* IDLE loop
* ...
*
*
* ## Troubleshooting
*
* Please check the [FAQ](https://github.com/esp-arduino-libs/ESP32_Display_Panel#faq) first to see if the same question exists. If not, please create a [Github issue](https://github.com/esp-arduino-libs/ESP32_Display_Panel/issues). We will get back to you as soon as possible.
*
*/
#include <Arduino.h>
#include <ESP_Panel_Library.h>
#include <lvgl.h>
#include "lvgl_port_v8.h"
#include <demos/lv_demos.h>
/**
/* To use the built-in examples and demos of LVGL uncomment the includes below respectively.
* You also need to copy `lvgl/examples` to `lvgl/src/examples`. Similarly for the demos `lvgl/demos` to `lvgl/src/demos`.
*/
// #include <demos/lv_demos.h>
// #include <examples/lv_examples.h>
void setup()
{
String title = "LVGL porting example";
Serial.begin(115200);
Serial.println(title + " start");
Serial.println("Initialize panel device");
ESP_Panel *panel = new ESP_Panel();
panel->init();
#if LVGL_PORT_AVOID_TEAR
// When avoid tearing function is enabled, configure the RGB bus according to the LVGL configuration
ESP_PanelBus_RGB *rgb_bus = static_cast<ESP_PanelBus_RGB *>(panel->getLcd()->getBus());
rgb_bus->configRgbFrameBufferNumber(LVGL_PORT_DISP_BUFFER_NUM);
rgb_bus->configRgbBounceBufferSize(LVGL_PORT_RGB_BOUNCE_BUFFER_SIZE);
#endif
panel->begin();
Serial.println("Initialize LVGL");
lvgl_port_init(panel->getLcd(), panel->getTouch());
Serial.println("Create UI");
/* Lock the mutex due to the LVGL APIs are not thread-safe */
lvgl_port_lock(-1);
/* Create a simple label */
lv_obj_t *label = lv_label_create(lv_scr_act());
lv_label_set_text(label, title.c_str());
lv_obj_align(label, LV_ALIGN_CENTER, 0, 0);
/**
* Try an example. Don't forget to uncomment header.
* See all the examples online: https://docs.lvgl.io/master/examples.html
* source codes: https://github.com/lvgl/lvgl/tree/e7f88efa5853128bf871dde335c0ca8da9eb7731/examples
*/
// lv_example_btn_1();
/**
* Or try out a demo.
* Don't forget to uncomment header and enable the demos in `lv_conf.h`. E.g. `LV_USE_DEMOS_WIDGETS`
*/
// lv_demo_widgets();
lv_demo_benchmark();
// lv_demo_music();
// lv_demo_stress();
/* Release the mutex */
lvgl_port_unlock();
Serial.println(title + " end");
}
void loop()
{
Serial.println("IDLE loop");
delay(1000);
}Debug Message
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3818,len:0x508
load:0x403c9700,len:0x4
load:0x403c9704,len:0xad0
load:0x403cc700,len:0x29e4
entry 0x403c9880
LVGL porting example start
Initialize panel device
E (30) lcd_panel.io.i2c: panel_io_i2c_rx_buffer(135): i2c transaction failed
E (30) GT911: touch_gt911_read_cfg(362): GT911 read error!
E (31) GT911: esp_lcd_touch_new_i2c_gt911(128): GT911 init failed
E (37) GT911: Error (0xffffffff)! Touch controller GT911 initialization failed!
Initialize LVGL
Create UI
LVGL porting example end
IDLE loop
IDLE loop
Other Steps to Reproduce
No response
I have checked existing issues, online documentation and the Troubleshooting Guide
- I confirm I have checked existing issues, online documentation and Troubleshooting guide.
E (30) lcd_panel.io.i2c: panel_io_i2c_rx_buffer(135): i2c transaction failed
E (30) GT911: touch_gt911_read_cfg(362): GT911 read error!
E (31) GT911: esp_lcd_touch_new_i2c_gt911(128): GT911 init failed
E (37) GT911: Error (0xffffffff)! Touch controller GT911 initialization failed!
This is about the Touch Screen. It seems like the I2C pins are not being set correctly.
#define ESP_PANEL_USE_BACKLIGHT (0) // 0/1
Is it correct? The display may fail 9 of 10 times, after first boot, because there is no Back Light on in order to see the display....
@SuGlider, thanks for the quick response. I will check #define ESP_PANEL_USE_BACKLIGHT to see if that is the issue.
When I received the board, I used esptool to backup the factory firmware with the LVGL demo. With that "factory" firmware, I can upload the customized LVGL project via Arduino and the LCD display works flawlessly with customized LVGL content. Then if I unplug the USB and reconnect the board to either PC or external power source, the display shows nothing and those error messages pop up. I think I see some backlight from the display.
If I understand it correctly, the original firmware that came installed in the display works fine.
But when you upload the Arduino Sketch presented in this issue, it doesn't work, with a back display and error messages.
If this is correct, the problem is in the Arduino Sketch code.
No. If I restore the original firmware to the board and then upload my Arduino sketch, the display works fine. However, if I unplug the USB and reconnect it, the board stops working.
I understand this issue might seem unusual, and I apologize if it's difficult to explain.
There is a documentatio and instructions in https://www.waveshare.com/wiki/ESP32-S3-Touch-LCD-7
It says that Flash is QIO 120MHz to align with the PSRAM. Your setup says QIO 80MHz.
Check the Notes with the IDF configuration. Maybe Arduino can't be used as written there:
CONFIG_IDF_EXPERIMENTAL_FEATURES=y and CONFIG_SPIRAM_SPEED_120M=y [should align with PSRAM]
CONFIG_FREERTOS_HZ=1000
CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_240=y
CONFIG_ESPTOOLPY_FLASHMODE_QIO=y
CONFIG_ESPTOOLPY_FLASHFREQ_120M=y [should align with PSRAM]
CONFIG_SPIRAM_MODE_OCT=y
CONFIG_IDF_EXPERIMENTAL_FEATURES=y and CONFIG_SPIRAM_SPEED_120M=y [should align with PSRAM]
CONFIG_SPIRAM_FETCH_INSTRUCTIONS=y
CONFIG_SPIRAM_RODATA=y
CONFIG_ESP32S3_DATA_CACHE_LINE_64B=y
CONFIG_COMPILER_OPTIMIZATION_PERF=y
#The following LVGL configuration can improve the frame rate (LVGL v8.3):
#define LV_MEM_CUSTOM 1 or CONFIG_LV_MEM_CUSTOM=y
#define LV_MEMCPY_MEMSET_STD 1 or CONFIG_LV_MEMCPY_MEMSET_STD=y
#define LV_ATTRIBUTE_FAST_MEM IRAM_ATTR or CONFIG_LV_ATTRIBUTE_FAST_MEM=y
@zyan003 - I think that, in order to use Arduino, you will have to build using Arduino as IDF Component, instead of using the Arduino IDE with specific/fixed IDF setup.
Doubt the settings are the reason for the issue. This settings "just" enhances the display speed. Without the display will work too. There will be probably screen flicker appear.
Overall the recommended settings make no sense at all. QIO running @120 Mhz is not needed since the config
CONFIG_SPIRAM_FETCH_INSTRUCTIONS=y
CONFIG_SPIRAM_RODATA=y
will move flash content into the fast OPI PSRAM and the "slow" QIO Flash will not accessed anymore!
Edit: use the "speed" OPI settings in our Arduino fork and managed to avoid screen flicker with some Displays and Tasmota.
Now, with all parameters remain unchanged, if I hold the "RESET" button when powering up, then open serial monitor, then press "RESET" again, LCD starts showing content and the touch works fine as well. The program works now, but it is not yet a flawless solution.
The Device has an UART port too. Changing the setup to use this port will probably solve the strange behaviour.
What Arduino Core version is being used?
If you are using Arduino Core 3.0.x, please enable the Core Debug Level to Verbose and post here the serial monitor output.
You can also try building it with the Arduino Core 2.0.17, just in case.
I found out that the issue is caused by GT911 power up timing and delay. Now, after adding
ESP_IOExpander *expander = new ESP_IOExpander_CH422G((i2c_port_t)I2C_MASTER_NUM, ESP_IO_EXPANDER_I2C_CH422G_ADDRESS_000, I2C_MASTER_SCL_IO, I2C_MASTER_SDA_IO);
expander->init();
expander->begin();
expander->multiPinMode(TP_RST | LCD_BL | LCD_RST | SD_CS | USB_SEL, OUTPUT);
expander->multiDigitalWrite(TP_RST | LCD_BL | LCD_RST, HIGH);
delay(100);
expander->multiDigitalWrite(TP_RST | LCD_RST, LOW);
delay(100);
digitalWrite(GPIO_INPUT_IO_4, LOW);
delay(100);
expander->multiDigitalWrite(TP_RST | LCD_RST, HIGH);
delay(200);
in void main(), the display works flawlessly.