no WLAN-connection
atifan opened this issue · comments
I can compile, and upload to a WEMOS D1 Mini, but the WEMOS does not connect ty my WLAN. In credentials.h there is set the SSID1 and the Password.
Any ideas why it is not working?
// defines for the credentials
#define SSID1 "mySSID"
#define PW1 "mypasswd"
#define MQTT1 "192.168.178.111"
#define SSID2 "mySSID"
#define PW2 "mypasswd"
#define MQTT2 "192.168.178.111"
#define SSID3 "mySSID"
#define PW3 "mypasswd"
#define MQTT3 "192.168.178.111"
#define W_ENCRYPTION_KEY 0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, 0x88, 0x99, 0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff
#define W_SERIAL_NUMBER 0x12, 0x34, 0x056, 0x78
What does the Serial Console say ?
It will normally output some debug information on scanning and connecting to the wifi.
Hi it says
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
Soft WDT reset
stack>>>
ctx: cont
sp: 3ffffda0 end: 3fffffc0 offset: 01a0
3fffff40: 40208ef5 000000f5 3ffee82c 4020130c
3fffff50: 3fffdad0 000000f5 3ffee900 402013e9
3fffff60: 000000ff 00000000 00000036 402013b7
3fffff70: 3fffdad0 00000000 3ffee82c 40201471
3fffff80: 0001c200 00000000 3ffee82c 40201660
3fffff90: 3fffdad0 00000000 3ffee930 40201e58
3fffffa0: feefeffe feefeffe 3ffeea1c 402084f0
3fffffb0: feefeffe feefeffe 3ffe8528 401010b1
<<<stack<<<
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
load 0x4010f000, len 3584, room 16
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
Soft WDT reset
stack>>>
ctx: cont
sp: 3ffffda0 end: 3fffffc0 offset: 01a0
3fffff40: 40208ef5 000000f5 3ffee82c 4020130c
3fffff50: 3fffdad0 000000f5 3ffee900 402013e9
3fffff60: 000000ff 00000000 00000036 402013b7
3fffff70: 3fffdad0 00000000 3ffee82c 40201471
3fffff80: 0001c200 00000000 3ffee82c 40201660
3fffff90: 3fffdad0 00000000 3ffee930 40201e58
3fffffa0: feefeffe feefeffe 3ffeea1c 402084f0
3fffffb0: feefeffe feefeffe 3ffe8528 401010b1
<<<stack<<<
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
load 0x4010f000, len 3584, room 16
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
Soft WDT reset
stack>>>
ctx: cont
sp: 3ffffda0 end: 3fffffc0 offset: 01a0
3fffff40: 40208ef5 000000f5 3ffee82c 4020130c
3fffff50: 3fffdad0 000000f5 3ffee900 402013e9
3fffff60: 000000ff 00000000 00000036 402013b7
3fffff70: 3fffdad0 00000000 3ffee82c 40201471
3fffff80: 0001c200 00000000 3ffee82c 40201660
3fffff90: 3fffdad0 00000000 3ffee930 40201e58
3fffffa0: feefeffe feefeffe 3ffeea1c 402084f0
3fffffb0: feefeffe feefeffe 3ffe8528 401010b1
<<<stack<<<
--------------- CUT HERE FOR EXCEPTION DECODER ---------------
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
load 0x4010f000, len 3584, room 16
tail 0
chksum 0xb0
csum 0xb0
v2843a5ac
~ld
Hello, i fixed it.
Problem was that I did not connect the CC1101. It has to be connected to the ESP, that the ESP starts. When not connected, the ESP does not boot up.