T-Beam v1.2 GPS not working
Sailorspoon opened this issue · comments
SOC
ESP32
Lora IC
LILYGO LORA32 868/915MHz
Description
I am trying to figure out why the GPS module is not working.
I already tested the GPS reset and test firmware and the NMEA reset.
According to the data send to the serial monitor the GPS module can not be found.
Is this related to the AXP2101 chip of the 1.2 version or is this a hardware issue?
Here are the serial messages appearing when testing the different fixes:
GPS_reset.bin:
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1216
ho 0 tail 12 room 4
load:0x40078000,len:10944
load:0x40080400,len:6388
entry 0x400806b4
Connected to Serial
AXP192 Begin FAIL
All comms started
===== STATE 0
GPS_BasicNMEARead.bin
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1044
load:0x40078000,len:10124
load:0x40080400,len:5856
entry 0x400806a8
initBoard
AXP192 false
SparkFun Ublox Example
Sending: CLS:CFG ID:RATE Len: 0x0 Payload:
sendCommand: Waiting for ACK response
waitForACKResponse: TIMEOUT after 1100 msec.
Ublox GPS not detected at default I2C address. Please check wiring. Freezing
NMEA_Reset:
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13192
load:0x40080400,len:3028
entry 0x400805e4
initBoard
AXP2101 PMU init succeeded, using AXP2101 PMU
DC1 : + Voltage: 3300 mV
DC2 : - Voltage: 0500 mV
DC3 : - Voltage: 3300 mV
DC4 : - Voltage: 1840 mV
DC5 : - Voltage: 3300 mV
ALDO1: - Voltage: 3300 mV
ALDO2: + Voltage: 3300 mV
ALDO3: + Voltage: 3300 mV
ALDO4: - Voltage: 3300 mV
BLDO1: - Voltage: 3300 mV
BLDO2: - Voltage: 3300 mV
=========================================
PowerKeyPressOffTime:4 Second
Started OLED
recovery failed!
Hardware_test/t-beam-v1.x/Comprehensive/firmware_SX1276_868M.bin
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13192
load:0x40080400,len:3028
entry 0x400805e4
+-+-+-+-+-+-+ +-+-+-+-+-+ +-+-+ +-+-+-+-+
|L|i|l|y|G|o| |T|B|e|a|m| |S|3| |C|o|r|e|
+-+-+-+-+-+-+ +-+-+-+-+-+ +-+-+ +-+-+-+-+
-----------------------------------
Reset reason: In case of deep sleep, reset was not caused by exit from deep slee p
PSRAM is enable! PSRAM: 4.00MB
Falsh:4 MB
Falsh speed:40 M
Model:ESP32-D0WDQ6-V3
Chip Revision:3
Freq:240 MHZ
SDK Ver:v4.4.4
DATE:Jul 12 2023
TIME:16:44:34
EFUSE MAC: 08:B6:1F:A0:65:B4
-----------------------------------
32K XTAL OSC has not started upWarning: Failed to set rtc clk to 32.768Khz !!!
========================================
========================================
setupPower
AXP2101 PMU init succeeded, using AXP2101 PMU
=========================================
DC1 : + Voltage: 3300 mV
DC2 : - Voltage: 0500 mV
DC3 : - Voltage: 0500 mV
DC4 : - Voltage: 1800 mV
DC5 : - Voltage: 3300 mV
ALDO1: - Voltage: 1800 mV
ALDO2: + Voltage: 3300 mV
ALD O3: + Voltage: 3300 mV
ALDO4: - Voltage: 3300 mV
BLDO1: - Voltage: 1800 mV
BLDO2: - Voltage: 3300 mV
=========================================
PowerKeyPr essOffTime:4 Second
========================================
========================================
[ OLED ] Started OLED
Find display model SSD1306
========================================
========================================
setupRadio
Start Radio success!
========================================
setupGPS
Try to init L76K
Are you using the M10Q version? It seems that communication is indeed impossible. Contact the dealer for replacement.
If you are refering to the GPS module, I don't think it is the M10Q version.
It says ublox NEO-6M-0-001 on the module.
I will contact the dealer for replacement.
This issue is stale because it has been open for 30 days with no activity.
This issue was closed because it has been inactive for 14 days since being marked as stale.