Giters

MonkWho / pfatt

Enable true bridge mode for AT&T U-Verse and pfSense (this is a fork of an original repository https://github.com/aus/pfatt. Since it is not available anymore, I'll do my best to maintain a copy for people that still need a bypass)

Geek Repo:Geek Repo

Github PK Tool:Github PK Tool

ngeth0 interface unavailable on reboot after 21.02 upgrade

aholmes55 opened this issue · comments

commented

I recently upgraded from 2.4.5p1 to 21.02p1 on my Netgate SG-4860. The configuration is unable to find my netgraph bridge for the WAN connection and runs the interface assignment option where I can select ngeth0 for the WAN and everything works. I have to do this every reboot. Appreciate any help

`Initializing.................... done.
Starting device manager (devd)...done.
Loading configuration......done.
ngeth0: link state changed to UP
igb2: permanently promiscuous mode enabled
igb1: permanently promiscuous mode enabled
Updating configuration...done.
Warning: Configuration references interfaces that do not exist: ngeth0

Network interface mismatch -- Running interface assignment option.

Valid interfaces are:

igb0 00:08:a2:0f:df:db (down) Intel(R) PRO/1000 PCI-Express Network Driver
igb1 00:08:a2:0f:df:dc (down) Intel(R) PRO/1000 PCI-Express Network Driver
igb2 00:08:a2:0f:df:d7 (down) Intel(R) PRO/1000 PCI-Express Network Driver
igb3 00:08:a2:0f:df:d8 (down) Intel(R) PRO/1000 PCI-Express Network Driver
igb4 00:08:a2:0f:df:d9 (down) Intel(R) PRO/1000 PCI-Express Network Driver
igb5 00:08:a2:0f:df:da (down) Intel(R) PRO/1000 PCI-Express Network Driver
ngeth0 dc:7f:a4:XX:XX:XX (up)

Do VLANs need to be set up first?
If VLANs will not be used, or only for optional interfaces, it is typical to
say no here and use the webConfigurator to configure VLANs later, if required.

Should VLANs be set up now [y|n]? igb2: link state changed to UP
igb1: link state changed to UP
igb0: link state changed to UP

If the names of the interfaces are not known, auto-detection can
be used instead. To use auto-detection, please disconnect all
interfaces before pressing 'a' to begin the process.

Enter the WAN interface name or 'a' for auto-detection
(igb0 igb1 igb2 igb3 igb4 igb5 ngeth0 or a): ngeth0

Enter the LAN interface name or 'a' for auto-detection
NOTE: this enables full Firewalling/NAT mode.
(igb0 igb1 igb2 igb3 igb4 igb5 a or nothing if finished): igb0

Optional interface 1 description found: OPT1
Enter the Optional 1 interface name or 'a' for auto-detection
(igb1 igb2 igb3 igb4 igb5 a or nothing if finished): igb2

Optional interface 2 description found: OPT2
Enter the Optional 2 interface name or 'a' for auto-detection
(igb1 igb3 igb4 igb5 a or nothing if finished): igb3

Optional interface 3 description found: OPT3
Enter the Optional 3 interface name or 'a' for auto-detection
(igb1 igb4 igb5 a or nothing if finished): igb4

Optional interface 4 description found: OPT4
Enter the Optional 4 interface name or 'a' for auto-detection
(igb1 igb5 a or nothing if finished): igb5

Enter the Optional 5 interface name or 'a' for auto-detection
(igb1 a or nothing if finished):

The interfaces will be assigned as follows:

WAN -> ngeth0
LAN -> igb0
OPT1 -> igb2
OPT2 -> igb3
OPT3 -> igb4
OPT4 -> igb5

Do you want to proceed [y|n]? y

Writing configuration.....................................................................................................done.
One moment while the settings are reloading... done!
..Configuring looplo0: link state changed to UP
back interface...done.
Creating wireless clone interfaces...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring IPsec VTI interfaces...done.
Configuring WAN interface...done.
Configuring LAN interface...igb0: link state changed to DOWN
done.
bridge0: Ethernet address: 58:9c:fc:XX:XX:XX
igb0: promiscuous mode enabled
bridge0: link state changed to UP
Checking config backups consistency...done.
Setting up extended sysctls...done.
coretemp0: on cpu0
Setting timezone...done.
2021-03-06T06:53:59.807445-06:00 router.XXXXXX.XXX php-fpm 351 - - /rc.newwanip: rc.newwanip: Info: starting on ngeth0.

2021-03-06T06:53:59.808827-06:00 router.XXXXXX.XXX php-fpm 351 - - /rc.newwanip: rc.newwanip: on (IP address: 69.XXX.XXX.XXX) (interface: WAN[wan]) (real interface: ngeth0).
`

commented

I solved this by adding netgh to the ignored interfaces in /etc/inc/util.inc at Line number 2385.
Add ^ngeth| to the list of interfaces.

https://github.com/pfsense/pfsense/blob/RELENG_2_5_0/src/etc/inc/util.inc#L2385